新增兼容两种墙壁开关

component/xc6xx_drivers/Drivers/CMSIS/Device/xc6xxx.h

@@ -247,8 +247,8 @@ do { \
         (__HANDLE__)->Lock = HAL_UNLOCKED;                                     \
     } while (0U)
 
-#if ((__ARMCC_VERSION % 1000) != 750)
-    #error "Compiler build number mismatch. Required: build 750."
+#if ((__ARMCC_VERSION % 1000) != 960)
+    #error "Compiler build number mismatch. Required: build 960."
 #endif
 
 /* Macro to get variable aligned on 4-bytes, for __ICCARM__ the directive

project/example/ble/ble_peripheral/app/src/rf433.c

@@ -42,7 +42,7 @@ uint8_t adress_ch2_index = 0;   // 通道2地址索引（0-4）
 uint8_t match_ch = 0;    // 匹配到的通道（1=GPIO5，2=GPIO2）
 
  
-#define MATCH_CH1 0          // HPW421 不使用通道1
+#define MATCH_CH1		(1 << 0)        //GPIO5
 #define MATCH_CH2 	(1 << 1)  // 通道2匹配标记
 
 
@@ -92,8 +92,6 @@ void chx_gpio_init(void)
 		GPIO_InitCfg.FunSel = GPIO_Dx;        // 选择GPIO功能（非特殊功能）
 		GPIO_InitCfg.Pull   = GPIO_NOPULL;    //下拉电阻使能
 		
-		GPIO_InitCfg.Dir = GPIO_DIR_OUTPUT;    // 输出方向
-		GPIO_InitCfg.Int = NOT_INT;           // 不使能中断
 		GPIO_InitCfg.Dir = GPIO_DIR_OUTPUT;    // 输出方向
 		GPIO_InitCfg.Int = NOT_INT;           // 不使能中断
 		GPIO_InitCfg.Pin = RELAY_CH2_PIN;         // 设置通道2引脚
@@ -143,17 +141,10 @@ void app_key_callback_handler(uint16_t key_value)		//按键回调函数
 		case	MODE_DOUBLE_CLICK:		//双击
 		
 				 key_state=KEY_SHORT;
-					 power=3;
+					 power=4;
 				 led_state=2;			
 			break;
 			
-		case 	MODE_QUAD_CLICK:			//四击			
-				 key_state=KEY_SHORT;
-				 power=3;
-				 led_state=2;			
-			break;
-
-		
 		default:  
             break;
 	}
@@ -167,17 +158,11 @@ void ble_mode_scan(void)
 	 {
 					 switch(receive_mode)
 			 {
-				 case 1:
-						receive_mode=0;
-						 key_state=KEY_SHORT;
-						 power=3;
-						 led_state=2;			
-						break;
 				 
 				 case 2:
 					 receive_mode=0;
 					  key_state=KEY_SHORT;
-						power=3;
+						power=4;
 						led_state=2;			
 					 break;
 				 
@@ -202,7 +187,7 @@ void _433_fun(void)
 	switch(res_data)
 	{
 		case 0x03:						//如果是3键遥控或者是正方形白色遥控
-			 if(match_ch & MATCH_CH2){
+			 if(match_ch & MATCH_CH1){
             xc_gpio_toggle_pin(RELAY_CH2_PIN);	
             flash_ch2_state=xc_gpio_read_pin(RELAY_CH2_PIN);
             ble_state_mark_dirty(BLE_STATE_DIRTY_OUTPUT | BLE_STATE_DIRTY_RF433);
@@ -212,7 +197,7 @@ void _433_fun(void)
 				
 				
 		case 0x04:						//如果是黑色长方形遥控或者椭圆遥控关闭按键
-					if(match_ch & MATCH_CH2)
+					if(match_ch & MATCH_CH1)
 					{
 						xc_gpio_write_pin(RELAY_CH2_PIN,GPIO_PIN_RESET);
 						flash_ch2_state=xc_gpio_read_pin(RELAY_CH2_PIN);
@@ -221,7 +206,7 @@ void _433_fun(void)
 					break;
 					
 		case 0x02:						//如果是黑色长方形遥控或者椭圆遥控打开按键
-					if(match_ch & MATCH_CH2)
+					if(match_ch & MATCH_CH1)
 					{
 						xc_gpio_write_pin(RELAY_CH2_PIN,GPIO_PIN_SET);
 						flash_ch2_state=xc_gpio_read_pin(RELAY_CH2_PIN);
@@ -249,14 +234,14 @@ void scan_433(void)
 					long_timer--;
 				}
 	
-					if(rf433_sw_flag==1)
+//					if(rf433_sw_flag==1)
+//					{
+//						rf433_sw_flag=0;
+//					}
+					if(rf433_sw_flag==2)
 					{
 						rf433_sw_flag=0;
-					}
-					else if(rf433_sw_flag==2)
-					{
-						rf433_sw_flag=0;
-						power=3;
+						power=4;
 						key_state=KEY_SHORT;
 						led_state=2;
 					}
@@ -269,45 +254,45 @@ void scan_433(void)
 					
 					}
 					
-					if(power==3 && rf433_decoder_flag==true && key_state==KEY_SHORT )		//双击对码GPIO2
-				 {
+//					if(power==3 && rf433_decoder_flag==true && key_state==KEY_SHORT )		//双击对码GPIO2
+//				 {
+//					 
+//					
+//						key_state=0;
+//					  power=2;
+//					  led_state=0;
+//					 
+//					 
+//					 
+//					  if(adress_ch2_index>4)
+//					 {
+//						adress_ch2_index=0;
+//					 }
+//					 
+//					  adress_ture_flag=0;			
+//					  
+//					 for(i=0;i<5;i++)
+//					 {
+//							if(adress_H_ch2[i]==adress_H && adress_L_ch2[i]==adress_L)
+//							{
+//								adress_ture_flag=1;
+//								
+//								break;
+//							}
+//					 }
+//						if(adress_ture_flag==0)
+//						{
+//							 
+//							adress_H_ch2[adress_ch2_index] = adress_H;
+//							adress_L_ch2[adress_ch2_index] = adress_L;
+//							adress_ch2_index++; // 索引自增																					
+//						}
+//		
+//						
+//				 }
 				 
 				 
-						key_state=0;
-					  power=2;
-					  led_state=0;
-					 
-					 
-					 
-					  if(adress_ch2_index>4)
-					 {
-						adress_ch2_index=0;
-					 }
-					 
-					  adress_ture_flag=0;			
-					  
-					 for(i=0;i<5;i++)
-					 {
-							if(adress_H_ch2[i]==adress_H && adress_L_ch2[i]==adress_L)
-							{
-								adress_ture_flag=1;
-								
-								break;
-							}
-					 }
-						if(adress_ture_flag==0)
-						{
-							 
-							adress_H_ch2[adress_ch2_index] = adress_H;
-							adress_L_ch2[adress_ch2_index] = adress_L;
-							adress_ch2_index++; // 索引自增																					
-						}
-		
-						
-				 }
-				 
-				 
-				 else if(power==4 && rf433_decoder_flag==true && key_state==KEY_SHORT )		//四击对码GPIO5
+				 if(power==4 && rf433_decoder_flag==true && key_state==KEY_SHORT )		//四击对码GPIO5
 				 {
 					 
 					 
@@ -366,14 +351,14 @@ void scan_433(void)
 								}
 						}
 										
-						 for(i=0; i<5; i++)
-						{
-								if(adress_H_ch2[i]==adress_H && adress_L_ch2[i]==adress_L)
-								{
-										match_ch|= MATCH_CH2;       // 标记匹配到通道2						
-										break;
-								}
-						}
+//						 for(i=0; i<5; i++)
+//						{
+//								if(adress_H_ch2[i]==adress_H && adress_L_ch2[i]==adress_L)
+//								{
+//										match_ch|= MATCH_CH2;       // 标记匹配到通道2						
+//										break;
+//								}
+//						}
 						
 					
 						if(match_ch != 0)

project/example/ble/ble_peripheral/app/src/rf433_decoder.c

@@ -3,13 +3,13 @@
 
 #define RF433_FIFO_SIZE              256u
 
-#define RF433_GLITCH_DYNAMIC_MIN     2u
-#define RF433_GLITCH_DYNAMIC_MAX     4u
+#define RF433_GLITCH_DYNAMIC_MIN     1u		//2
+#define RF433_GLITCH_DYNAMIC_MAX     1u		//4
 
 #define RF433_SYNC_LOW_MIN           35u		//45改35
 #define RF433_SYNC_LOW_MAX           200u		//180改200
-#define RF433_SYNC_HIGH_MIN          1u			
-#define RF433_SYNC_HIGH_MAX          15u		//12改15
+#define RF433_SYNC_HIGH_MIN          2u			
+#define RF433_SYNC_HIGH_MAX          30u		//12改15
 
 #define RF433_BIT_LEN                24u
 #define RF433_REPEAT_CONFIRM         1u		//2改1
@@ -19,9 +19,9 @@
 #define RF433_BIT_TOTAL_MIN          3u		//4改3
 #define RF433_BIT_TOTAL_MAX          40u	//35改40
 
-#define RF433_PROCESS_MAX_ONCE       32u
+#define RF433_PROCESS_MAX_ONCE       64u
 
-#define RF433_FRAME_SCORE_MIN        50u		//70改50
+#define RF433_FRAME_SCORE_MIN        40u		//70改50
 #define RF433_BIT_SCORE_GOOD         4u
 #define RF433_BIT_SCORE_NORMAL       3u
 #define RF433_BIT_SCORE_POOR         1u
@@ -91,7 +91,7 @@ typedef struct
     Rf433DecoderFrame_t frame;
     bool frame_ready;
 	
-		uint16_t anti_repeat_tick; // 新增：连发屏蔽倒计时
+		
 } Rf433Decode_t;
 
 typedef struct
@@ -208,7 +208,7 @@ void rf433_decoder_init(void)
     s_dec.frame_ready = false;
     s_dec.ppl_locked = 0;
     s_dec.window_mode = RF433_WINDOW_NORMAL;
-		s_dec.anti_repeat_tick=0;					//新增
+		
 
     rf433_decode_reset();
     rf433_repair_reset();
@@ -284,7 +284,7 @@ static bool rf433_is_sync(uint16_t high, uint16_t low)
         return false;
     }
 
-    if (low < (uint16_t)(high * 10u))		//12
+    if (low < (uint16_t)(high * 12u))		//12
     {
         return false;
     }
@@ -500,8 +500,7 @@ static void rf433_output_code(uint32_t code)
         s_dec.last_code = code;
         s_dec.same_cnt = 1;
 			
-//			// 换码直接清空屏蔽计时，不同按键不拦截
-//        s_dec.anti_repeat_tick = 0;
+
     }
 
     RF433_DETAIL_LOG("[RF433 REPEAT] code=0x%06X same=%d/%d\r\n",
@@ -519,8 +518,7 @@ static void rf433_output_code(uint32_t code)
         s_dec.frame.score = s_dec.frame_score;
         s_dec.frame_ready = true;
 			
-//			// 输出后刷新连发屏蔽倒计时，一段时间内不再输出同码
-//        s_dec.anti_repeat_tick = RF433_ANTI_REPEAT_TICK;
+
 			
         s_dec.same_cnt = 0;
 
@@ -761,11 +759,7 @@ void rf433_decoder_process(void)
     Rf433Pulse_t pulse;
     uint8_t cnt = 0;
 	
-//	 // 新增：防重复倒计时全局递减
-//    if(s_dec.anti_repeat_tick > 0)
-//    {
-//        s_dec.anti_repeat_tick--;
-//    }
+
 	
 
     while ((cnt < RF433_PROCESS_MAX_ONCE) && rf433_fifo_pop(&pulse))

project/example/ble/ble_peripheral/app/src/switch_s.c

@@ -1,127 +1,260 @@
 #include "switch_s.h"
 #include "xc_drv_gpio.h"
 #include "rf433.h"
-// ==================== GPIO1 检测 ====================
-uint8_t trig1_cnt = 0;             // 连续触发次数
-uint16_t trig1_timeout = 0;        // 300ms 倒计时
-uint8_t trig1_wait = 0;            // 0=空闲 1=连续出触发
 
-// ==================== GPIO19 检测 ====================
-uint8_t trig2_cnt = 0;						 // 连续触发次数
-uint16_t trig2_timeout = 0;				 // 300ms 倒计时
-uint8_t trig2_wait = 0;						 // 0=空闲 1=连续出触发 
+/*
+ * ============================================================
+ * GPIO1 / S1 检测变量
+ * ============================================================
+ */
+uint8_t trig1_cnt = 0;
+uint16_t trig1_timeout = 0;
+uint8_t trig1_wait = 0;
 
-uint8_t rf433_sw_flag=0;			//进入对码标志
+/*
+ * ============================================================
+ * RF433 对码标志
+ * ============================================================
+ *
+ * 0：无对码
+ * 2：GPIO1 快速按 5 次及以上进入对码
+ */
+uint8_t rf433_sw_flag = 0;
 
+/*
+ * ============================================================
+ * 防抖状态机变量
+ * ============================================================
+ */
 static volatile debounce_state_t s1_state = DB_IDLE;
-static volatile debounce_state_t s2_state = DB_IDLE;
 static volatile uint16_t s1_debounce_cnt = 0;
-static volatile uint16_t s2_debounce_cnt = 0;
+
+/*
+ * ============================================================
+ * 按下持续时间计数
+ * ============================================================
+ */
+static volatile uint16_t s1_press_cnt = 0;
+
+/*
+ * ============================================================
+ * 长按普通开关已处理标志
+ * ============================================================
+ */
+static volatile uint8_t s1_long_press_done = 0;
+
+/*
+ * ============================================================
+ * 回弹点击标志
+ * ============================================================
+ */
+static volatile uint8_t s1_return_click_flag = 0;
+
+/*
+ * ============================================================
+ * 5次对码失效标志
+ * ============================================================
+ *
+ * 作用：
+ * 快速拨动达到 5 次后，如果最后一次停留在打开状态超过 200ms，
+ * 则本次 5 次对码序列失效。
+ *
+ * 这样可以避免：
+ * 快速拨动 5 次后停留在打开一段时间，再关闭，仍然进入对码。
+ */
+static volatile uint8_t s1_pair_invalid_flag = 0;
+
+/*
+ * ============================================================
+ * 防抖时间
+ * ============================================================
+ * trigger_check_process() 如果 10ms 调用一次：
+ * DEBOUNCE_MS = 2 表示 20ms 防抖
+ */
+#define DEBOUNCE_MS    2
+
+/*
+ * ============================================================
+ * 释放标志
+ * ============================================================
+ */
+uint8_t switch1_RELEASE_flag = 0;
+
+/*
+ * ============================================================
+ * 普通不回弹开关第一次按下标志
+ * ============================================================
+ */
+uint8_t s1_first_press_flag = 0;
+
+/*
+ * ============================================================
+ * 上电时开关状态
+ * ============================================================
+ */
+uint8_t S1_first_on_state = 0;
 
 
-
-#define DEBOUNCE_MS    2  		//消抖时间40ms
-
-//uint16_t switch1_debounce = 0;		
-//uint16_t switch2_debounce = 0;
-
-uint8_t switch1_RELEASE_flag=0;
-uint8_t switch2_RELEASE_flag=0;
-
-uint8_t s1_first_press_flag = 0; 	//S2首次按下标志
-uint8_t s2_first_press_flag = 0; 	//S2首次按下标志
-
-uint8_t S1_first_on_state=0;		//上电时开关的状态
-uint8_t S2_first_on_state=0;		//上电时开关的状态
-
-
-void switch_init(void)
+/*
+ * ============================================================
+ * S1 状态清理函数
+ * ============================================================
+ */
+static void switch_s1_clear_action_state(void)
 {
+    trig1_cnt = 0;
+    trig1_timeout = 0;
+    trig1_wait = 0;
 
-		GPIO_InitCfg_t GPIO_InitCfg = { 0 };  // 清零初始化配置结构体
-		GPIO_InitCfg.Mux    = GPIO_Mux0;      // 选择功能复用器0
-		GPIO_InitCfg.FunSel = GPIO_Dx;        // 选择GPIO功能（非特殊功能）
-		GPIO_InitCfg.Pull   = GPIO_PULLUP;    //上拉电阻使能
+    switch1_RELEASE_flag = 0;
+    s1_first_press_flag = 0;
 
+    s1_return_click_flag = 0;
+    s1_long_press_done = 0;
+    s1_press_cnt = 0;
 
-		GPIO_InitCfg.Dir = GPIO_DIR_INPUT;    // 输出方向
-		GPIO_InitCfg.Int = FAIL_EDGE_INT;     //使能中断
-		GPIO_InitCfg.Pin = SWITCH_S1_PIN;     // 设置S1引脚
-		xc_gpio_init(&GPIO_InitCfg);          // 初始化GPIO
-		
-		GPIO_InitCfg.Dir = GPIO_DIR_INPUT;    // 输出方向
-		GPIO_InitCfg.Int = FAIL_EDGE_INT;     //使能中断
-		GPIO_InitCfg.Pin = SWITCH_S2_PIN;     // 设置S2引脚
-		xc_gpio_init(&GPIO_InitCfg);          // 初始化GPIO
-		
-		xc_gpio_it_config(GPIO_1,FAIL_EDGE_INT);
-		xc_gpio_it_config(GPIO_19,FAIL_EDGE_INT);
-		NVIC_EnableIRQ(GPIO_IRQn);
-		
-		
-		//判断首次上电开关状态
-			if(xc_gpio_read_pin(SWITCH_S1_PIN)==0)
-			{
-				S1_first_on_state=1;
-			}
-			else
-			{
-				S1_first_on_state=0;
-			}
-			
-			if(xc_gpio_read_pin(SWITCH_S2_PIN)==0)
-			{
-				S2_first_on_state=1;
-			}
-			else
-			{
-				S2_first_on_state=0;
-			}
-		
+    /*
+     * 新增：
+     * 清理 5 次对码失效标志。
+     */
+    s1_pair_invalid_flag = 0;
 }
 
 
+/*
+ * ============================================================
+ * S1 输出控制：GPIO5
+ * ============================================================
+ */
+static void switch_s1_output_on(void)
+{
+    xc_gpio_write_pin(GPIO_5, GPIO_PIN_SET);
+    flash_ch1_state = xc_gpio_read_pin(GPIO_5);
+    flash_run();
+}
+
+static void switch_s1_output_off(void)
+{
+    xc_gpio_write_pin(GPIO_5, GPIO_PIN_RESET);
+    flash_ch1_state = xc_gpio_read_pin(GPIO_5);
+    flash_run();
+}
+
+static void switch_s1_output_toggle(void)
+{
+    if(xc_gpio_read_pin(GPIO_5))
+    {
+        xc_gpio_write_pin(GPIO_5, GPIO_PIN_RESET);
+    }
+    else
+    {
+        xc_gpio_write_pin(GPIO_5, GPIO_PIN_SET);
+    }
+
+    flash_ch1_state = xc_gpio_read_pin(GPIO_5);
+    flash_run();
+}
+
+
+/*
+ * ============================================================
+ * 开关 GPIO 初始化
+ * ============================================================
+ */
+void switch_init(void)
+{
+    GPIO_InitCfg_t GPIO_InitCfg = { 0 };
+
+    GPIO_InitCfg.Mux    = GPIO_Mux0;
+    GPIO_InitCfg.FunSel = GPIO_Dx;
+    GPIO_InitCfg.Pull   = GPIO_PULLUP;
+
+    /*
+     * GPIO1 输入初始化
+     */
+    GPIO_InitCfg.Dir = GPIO_DIR_INPUT;
+    GPIO_InitCfg.Int = FAIL_EDGE_INT;
+    GPIO_InitCfg.Pin = SWITCH_S1_PIN;
+    xc_gpio_init(&GPIO_InitCfg);
+
+    /*
+     * GPIO1 下降沿中断
+     */
+    xc_gpio_it_config(GPIO_1, FAIL_EDGE_INT);
+    NVIC_EnableIRQ(GPIO_IRQn);
+
+    /*
+     * 上电时检测 GPIO1 初始状态
+     */
+    if(xc_gpio_read_pin(SWITCH_S1_PIN) == 0)
+    {
+        S1_first_on_state = 1;
+    }
+    else
+    {
+        S1_first_on_state = 0;
+    }
+}
+
+
+/*
+ * ============================================================
+ * 开关检测主处理函数
+ * ============================================================
+ *
+ * 需要周期调用。
+ * 当前按 SWITCH_SCAN_PERIOD_MS = 10ms 计算。
+ */
 void trigger_check_process(void)
 {
-	if(S1_first_on_state==1)
+    /*
+     * ========================================================
+     * 上电时 GPIO1 已经按下
+     * ========================================================
+     */
+    if(S1_first_on_state == 1)
     {
-		S1_first_on_state=0;
-		
-		s1_state=DB_PRESS_DEBOUNCE;
-	}
-	if(S2_first_on_state==1)
-	{
-		S2_first_on_state=0;
-	
-		s2_state=DB_PRESS_DEBOUNCE;
+        S1_first_on_state = 0;
+        s1_state = DB_PRESS_DEBOUNCE;
+        s1_debounce_cnt = DEBOUNCE_MS;
     }
 
-//	if(S1_first_on_state==1)
-//	{
-//		S1_first_on_state=0;
-//		s1_first_press_flag=1;
-//		s1_state=DB_PRESSED;
-//	}
-//	if(S2_first_on_state==1)
-//	{
-//		S2_first_on_state=0;
-//		s2_first_press_flag=1;
-//		s2_state=DB_PRESSED;
-//	}
-	
+    /*
+     * ========================================================
+     * S1 状态机
+     * ========================================================
+     */
     switch(s1_state)
     {
-		 case DB_IDLE:		//空闲状态
+        case DB_IDLE:
+            /*
+             * 空闲状态低电平补检，防止漏中断。
+             */
+            if(xc_gpio_read_pin(SWITCH_S1_PIN) == 0)
+            {
+                s1_state = DB_PRESS_DEBOUNCE;
+                s1_debounce_cnt = DEBOUNCE_MS;
+            }
             break;
 
-		 case DB_PRESS_DEBOUNCE:		//按下防抖
-			 if(s1_debounce_cnt>0) s1_debounce_cnt--;
-				if(s1_debounce_cnt==0)
+        case DB_PRESS_DEBOUNCE:
+            if(s1_debounce_cnt > 0)
             {
-					//防抖时间到，采样当前电平是否是低电平
-					if(xc_gpio_read_pin(SWITCH_S1_PIN)==0)
+                s1_debounce_cnt--;
+            }
+
+            if(s1_debounce_cnt == 0)
             {
-									s1_state = DB_PRESSED; 	//进入按下状态，不响应中断
+                if(xc_gpio_read_pin(SWITCH_S1_PIN) == 0)
+                {
+                    s1_state = DB_PRESSED;
+
+                    s1_press_cnt = 0;
+                    s1_long_press_done = 0;
+
+                    /*
+                     * 连续触发计数
+                     */
                     if(trig1_wait == 0)
                     {
                         trig1_cnt = 1;
@@ -130,300 +263,325 @@ void trigger_check_process(void)
                     }
                     else
                     {
-										if(trig1_timeout>0)
+                        if(trig1_timeout > 0)
                         {
                             trig1_cnt++;
                         }
+                        else
+                        {
+                            /*
+                             * 如果等待标志还在，但超时已经为 0，
+                             * 说明旧状态异常，重新作为第一次点击。
+                             */
+                            trig1_cnt = 1;
+                        }
 
                         trig1_timeout = TRIGGER_TIMEOUT_MS;
-//									
                     }
                 }
                 else
                 {
-									// 杂波导致误触，回到空闲
                     s1_state = DB_IDLE;
                 }
             }
             break;
 
+        case DB_PRESSED:
+            /*
+             * 按下超过 200ms：
+             * 认为是普通不回弹墙壁开关，打开 GPIO5。
+             */
+            if(s1_long_press_done == 0)
+            {
+                if(s1_press_cnt < RETURN_SWITCH_CNT)
+                {
+                    s1_press_cnt++;
+                }
 
-				 case DB_PRESSED:					//确认按下
+                if(s1_press_cnt >= RETURN_SWITCH_CNT)
+                {
+                    s1_long_press_done = 1;
 
+                    /*
+                     * 普通不回弹开关只处理第一次有效按下。
+                     *
+                     * 注意：
+                     * 这里仍然要求 trig1_cnt == 1，
+                     * 避免快速多次点击被误判成长按开关打开。
+                     */
+                    if(trig1_cnt == 1 && trig1_wait == 1)
+                    {
+                        trig1_cnt = 0;
+                        trig1_timeout = 0;
+                        trig1_wait = 0;
 
+                        s1_return_click_flag = 0;
+                        switch1_RELEASE_flag = 0;
 
-            // 等待引脚回高电平
+                        s1_first_press_flag = 1;
+
+                        switch_s1_output_on();
+                    }
+                    else if(trig1_cnt >= TRIGGER_CONTINUE_CNT)
+                    {
+                        /*
+                         * ====================================================
+                         * 关键新增修复
+                         * ====================================================
+                         *
+                         * 如果已经快速拨动到了 5 次或以上，
+                         * 但是最后一次保持在打开状态超过 200ms，
+                         * 那么这一次对码序列作废。
+                         *
+                         * 后面即使再关闭，也不能进入对码。
+                         */
+                        s1_pair_invalid_flag = 1;
+
+                        /*
+                         * 防止旧的回弹点击标志残留。
+                         */
+                        s1_return_click_flag = 0;
+                        switch1_RELEASE_flag = 0;
+                    }
+                }
+            }
+
+            /*
+             * 检测释放
+             */
             if(xc_gpio_read_pin(SWITCH_S1_PIN) == 1)
             {
                 s1_state = DB_RELEASE_DEBOUNCE;
-                s1_debounce_cnt = DEBOUNCE_MS; // 释放30ms防抖
+                s1_debounce_cnt = DEBOUNCE_MS;
             }
             break;
 
-        case DB_RELEASE_DEBOUNCE:			//释放防抖
-            if(s1_debounce_cnt > 0) s1_debounce_cnt--;
+        case DB_RELEASE_DEBOUNCE:
+            if(s1_debounce_cnt > 0)
+            {
+                s1_debounce_cnt--;
+            }
+
             if(s1_debounce_cnt == 0)
             {
-                if(xc_gpio_read_pin(SWITCH_S1_PIN) == 1) // 确认释放
+                if(xc_gpio_read_pin(SWITCH_S1_PIN) == 1)
                 {
-                    s1_state = DB_IDLE; // 回到空闲
+                    s1_state = DB_IDLE;
+
+                    /*
+                     * ====================================================
+                     * 关键新增修复
+                     * ====================================================
+                     *
+                     * 如果前面已经判定：
+                     * 快速拨动 5 次后，最后一次停留打开超过 200ms，
+                     * 那么这次释放只是无效释放。
+                     *
+                     * 直接清理状态，不再进入后面的 5 次对码处理。
+                     */
+                    if(s1_pair_invalid_flag == 1)
+                    {
+                        switch_s1_clear_action_state();
+                    }
+                    else
+                    {
+                        /*
+                         * 释放后重新给连击窗口计时。
+                         */
                         trig1_timeout = TRIGGER_TIMEOUT_MS;
+                        switch1_RELEASE_flag = 1;
 
-										switch1_RELEASE_flag=1;
-									if(s1_first_press_flag==1)
+                        if(s1_long_press_done == 0)
                         {
-										s1_first_press_flag=2;	
-										
-									}
-										
+                            /*
+                             * 200ms 内释放：
+                             * 回弹点击。
+                             */
+                            s1_return_click_flag = 1;
                         }
                         else
                         {
-                    // 再等20ms
-                    s1_debounce_cnt = DEBOUNCE_MS; // 30ms
+                            /*
+                             * 普通不回弹开关释放。
+                             */
+                            if(s1_first_press_flag == 1)
+                            {
+                                s1_first_press_flag = 2;
                             }
                         }
-            break;
-	 }
-	
-
-	 
-	
-   switch(s2_state)
-	 {
-		 case DB_IDLE:		//空闲状态
-			 break;
-		 
-		 case DB_PRESS_DEBOUNCE:		//按下防抖
-			 if(s2_debounce_cnt>0) s2_debounce_cnt--;
-				if(s2_debounce_cnt==0)
-				{
-					//防抖时间到，采样当前电平是否是低电平
-					if(xc_gpio_read_pin(SWITCH_S2_PIN)==0)
-					{
-									s2_state = DB_PRESSED; 	//进入按下状态，不响应中断
-									if(trig2_wait == 0)
-									{
-											 trig2_cnt = 1;
-											 trig2_timeout = TRIGGER_TIMEOUT_MS;
-											 trig2_wait = 1;
-									}
-									else
-									{
-										if(trig2_timeout>0)
-										{
-												trig2_cnt++;	
-										}
-												
-										trig2_timeout = TRIGGER_TIMEOUT_MS; 																				
                     }
                 }
                 else
                 {
-									// 杂波导致误触，回到空闲
-									s2_state = DB_IDLE;
+                    s1_debounce_cnt = DEBOUNCE_MS;
                 }
             }
             break;
 
-				
-				 case DB_PRESSED:					//确认按下
-            // 等待引脚回高电平
-            if(xc_gpio_read_pin(SWITCH_S2_PIN) == 1)
-            {
-                s2_state = DB_RELEASE_DEBOUNCE;
-                s2_debounce_cnt = DEBOUNCE_MS; // 释放30ms防抖
-            }
-            break;
-
-        case DB_RELEASE_DEBOUNCE:			//释放防抖
-            if(s2_debounce_cnt > 0) s2_debounce_cnt--;
-            if(s2_debounce_cnt == 0)
-            {
-                if(xc_gpio_read_pin(SWITCH_S2_PIN) == 1) // 确认释放
-                {
-                    s2_state = DB_IDLE; // 回到空闲
-									 trig2_timeout = TRIGGER_TIMEOUT_MS;
-										switch2_RELEASE_flag=1;
-									if(s2_first_press_flag==1)
-									{
-										s2_first_press_flag=2;	
-										
-									}
-									
-									
-                }
-                else
-                {
-                    // 再等20ms
-                    s2_debounce_cnt = DEBOUNCE_MS; // 30ms
-                }
-            }
+        default:
+            s1_state = DB_IDLE;
             break;
     }
 
 
-	
-	  // S1 超时处理
+    /*
+     * ========================================================
+     * S1 连击超时处理
+     * ========================================================
+     */
     if(trig1_timeout > 0)
     {
         trig1_timeout--;
     }
-		else if(trig1_timeout==0 && switch1_RELEASE_flag==1 )
+    else if(trig1_timeout == 0 && switch1_RELEASE_flag == 1)
     {
-			switch1_RELEASE_flag=2;
+        switch1_RELEASE_flag = 2;
     }
 
 
-		// 600ms倒计时结束，且有计数
-		if(trig1_timeout == 0 && trig1_cnt == 1 && trig1_wait == 1 && s1_state == DB_PRESSED)		//确定按下1次
+    /*
+     * ========================================================
+     * S1 回弹开关处理
+     * ========================================================
+     */
+    if(trig1_timeout == 0 &&
+       switch1_RELEASE_flag == 2 &&
+       s1_state == DB_IDLE &&
+       s1_return_click_flag == 1)
     {
-				//printf("按下一次 trig1_cnt   %d\r\n",trig1_cnt);
-				trig1_cnt = 0;
-				trig1_wait = 0;
-				s1_first_press_flag=1;
-				xc_gpio_write_pin(GPIO_5,GPIO_PIN_SET);	
-			 flash_ch1_state=xc_gpio_read_pin(GPIO_5);
-			flash_run();
-		
+        if(trig1_cnt == 1 && trig1_wait == 1)
+        {
+            /*
+             * 单击：
+             * GPIO5 翻转。
+             */
+            switch_s1_clear_action_state();
+            switch_s1_output_toggle();
         }
-	
-		else if(trig1_timeout == 0 && (trig1_cnt > 1 && trig1_cnt < TRIGGER_CONTINUE_CNT))
+        else if(trig1_cnt > 1 && trig1_cnt < TRIGGER_CONTINUE_CNT)
         {
-			//	printf("乱按 trig1_cnt   %d\r\n",trig1_cnt);
-			trig1_cnt = 0;
-			trig1_wait = 0;				
-		
-	
-			
+            /*
+             * 2~4 次：
+             * 不动作，但必须彻底清状态。
+             */
+            switch_s1_clear_action_state();
         }
-		else if(trig1_timeout == 0 && trig1_cnt >= TRIGGER_CONTINUE_CNT)
+        else if(trig1_cnt >= TRIGGER_CONTINUE_CNT)
         {
-			//printf("对码 trig1_cnt   %d\r\n",trig1_cnt);
-				if( s1_state == DB_IDLE)
-				{
-					rf433_sw_flag = 2;  // HPW421: S1/GPIO5 is the single relay L2 pairing key
-					trig1_cnt = 0;
-					trig1_wait = 0;	
-				}
-				else
-				{
-					trig1_cnt = 0;
-					trig1_wait = 0;	
-				}	
-		}
-	
-			else if(trig1_timeout == 0 && switch1_RELEASE_flag==2 && s1_state == DB_IDLE && s1_first_press_flag==2 )
-		{			
-			//	printf("低电平 trig2_cnt   %d\r\n",trig2_cnt);
-			s1_state = DB_IDLE;
-			switch1_RELEASE_flag=0;
-			s1_first_press_flag=0;			
-			xc_gpio_write_pin(GPIO_5,GPIO_PIN_RESET);
-			 flash_ch1_state=xc_gpio_read_pin(GPIO_5);
-			flash_run();
-			
-			
-		}
-		
-		
-			
-		
-	 
-	  // S2 超时处理
-    if(trig2_timeout > 0)
-    {
-        trig2_timeout--;
-		}
-		else if(trig2_timeout==0 && switch2_RELEASE_flag==1 )
-		{
-			switch2_RELEASE_flag=2;
-		}
-	
-	
-		// 600ms倒计时结束，且有计数
-		if(trig2_timeout == 0 && trig2_cnt == 1 && trig2_wait == 1 && s2_state == DB_PRESSED)		//确定按下1次
-		{         
-		
-				trig2_cnt = 0;
-				trig2_wait = 0;
-				s2_first_press_flag=1;
-				
-				xc_gpio_write_pin(GPIO_2,GPIO_PIN_SET);	
-			
-			 flash_ch2_state=xc_gpio_read_pin(GPIO_2);
-			flash_run();
-				
-		
-		}
-	
-		else if(trig2_timeout == 0 && (trig2_cnt > 1 && trig2_cnt < TRIGGER_CONTINUE_CNT))
-		{
-			
-			trig2_cnt = 0;
-			trig2_wait = 0;				
-		
-		
-			
-		}
-		else if(trig2_timeout == 0 && trig2_cnt >= TRIGGER_CONTINUE_CNT)
-		{
-			
-			
-				if( s2_state == DB_IDLE)
+            /*
+             * 5 次及以上：
+             * 进入对码。
+             *
+             * 这里增加 s1_pair_invalid_flag 判断。
+             * 正常快速拨动 5 次并最终关闭：进入对码。
+             * 拨动 5 次后停留打开一段时间再关闭：不进入对码。
+             */
+            if(s1_pair_invalid_flag == 0)
             {
                 rf433_sw_flag = 2;
-						trig2_cnt = 0;	
-						trig2_wait = 0;
+            }
+
+            switch_s1_clear_action_state();
         }
         else
         {
-						trig2_cnt = 0;	
-						trig2_wait = 0;
+            /*
+             * 异常兜底清理。
+             */
+            switch_s1_clear_action_state();
         }
-				
-		
     }
-		
-	
-		
-			else if(trig2_timeout == 0 && switch2_RELEASE_flag==2 && s2_state == DB_IDLE && s2_first_press_flag==2 )
+    /*
+     * ========================================================
+     * 普通不回弹开关释放后关闭 GPIO5
+     * ========================================================
+     */
+    else if(trig1_timeout == 0 &&
+            switch1_RELEASE_flag == 2 &&
+            s1_state == DB_IDLE &&
+            s1_first_press_flag == 2)
     {
-			
-			
-			
-			s2_state = DB_IDLE;
-			switch2_RELEASE_flag=0;
-			s2_first_press_flag=0;
-			
-			xc_gpio_write_pin(GPIO_2,GPIO_PIN_RESET);
-			 flash_ch2_state=xc_gpio_read_pin(GPIO_2);
-			flash_run();
+        /*
+         * 普通不回弹开关释放后关闭 GPIO5。
+         */
+        switch_s1_clear_action_state();
+        switch_s1_output_off();
+    }
+    /*
+     * ========================================================
+     * 兜底：2~4 次超时
+     * ========================================================
+     */
+    else if(trig1_timeout == 0 &&
+            trig1_cnt > 1 &&
+            trig1_cnt < TRIGGER_CONTINUE_CNT)
+    {
+        /*
+         * 2~4 次：
+         * 不动作，但是必须清理全部状态。
+         */
+        switch_s1_clear_action_state();
+    }
+    /*
+     * ========================================================
+     * 兜底：5 次及以上超时
+     * ========================================================
+     */
+    else if(trig1_timeout == 0 &&
+            trig1_cnt >= TRIGGER_CONTINUE_CNT &&
+            s1_state == DB_IDLE)
+    {
+        /*
+         * 5 次及以上：
+         *
+         * 这里必须保留对码。
+         * 因为正常快速拨动 5 次后，经常就是走这个兜底分支进入对码。
+         *
+         * 但是增加 s1_pair_invalid_flag 判断：
+         * 如果是“5次后停留打开超过200ms再关闭”，则不允许对码。
+         */
+        if(s1_pair_invalid_flag == 0)
+        {
+            rf433_sw_flag = 2;
         }
 
-		
-		
+        switch_s1_clear_action_state();
+    }
+    /*
+     * ========================================================
+     * 兜底：异常释放状态
+     * ========================================================
+     */
+    else if(trig1_timeout == 0 &&
+            switch1_RELEASE_flag == 2 &&
+            s1_state == DB_IDLE &&
+            trig1_cnt == 0 &&
+            trig1_wait == 0)
+    {
+        /*
+         * 防止残留 switch1_RELEASE_flag == 2。
+         */
+        switch_s1_clear_action_state();
+    }
 }
 
 
+/*
+ * ============================================================
+ * GPIO 中断回调
+ * ============================================================
+ */
 void gpio_intr_callback(uint64_t intr_sta)
 {
-	if((intr_sta & ((uint64_t)1 << SWITCH_S1_PIN)) != 0) 	//如果是GPIO_1的中断 
+    /*
+     * GPIO1 下降沿中断
+     */
+    if((intr_sta & ((uint64_t)1 << SWITCH_S1_PIN)) != 0)
     {
-			 if(s1_state == DB_IDLE && S1_first_on_state==0) // 只有空闲才响应
+        if(s1_state == DB_IDLE && S1_first_on_state == 0)
         {
             s1_state = DB_PRESS_DEBOUNCE;
-            s1_debounce_cnt = DEBOUNCE_MS; // 40ms防抖
-        }
-	}
-	
-	
-		if((intr_sta & ((uint64_t)1 << SWITCH_S2_PIN)) != 0)	//如果是GPIO_19的中断
-		{
-				 if(s2_state == DB_IDLE && S2_first_on_state==0)
-        {
-            s2_state = DB_PRESS_DEBOUNCE;
-            s2_debounce_cnt = DEBOUNCE_MS;
+            s1_debounce_cnt = DEBOUNCE_MS;
         }
     }
 }

project/example/ble/ble_peripheral/app/src/switch_s.h

@@ -1,47 +1,75 @@
 #ifndef __SWITCH_S_H__
 #define __SWITCH_S_H__
 
-
-
-
 #include <stdint.h>
+#include "xc_drv_gpio.h"
 
+/*
+ * ============================================================
+ * 开关检测说明
+ * ============================================================
+ *
+ * 当前版本只保留 S1：
+ *
+ * 输入：
+ *    GPIO1
+ *
+ * 输出：
+ *    GPIO5
+ *
+ * 功能：
+ *
+ * 1. 普通不回弹墙壁开关：
+ *    - GPIO1 按下超过 200ms 不松手：
+ *      GPIO5 打开。
+ *    - GPIO1 释放后：
+ *      GPIO5 关闭。
+ *
+ * 2. 回弹开关：
+ *    - GPIO1 200ms 内按下松开：
+ *      认为是一次回弹点击。
+ *    - 单击 1 次：
+ *      GPIO5 翻转，开变关，关变开。
+ *    - 快速点击 2~4 次：
+ *      不动作。
+ *    - 快速点击 5 次及以上，并且最终释放为关：
+ *      rf433_sw_flag = 2，进入对码。
+ *
+ * 3. 修复点：
+ *    - 对码后彻底清理所有开关状态，避免后续只能开不能关。
+ *    - DB_IDLE 状态增加 GPIO1 低电平补检，避免漏中断。
+ *    - 快速拨动 5 次后如果最后停在打开状态，等一段时间再关，
+ *      不再进入对码。
+ */
 
-// 400ms 超时
+// trigger_check_process() 实际调用周期，单位 ms
+#define SWITCH_SCAN_PERIOD_MS        10
+
+// 连击超时时间：20 * 10ms = 200ms
 #define TRIGGER_TIMEOUT_MS           20
-// 连续触发次数
+
+// 连续触发次数，达到 5 次进入对码
 #define TRIGGER_CONTINUE_CNT         5
 
-#define SWITCH_S1_PIN  GPIO_1
-#define SWITCH_S2_PIN  GPIO_19
+// 回弹开关判断时间：200ms 内松手，认为是回弹开关
+#define RETURN_SWITCH_TIME_MS        200
+#define RETURN_SWITCH_CNT            (RETURN_SWITCH_TIME_MS / SWITCH_SCAN_PERIOD_MS)
 
+// S1 输入引脚
+#define SWITCH_S1_PIN                GPIO_1
 
 // 防抖状态机
 typedef enum {
-    DB_IDLE = 0,      // 空闲，等待下降沿
-    DB_PRESS_DEBOUNCE, // 按下防抖中
-    DB_PRESSED,        // 确认按下，等待释放
-    DB_RELEASE_DEBOUNCE // 释放防抖
+    DB_IDLE = 0,
+    DB_PRESS_DEBOUNCE,
+    DB_PRESSED,
+    DB_RELEASE_DEBOUNCE
 } debounce_state_t;
 
 extern uint8_t rf433_sw_flag;
-
 extern uint8_t S1_first_on_state;
-extern uint8_t S2_first_on_state;
 
 void switch_init(void);
-
 void trigger_check_process(void);
 
-
-
-
-
-
-
-
-
-
-
-
 #endif

project/example/ble/ble_peripheral/mdk/Objects/Xinc_ble_sdk.build_log.htm

@@ -21,8 +21,8 @@ Target DLL:      UL2CM3.DLL V1.164.8.0
 Dialog DLL:      TARMCM1.DLL V1.14.6.0
  
 <h2>Project:</h2>
-C:\Users\QJM\Desktop\6517_SDK\XC6XXX系列SDK_20260428\XC65+XC62系列SDK_20260428\project\example\ble\ble_peripheral\mdk\ble_peripheral.uvprojx
-Project File Date:  07/03/2026
+C:\Users\QJM\Desktop\421发布58兼容两种遥控\project\example\ble\ble_peripheral\mdk\ble_peripheral.uvprojx
+Project File Date:  07/21/2026
 
 <h2>Output:</h2>
 *** Using Compiler 'V5.06 update 7 (build 960)', folder: 'D:\Keil_v5\ARM\ARMCC\Bin'
@@ -34,91 +34,94 @@ compiling app_batt.c...
 compiling arch_main.c...
 ..\app\src\arch_main.c(202): warning:  #177-D: variable "spi_idx"  was declared but never referenced
       uint8_t spi_idx=0;
-..\app\src\arch_main.c(341): warning:  #223-D: function "rf_tx_power_set" declared implicitly
+..\app\src\arch_main.c(340): warning:  #223-D: function "rf_tx_power_set" declared implicitly
       rf_tx_power_set(TRANS_POWER_0_5DBM);
 ..\app\src\arch_main.c: 2 warnings, 0 errors
 compiling app_sec.c...
 compiling usr_server.c...
+..\app\src\usr_server.c(78): warning:  #550-D: variable "ble_state_last_ch1_count"  was set but never used
+  static uint8_t ble_state_last_ch1_count = 0;
+..\app\src\usr_server.c: 1 warning, 0 errors
 compiling aes.c...
 compiling app_task.c...
 compiling xc_drv_adc.c...
 compiling nvds.c...
 compiling xc_drv_aotimer.c...
+compiling xc_drv_bor.c...
 compiling xc_gap_api.c...
 compiling xc_gatt_client_api.c...
-compiling xc_drv_bor.c...
 compiling xc_gatt_server_api.c...
 compiling xc_drv_calib.c...
 compiling xc_drv_dma.c...
 compiling xc_drv_clock.c...
 compiling xc_drv_fmc_spi_dma.c...
 compiling xc_drv_fmc_spi.c...
-compiling xc_drv_gpio.c...
 compiling xc_drv_i2c.c...
+compiling xc_drv_gpio.c...
 compiling xc_drv_pga.c...
 compiling xc_drv_pwm.c...
-compiling xc_drv_pwr.c...
 compiling xc_drv_qdec.c...
+compiling xc_drv_pwr.c...
 compiling xc_drv_rtc.c...
 compiling xc_drv_spi.c...
 compiling xc_drv_spi_dma.c...
 compiling xc_drv_sw_i2c.c...
 compiling xc_drv_systick.c...
 compiling xc_drv_timer.c...
-compiling xc_drv_uart_dma.c...
 compiling xc_drv_uart.c...
+compiling xc_drv_uart_dma.c...
 compiling xc_drv_wdt.c...
 compiling timer.c...
-compiling uart_1.c...
-compiling rf433.c...
-..\app\src\rf433.c(128): warning:  #177-D: function "set_click"  was declared but never referenced
-  static void  set_click(void)
-..\app\src\rf433.c: 1 warning, 0 errors
+compiling switch_s.c...
 compiling fmc_spi_1.c...
 compiling led.c...
-compiling switch_s.c...
-compiling key.c...
 compiling timeslice.c...
-compiling ota_flash_interface.c...
+compiling key.c...
+compiling uart_1.c...
+compiling rf433.c...
+..\app\src\rf433.c(116): warning:  #177-D: function "set_click"  was declared but never referenced
+  static void  set_click(void)
+..\app\src\rf433.c: 1 warning, 0 errors
 compiling rf433_decoder.c...
-compiling ota_server.c...
+compiling ota_flash_interface.c...
 compiling ota_protocol.c...
 ..\app\src\ota_protocol.c(149): warning:  #550-D: variable "sw_ver"  was set but never used
       uint16_t sw_ver;
 ..\app\src\ota_protocol.c(150): warning:  #550-D: variable "rom_ver"  was set but never used
       uint16_t rom_ver;
 ..\app\src\ota_protocol.c: 2 warnings, 0 errors
+compiling ota_server.c...
 linking...
 .\Linker\cpu_xip.scat(21): warning: L6329W: Pattern uread4.o(.text) only matches removed unused sections.
-Program Size: Code=28664 RO-data=1784 RW-data=3000 ZI-data=4192  
+Program Size: Code=28456 RO-data=1784 RW-data=3016 ZI-data=4192  
 Finished: 0 information, 1 warning and 0 error messages.
 After Build - User command #1: fromelf --bin --output=app.bin .\Objects\Xinc_ble_sdk.axf
 After Build - User command #2: .\output_tool\Double_ota\ge_ota.bat
-Size of file: 30568 bytes.
-all_size=30568
-size:30568 PageCNT120
+Size of file: 30368 bytes.
+all_size=30368
+size:30368 PageCNT119
 dual_xip
-length:30984
-size:30984
+length:30728
+size:30728
 Addr:12000
-            Size:0x7800
+            Size:0x7700
             BAddr:0x12000
-            Acheck:0x8ed9ea0
+            Acheck:0x21e62240
             SoftVer:0x10
             RomVer:0x20
             LoadAddr:0x11012000
             Is xip ota?:1
 ota_data.bin success已复制         1 个文件。
-Size of file: 30568 bytes.
-all_size=30568
-size:30568 PageCNT120
+Size of file: 30368 bytes.
+all_size=30368
+size:30368 PageCNT119
 dual_xip
-length:30984
-size:30984
+length:30728
+size:30728
 Addr:12000
-            Size:0x7800
+            Size:0x7700
             BAddr:0x1e000
-            Acheck:0x8ed9ea0
+            Acheck:0x21e62240
             SoftVer:0x10
             RomVer:0x20
             LoadAddr:0x11012000
@@ -152,10 +155,440 @@ is_db=1
 is_th=0
 需要填充0个sector
 all_size:1a000
-size: 30568
+size: 30368
 updata file success !
 已复制         1 个文件。
-".\Objects\Xinc_ble_sdk.axf" - 0 Error(s), 6 Warning(s).
+总有2个命令行参数
+可 执 行文 件 名:C:\Users\QJM\Desktop\421发布58兼容两种遥控\tools\offline_burn\Xinc_mac_tool.exe
+第一个命令行参数:40-ab-00-cd-01-01
+第二个命令行参数:1000000
+限制烧录次数burn_times=1000000
+mac:40-ab-00-cd-01-01
+0X40 0XAB 0 0XCD 0X1 0X1 
+Size of file: 106496 bytes.
+crc:1:f4cf18e0
+crc:2:8fddd820
+crc:3:481623e0
+crc:4:d6120320
+crc:5:36e1e360
+crc:6:3faa39c0
+crc:7:5f951c60
+crc:8:25b14e0
+crc:9:a2fbe460
+crc:10:71af8e0
+crc:11:ba65bd20
+crc:12:2fb17760
+crc:13:416afca0
+crc:14:e1270f60
+crc:15:246e13c0
+crc:16:7f67c320
+crc:17:1946dba0
+crc:18:2105cfe0
+crc:19:a79444e0
+crc:20:74a721a0
+crc:21:11d3fd00
+crc:22:d2b1dd80
+crc:23:73d8380
+crc:24:8d093260
+crc:25:9aaaec0
+crc:26:c6f0eb20
+crc:27:25ecd560
+crc:28:57384220
+crc:29:b08b2bc0
+crc:30:5dd40500
+crc:31:b2d345c0
+crc:32:35241b80
+crc:33:caf9a220
+crc:34:4811f7e0
+crc:35:760e56e0
+crc:36:fe5caee0
+crc:37:9096fd00
+crc:38:2cae7660
+crc:39:b60a5900
+crc:40:548ad6c0
+crc:41:8b6eafa0
+crc:42:f28bd0e0
+crc:43:d17f94a0
+crc:44:de59a2c0
+crc:45:73193080
+crc:46:d8da74a0
+crc:47:4c632020
+crc:48:66695b00
+crc:49:d76df9a0
+crc:50:23a62e0
+crc:51:93c10ba0
+crc:52:964f3c80
+crc:53:7fb6c120
+crc:54:d6107500
+crc:55:ed2b0960
+crc:56:f5764860
+crc:57:40fc3220
+crc:58:417f8300
+crc:59:8c0de520
+crc:60:ee46dbc0
+crc:61:9e85c540
+crc:62:c87b9c40
+crc:63:6ba3760
+crc:64:e7ac58a0
+crc:65:eca7ba0
+crc:66:54d67d40
+crc:67:4b6989e0
+crc:68:5d052240
+crc:69:78b9c760
+crc:70:23c42fe0
+crc:71:a95fbd00
+crc:72:dd9fa100
+crc:73:d4d2dca0
+crc:74:898379e0
+crc:75:3e2171a0
+crc:76:d05fbdc0
+crc:77:b55abc0
+crc:78:bf93d1c0
+crc:79:c21b1160
+crc:80:6a33c220
+crc:81:e6c64a60
+crc:82:4646c100
+crc:83:13fe54c0
+crc:84:62301960
+crc:85:536f3040
+crc:86:dbb13220
+crc:87:db527e80
+crc:88:225fd560
+crc:89:c1404a40
+crc:90:6988dca0
+crc:91:38527fc0
+crc:92:559ff600
+crc:93:3eb92f80
+crc:94:7dfc6e00
+crc:95:50e440a0
+crc:96:81ae8760
+crc:97:a5fb6f80
+crc:98:e245bc20
+crc:99:3fe0c960
+crc:100:57890aa0
+crc:101:33c0b760
+crc:102:d1ec1d20
+crc:103:d76feb20
+crc:104:ac2c800
+crc:105:fa858ca0
+crc:106:db8ff560
+crc:107:697479e0
+crc:108:4e57c7e0
+crc:109:3746aac0
+crc:110:5af187a0
+crc:111:7fdc0820
+crc:112:df356a80
+crc:113:45167a0
+crc:114:f0b85520
+crc:115:ed30b580
+crc:116:9c166240
+crc:117:46048720
+crc:118:488ae100
+crc:119:4f508200
+crc:120:5ad6bd00
+crc:121:6d9de7c0
+crc:122:12e49340
+crc:123:c8115e80
+crc:124:29e709a0
+crc:125:54bef0a0
+crc:126:f7e21c20
+crc:127:89e00720
+crc:128:4b140
+crc:129:d52f90c0
+crc:130:38d12ec0
+crc:131:39cc5680
+crc:132:85a77a40
+crc:133:996662e0
+crc:134:bbeca6e0
+crc:135:5cf67420
+crc:136:99ce0700
+crc:137:cfbd25c0
+crc:138:548176e0
+crc:139:f7799d00
+crc:140:5f660080
+crc:141:f0c64ec0
+crc:142:86f6bb00
+crc:143:2f3628a0
+crc:144:f056f820
+crc:145:417b1460
+crc:146:52aa4360
+crc:147:7f2402e0
+crc:148:c193a040
+crc:149:bd761120
+crc:150:1e1cf880
+crc:151:94606b40
+crc:152:815c8960
+crc:153:1ef41580
+crc:154:f3800680
+crc:155:6295cd80
+crc:156:9075db00
+crc:157:b6165500
+crc:158:47e725a0
+crc:159:7a5e3d40
+crc:160:c5577640
+crc:161:f546bcc0
+crc:162:67d4a860
+crc:163:cd28b4c0
+crc:164:45898860
+crc:165:ae2819a0
+crc:166:b79dd2e0
+crc:167:f489f240
+crc:168:df61c740
+crc:169:ae51ac40
+crc:170:459d15e0
+crc:171:c8af6bc0
+crc:172:d6b41aa0
+crc:173:ce9fdde0
+crc:174:72dbb600
+crc:175:6232bae0
+crc:176:f58c59e0
+crc:177:47438c20
+crc:178:78dd88e0
+crc:179:3bc755e0
+crc:180:cf10e980
+crc:181:6e6153e0
+crc:182:1ffbbbc0
+crc:183:9238a3c0
+crc:184:3071fac0
+crc:185:1614fda0
+crc:186:b9fbc300
+crc:187:61485ac0
+crc:188:d4162060
+crc:189:c289f360
+crc:190:5fa88860
+crc:191:2c0f4640
+crc:192:13002dc0
+crc:193:ecafbb00
+crc:194:6be8cde0
+crc:195:80b01920
+crc:196:74245ea0
+crc:197:d62fd620
+crc:198:e48febe0
+crc:199:31b28880
+crc:200:587ec140
+crc:201:39f67920
+crc:202:1328aa40
+crc:203:c2770ca0
+crc:204:678bb340
+crc:205:7e9dc6c0
+crc:206:ad3b1b80
+crc:207:3a7b88e0
+crc:208:78c43720
+crc:209:fbacbe80
+crc:210:7d88cc00
+crc:211:fee53700
+crc:212:ffbe6240
+crc:213:f487ea60
+crc:214:104e5c00
+crc:215:afb84840
+crc:216:20082cc0
+crc:217:89935020
+crc:218:662b46a0
+crc:219:17ce8a00
+crc:220:b0906840
+crc:221:1e2171a0
+crc:222:82e97380
+crc:223:9746b680
+crc:224:c0748fe0
+crc:225:fe938d60
+crc:226:25504640
+crc:227:efe909a0
+crc:228:319f2600
+crc:229:25e9bfe0
+crc:230:3c802800
+crc:231:470b0a00
+crc:232:fb95bf20
+crc:233:caaaaac0
+crc:234:fdef3ea0
+crc:235:8d7aaea0
+crc:236:fc99d20
+crc:237:93f98240
+crc:238:6d5b5880
+crc:239:3f057f80
+crc:240:6bd740a0
+crc:241:7ed04080
+crc:242:aadbca0
+crc:243:2b1b600
+crc:244:d7875260
+crc:245:e0477fa0
+crc:246:28aa0280
+crc:247:19ad47e0
+crc:248:246ce200
+crc:249:e5336d60
+crc:250:c890ae20
+crc:251:fe426cc0
+crc:252:2cad39c0
+crc:253:29967280
+crc:254:6504de80
+crc:255:469509e0
+crc:256:1d5f4ce0
+crc:257:c08f7fc0
+crc:258:af5a6a0
+crc:259:c2da6260
+crc:260:c598a440
+crc:261:938c2b20
+crc:262:e68bc0e0
+crc:263:a539f940
+crc:264:36525220
+crc:265:fa4db8a0
+crc:266:200e0ae0
+crc:267:e5c16280
+crc:268:539f27c0
+crc:269:b1cd6900
+crc:270:46abe5c0
+crc:271:677e3800
+crc:272:ee804420
+crc:273:2a6ad2a0
+crc:274:7f51a1c0
+crc:275:393f7ea0
+crc:276:8e4e6680
+crc:277:bfe05480
+crc:278:26085340
+crc:279:f6b6c0e0
+crc:280:e4bc0360
+crc:281:7e0b9f60
+crc:282:d0f2da20
+crc:283:f2afb8c0
+crc:284:a56c76c0
+crc:285:2e5e6880
+crc:286:c5faf120
+crc:287:a8dd78c0
+crc:288:1000fca0
+crc:289:473d920
+crc:290:cbdcd5e0
+crc:291:e994f120
+crc:292:7bec0380
+crc:293:189ecea0
+crc:294:31b6f080
+crc:295:b5a84fc0
+crc:296:2270680
+crc:297:29c1f260
+crc:298:8e157300
+crc:299:bed38ec0
+crc:300:c9ac64a0
+crc:301:366bb540
+crc:302:7e5c34c0
+crc:303:2abe5660
+crc:304:99dd2ba0
+crc:305:eec6e920
+crc:306:259991a0
+crc:307:801903e0
+crc:308:4b6a4520
+crc:309:d99b8740
+crc:310:dd845d60
+crc:311:c6f0edc0
+crc:312:d80b8fe0
+crc:313:d833f560
+crc:314:96bd6a60
+crc:315:88cceb20
+crc:316:43d3a9c0
+crc:317:7a38df80
+crc:318:fc744c0
+crc:319:b15e7ea0
+crc:320:96870540
+crc:321:cfa02dc0
+crc:322:c38c2c80
+crc:323:fb416440
+crc:324:fdcff660
+crc:325:ffa044c0
+crc:326:44000ce0
+crc:327:bdcc1ae0
+crc:328:6924f0a0
+crc:329:19858380
+crc:330:5d78b7c0
+crc:331:756a43c0
+crc:332:ca474d80
+crc:333:625b23c0
+crc:334:98f60040
+crc:335:244bf920
+crc:336:12f64cc0
+crc:337:69e55020
+crc:338:2f2e1e40
+crc:339:aa025cc0
+crc:340:23031ec0
+crc:341:33fda400
+crc:342:bcfa3300
+crc:343:bf95b840
+crc:344:84ddc760
+crc:345:538d8580
+crc:346:bcb51720
+crc:347:f3abc820
+crc:348:f1b137e0
+crc:349:4c15c420
+crc:350:ae0825a0
+crc:351:e0cc3640
+crc:352:ab8dee80
+crc:353:f21cc5a0
+crc:354:82375ba0
+crc:355:e3532440
+crc:356:fd119e40
+crc:357:b6b8ccc0
+crc:358:1d0be220
+crc:359:5ec9fc60
+crc:360:29dda300
+crc:361:6971e3e0
+crc:362:243e3be0
+crc:363:eab8cca0
+crc:364:d43e8120
+crc:365:19fc9e80
+crc:366:f21d3980
+crc:367:691221c0
+crc:368:4b291440
+crc:369:7df61720
+crc:370:ad9aeac0
+crc:371:23f0f3c0
+crc:372:e4039100
+crc:373:a67190c0
+crc:374:c7ec2860
+crc:375:4f60c3e0
+crc:376:a49183e0
+crc:377:ba90db80
+crc:378:bee37560
+crc:379:76c755c0
+crc:380:2968c780
+crc:381:57a99840
+crc:382:90bb99e0
+crc:383:db700800
+crc:384:57d6ba20
+crc:385:fc8581c0
+crc:386:4d3b40
+crc:387:e2c8f0a0
+crc:388:cd09d080
+crc:389:b3541400
+crc:390:ef541da0
+crc:391:876504c0
+crc:392:ffd09800
+crc:393:1dbef980
+crc:394:c6c85740
+crc:395:af76bce0
+crc:396:76538ca0
+crc:397:91e60a60
+crc:398:698e0280
+crc:399:34399e80
+crc:400:7f978f00
+crc:401:fa26d6c0
+crc:402:b6a12140
+crc:403:1b39dc20
+crc:404:5f86d180
+crc:405:27b710c0
+crc:406:b3fb8b60
+crc:407:c9e121e0
+crc:408:7b6732e0
+crc:409:78e37d40
+crc:410:6046e0
+crc:411:fc3f7fa0
+crc:412:17b44fe0
+crc:413:3728d240
+crc:414:b7a4a8e0
+crc:415:df464f60
+PageCNT:416remain:256file_sumcheck:df464f60 i:416
+length:1a000
+00 106496updata mac success !
+merge file success !
+Checksum source: C:\Users\QJM\Desktop\421发布58兼容两种遥控\tools\offline_burn\40-ab-00-cd-01-01_DF464F60_1000000.bin
+Online BIN: C:\Users\QJM\Desktop\421发布58兼容两种遥控\release\online\HPW421_V1.3_XC6517_DF464F60.bin
+OTA BIN: C:\Users\QJM\Desktop\421发布58兼容两种遥控\release\ota\HPW421_V1.3_XC6517_DF464F60_OTA.bin
+".\Objects\Xinc_ble_sdk.axf" - 0 Error(s), 7 Warning(s).
 
 <h2>Software Packages used:</h2>
 
@@ -168,7 +601,7 @@ Package Vendor: ARM
   D:/Keil_v5/Packs/ARM/CMSIS/5.9.0/Device/ARM/ARMCM0/Include
 
 <h2>Collection of Component Files used:</h2>
-Build Time Elapsed:  00:00:22
+Build Time Elapsed:  00:00:20
 </pre>
 </body>
 </html>

project/example/ble/ble_peripheral/mdk/Objects/rf433.d

@@ -75,3 +75,64 @@
 .\objects\rf433.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_swdiag.h
 .\objects\rf433.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_trc.h
 .\objects\rf433.o: ..\app\src\rf433_decoder.h
+.\objects\rf433.o: ..\app\src\usr_server.h
+.\objects\rf433.o: ..\app\api\app_task.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gap\gapm\gapm_int.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_task.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gap.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
+.\objects\rf433.o: D:\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_hci.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_error.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_list.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_task.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\ll\gnuarm\ll.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\reg_intc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_intc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\driver\reg\reg_access.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\em\api\em_map.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_math.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_et.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\em_map_ble.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_llcp.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_cs.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_tx_desc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_rx_desc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_rx_cte_desc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_wpal.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_ral.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_msg_int.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_buf.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_mem.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gap_api.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapc_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\nvds\api\nvds.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gatt_server_api.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_db.h

project/example/ble/ble_peripheral/mdk/Objects/timeslice.d

@@ -7,11 +7,10 @@
 .\objects\timeslice.o: ..\app\src\rf433.h
 .\objects\timeslice.o: ..\app\src\key.h
 .\objects\timeslice.o: ..\app\src\switch_s.h
-.\objects\timeslice.o: ..\app\src\ota_flash_interface.h
-.\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h
+.\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_gpio.h
+.\objects\timeslice.o: D:\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc65xx.h
-.\objects\timeslice.o: D:\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -64,6 +63,8 @@
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_adc.h
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwm.h
 .\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_bor.h
+.\objects\timeslice.o: ..\app\src\ota_flash_interface.h
+.\objects\timeslice.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h
 .\objects\timeslice.o: ..\app\src\ota_protocol.h
 .\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
 .\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
@@ -104,3 +105,36 @@
 .\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_wpal.h
 .\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_ral.h
 .\objects\timeslice.o: ..\app\src\rf433_decoder.h
+.\objects\timeslice.o: ..\app\src\usr_server.h
+.\objects\timeslice.o: ..\app\api\app_task.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_swdiag.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_trc.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gap\gapm\gapm_int.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm_msg.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_task.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gap.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\common\api\co_list.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_task.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_msg.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_msg_int.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt_msg.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap_msg.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\common\api\co_buf.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_mem.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gap_api.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapc_msg.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\modules\nvds\api\nvds.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gatt_server_api.h
+.\objects\timeslice.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_db.h

project/example/ble/ble_peripheral/mdk/Objects/uart_1.d

@@ -60,3 +60,74 @@
 .\objects\uart_1.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwm.h
 .\objects\uart_1.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_bor.h
 .\objects\uart_1.o: ..\app\src\rf433.h
+.\objects\uart_1.o: ..\app\src\usr_server.h
+.\objects\uart_1.o: ..\app\api\app_task.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\rwble_hl_error.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
+.\objects\uart_1.o: ..\app\api\rwapp_config.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_swdiag.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_trc.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gap\gapm\gapm_int.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm_msg.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_task.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gap.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
+.\objects\uart_1.o: D:\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_hci.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_error.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_list.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_task.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_msg.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\ll\gnuarm\ll.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\reg_intc.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_intc.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\driver\reg\reg_access.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\em\api\em_map.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_math.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_et.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\em_map_ble.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_llcp.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_cs.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_tx_desc.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_rx_desc.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_rx_cte_desc.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_wpal.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_ral.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_msg_int.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt_msg.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap_msg.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\common\api\co_buf.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_mem.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gap_api.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapc_msg.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\modules\nvds\api\nvds.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gatt_server_api.h
+.\objects\uart_1.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_db.h

project/example/ble/ble_peripheral/mdk/Objects/usr_server.d

@@ -129,3 +129,4 @@
 .\objects\usr_server.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gatt_server_api.h
 .\objects\usr_server.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_db.h
 .\objects\usr_server.o: ..\app\src\uart_1.h
+.\objects\usr_server.o: ..\app\src\rf433.h