清理在线发布文件并恢复PWM32EPRO型号

This reverts commit 550d0987ea.

.gitignore

@@ -0,0 +1,6 @@
+project/example/ble/ble_peripheral/mdk/codex_build.log
+release/ble_peripheral.bin
+release/online/*.bin
+release/ota/*.bin
+tools/offline_burn/download.bin
+tools/offline_burn/40-ab-00-cd-01-01_*_1000000.bin

Document/12-24V_2P2N双色LED_H桥驱动原理与器件设计.md

@@ -0,0 +1,779 @@
+# 12～24V 2P2N双色LED H桥驱动原理与器件设计
+
+## 1. 文档目的
+
+本文针对一套输入电压为12～24V的双色LED H桥驱动电路。主功率桥由2只PMOS和2只NMOS组成，另外使用2只小信号NMOS驱动高边PMOS，因此整个驱动部分共使用6只MOS管。
+
+本文说明：
+
+- 2P2N主桥和2只驱动MOS分别承担什么工作；
+- 双色LED为什么需要H桥改变电流方向；
+- 两路PWM输入怎样控制暖光、冷光和关闭状态；
+- 为什么两路输入绝对不能同时为高电平；
+- 为什么换向必须先输出`00`并保留死区；
+- PMOS为什么需要栅极上拉电阻和下拉电阻；
+- 两个电阻为什么会形成分压；
+- 电阻太大或太小分别会产生什么问题；
+- 12V稳压管在电路中起什么作用；
+- 如何计算PMOS的栅源电压、电阻功耗和稳压管电流；
+- 如果取消稳压管，应当如何重新选择电阻；
+- 为什么还必须检查死区时间、MOS管尖峰和PCB布局。
+
+本文尽量使用直观的方式说明，适合刚接触MOS管驱动电路的工程人员阅读。
+
+---
+
+## 2. 完整电路由哪些部分组成
+
+![12～24V 2P2N双色LED H桥驱动原理图](images/12-24V_2P2N_H桥驱动原理图.png)
+
+图1：本项目12～24V、2P2N主桥加2只小MOS驱动的完整原理图。
+
+图中的主要器件分工如下：
+
+| 器件 | 类型 | 作用 |
+|---|---|---|
+| Q1、Q2 | 高边PMOS（60P03） | 分别把C端、W端连接到12～24V电源 |
+| Q9、Q10 | 低边NMOS（60N03） | 分别把C端、W端连接到GND |
+| Q7、Q8 | 小信号NMOS（AO3400A） | 分别下拉Q1、Q2的栅极 |
+| R1、R2 | 2.4kΩ上拉电阻 | 使Q1、Q2快速关断 |
+| R3、R4 | 3kΩ下拉通路电阻 | 与R1、R2分压，限制高边PMOS的导通VGS |
+| D1、D2 | 12V稳压管（BZT52C12） | 限制高边PMOS的栅源电压尖峰 |
+| R14、R15 | 10kΩ栅源下拉电阻 | 确保Q9、Q10在控制信号悬空时保持关闭 |
+
+### 2.1 2只高边PMOS
+
+高边使用2只PMOS：
+
+- 左侧PMOS负责把输出端`C`连接到12～24V电源；
+- 右侧PMOS负责把输出端`W`连接到12～24V电源。
+
+PMOS适合放在高边，是因为它的源极可以直接接正电源，栅极只需要从源极电压向下拉，就能导通。
+
+### 2.2 2只低边NMOS
+
+低边使用2只NMOS：
+
+- 左侧NMOS负责把输出端`C`连接到GND；
+- 右侧NMOS负责把输出端`W`连接到GND。
+
+低边NMOS的源极接地，MCU输出高电平后比较容易直接驱动其栅极。
+
+### 2.3 2只PMOS驱动NMOS
+
+MCU通常只有3.3V输出，不能直接把接在12～24V电源上的PMOS栅极拉到合适电位，所以增加2只小信号NMOS：
+
+- 左侧驱动NMOS负责下拉左侧PMOS栅极；
+- 右侧驱动NMOS负责下拉右侧PMOS栅极。
+
+这2只小MOS不直接承受LED主电流，只负责PMOS栅极的充电和放电控制。
+
+### 2.4 负载是反向并联双色LED
+
+双色LED连接在`C`、`W`两个H桥输出端之间。两种颜色的LED芯片方向相反：
+
+- 电流从`C`流向`W`时，点亮一种颜色；
+- 电流从`W`流向`C`时，点亮另一种颜色；
+- 两个方向快速分时工作时，肉眼看到混合色或中性光。
+
+H桥的作用不是简单提供两路独立正电压，而是改变流过双色LED的电流方向。
+
+---
+
+## 3. 两路输入如何控制H桥
+
+本文把两路控制信号称为：
+
+- `PWM_W`：驱动Q7和对角线上的Q10，形成`C→W`电流；
+- `PWM_C`：驱动Q8和对角线上的Q9，形成`W→C`电流。
+
+按照当前交叉驱动结构，一路信号会同时控制一只高边PMOS和对角线上的一只低边NMOS。
+
+> `PWM_C`、`PWM_W`是电路网络名称。最终点亮暖色还是冷色，还取决于双色LED的实际安装方向。
+
+### 3.1 PWM_W有效
+
+`PWM_W=1、PWM_C=0`时：
+
+- Q7导通并下拉Q1的栅极，使左侧高边PMOS Q1导通；
+- 对角线上的右侧低边NMOS Q10导通；
+- `C`端接近电源；
+- `W`端接近GND；
+- 电流方向为`电源 → C → LED → W → GND`。
+
+此时点亮一个颜色。
+
+### 3.2 PWM_C有效
+
+`PWM_C=1、PWM_W=0`时：
+
+- Q8导通并下拉Q2的栅极，使右侧高边PMOS Q2导通；
+- 对角线上的左侧低边NMOS Q9导通；
+- `W`端接近电源；
+- `C`端接近GND；
+- 电流方向为`电源 → W → LED → C → GND`。
+
+此时点亮另一个颜色。
+
+### 3.3 两路均为低电平
+
+`PWM_C=0、PWM_W=0`时：
+
+- 两只高边PMOS关闭；
+- 两只低边NMOS关闭；
+- H桥处于关闭状态；
+- LED没有持续驱动电流。
+
+换向时必须先进入这个状态。
+
+### 3.4 两路均为高电平
+
+`PWM_C=1、PWM_W=1`是禁止状态。
+
+此时两组对角桥臂同时收到导通命令，可能导致同一桥臂的上管和下管同时导通，形成：
+
+```text
+电源 → 上管 → 下管 → GND
+```
+
+这条路径几乎没有LED负载限流，会产生很大的直通电流，可能造成：
+
+- 电源异响；
+- MOS管快速发热；
+- 电源电压跌落；
+- MCU复位或蓝牙掉线；
+- MOS管损坏；
+- PCB走线或电源器件损坏。
+
+控制真值表如下：
+
+| PWM_C | PWM_W | H桥状态 | 结果 |
+|---:|---:|---|---|
+| 0 | 0 | 全部关闭 | 安全关闭/换向死区 |
+| 0 | 1 | C高、W低 | 电流从C流向W |
+| 1 | 0 | W高、C低 | 电流从W流向C |
+| 1 | 1 | 禁止状态 | 可能发生桥臂直通 |
+
+---
+
+## 4. 为什么换向必须设置死区
+
+MOS管不是收到控制电平后立即完成导通或关断。栅极电容、米勒平台、驱动电阻和PCB寄生参数都会产生延迟。
+
+如果直接执行：
+
+```text
+PWM_C有效 → PWM_W有效
+```
+
+可能出现：
+
+- 原方向的PMOS和NMOS还没有完全关闭；
+- 新方向的PMOS和NMOS已经开始导通；
+- 两个方向在很短时间内重叠；
+- H桥形成瞬间直通。
+
+正确换向顺序应为：
+
+```text
+方向C导通 → 输出00 → 等待死区 → 方向W导通
+方向W导通 → 输出00 → 等待死区 → 方向C导通
+```
+
+死区时间不能只根据软件定时值决定，必须结合实际MOS管栅极波形测量。对于本类低频LED PWM，可以先设置较保守的死区进行验证，再根据示波器结果缩短。
+
+需要注意：
+
+- 死区太短，可能发生直通；
+- 死区太长，会降低最大有效占空比和LED峰值亮度；
+- 调高PWM频率后，相同死区占整个周期的比例会变大；
+- PMOS上拉电阻变大后，通常需要重新确认死区是否足够。
+
+---
+
+## 5. 先认识PMOS的三个引脚
+
+PMOS有三个主要引脚：
+
+- `S`：源极（Source），本电路接12V或24V电源；
+- `G`：栅极（Gate），用于控制PMOS导通和关断；
+- `D`：漏极（Drain），连接H桥输出端。
+
+PMOS是否导通，主要取决于栅源电压：
+
+```text
+VGS = VG - VS
+```
+
+其中：
+
+- `VG`是栅极对地电压；
+- `VS`是源极对地电压。
+
+假设源极接24V：
+
+| 栅极电压VG | 栅源电压VGS | PMOS状态 |
+|---:|---:|---|
+| 24V | 0V | 关断 |
+| 20V | -4V | 开始较明显导通 |
+| 14V | -10V | 充分导通 |
+| 12V | -12V | 充分导通 |
+| 0V | -24V | 超过多数PMOS的栅源耐压，危险 |
+
+> 注意：数据手册中的`VGS(th)`是“刚开始有很小电流”的开启阈值，不代表MOS管已经充分导通。
+
+以SL60P03D为例：
+
+- `VGS(th)`约为-1.0V至-2.2V；
+- 导通电阻通常在`VGS=-4.5V`或`VGS=-10V`条件下标定；
+- 栅源极绝对最大耐压为`±20V`。
+
+所以“20V”不是开启阈值，而是不能超过的栅源极极限耐压。
+
+---
+
+## 6. 上拉电阻和下拉电阻分别做什么
+
+为避免受到原理图位号差异影响，本文统一使用下面的名称：
+
+- `RUP`：PMOS栅极到源极（电源）的上拉电阻；
+- `RDOWN`：PMOS栅极到地的下拉电阻；
+- `DZ`：跨接在PMOS栅极和源极之间的稳压管；
+- `QDRV`：把PMOS栅极向地拉低的小信号MOS管。
+
+简化结构如下：
+
+```text
+                电源12V/24V
+                     |
+                     +--------- PMOS源极S
+                     |
+                    RUP
+                     |
+                     +--------- PMOS栅极G
+                     |
+                   RDOWN
+                     |
+                   QDRV
+                     |
+                    GND
+
+DZ稳压管跨接在PMOS的S和G之间。
+```
+
+### 6.1 PMOS关断过程
+
+当`QDRV`关闭后，下拉路径断开，`RUP`把PMOS栅极充电到源极电压：
+
+```text
+VG ≈ VS
+VGS ≈ 0V
+```
+
+PMOS关断。
+
+因此，`RUP`越小，给栅极电容充电的电流越大，PMOS通常关断得越快。
+
+### 6.2 PMOS导通过程
+
+当`QDRV`导通后，`RUP`和`RDOWN`形成从电源到地的分压回路，栅极电压下降，PMOS得到负的`VGS`并导通。
+
+因此：
+
+- `RUP`太小：关断快，但栅极不容易被拉低，PMOS导通电压可能不足；
+- `RUP`太大：PMOS容易得到较大的负`VGS`，但栅极充电慢，关断时间增加；
+- `RDOWN`太小：PMOS导通更充分，但电流和电阻功耗增加；
+- `RDOWN`太大：功耗降低，但PMOS导通电压减小。
+
+两个电阻必须综合考虑，不能只追求其中一个方向。
+
+---
+
+## 7. 没有稳压管时如何计算
+
+先忽略稳压管，假设`QDRV`已经完全导通。
+
+栅极电压为：
+
+```text
+VG = VCC × RDOWN / (RUP + RDOWN)
+```
+
+PMOS栅源电压的绝对值为：
+
+```text
+|VGS| = VCC × RUP / (RUP + RDOWN)
+```
+
+回路电流为：
+
+```text
+I = VCC / (RUP + RDOWN)
+```
+
+两个电阻的功耗分别为：
+
+```text
+PUP   = I² × RUP
+PDOWN = I² × RDOWN
+```
+
+### 7.1 当前原理图：24V、上拉2.4kΩ、下拉3kΩ
+
+```text
+VCC   = 24V
+RUP   = 2.4kΩ
+RDOWN = 3kΩ
+```
+
+计算结果：
+
+```text
+VG    = 24 × 3 / (2.4 + 3) ≈ 13.33V
+VGS   = 13.33 - 24 ≈ -10.67V
+I     = 24 / 5.4k ≈ 4.44mA
+PUP   = I² × 2.4k ≈ 47mW
+PDOWN = I² × 3k ≈ 59mW
+```
+
+所以栅极并不会被拉到0V，而是被两个电阻分压到约13.33V。
+
+PMOS得到约-10.67V的栅源电压，能够充分导通。这个数值没有达到12V稳压管的击穿电压，因此D1/D2在稳定导通状态下基本不工作，主要用于处理换向尖峰。
+
+### 7.2 当前原理图：12V、上拉2.4kΩ、下拉3kΩ
+
+同样的电阻在12V输入下：
+
+```text
+VG    = 12 × 3 / (2.4 + 3) ≈ 6.67V
+VGS   = 6.67 - 12 ≈ -5.33V
+I     = 12 / 5.4k ≈ 2.22mA
+PUP   ≈ 12mW
+PDOWN ≈ 15mW
+```
+
+此时PMOS仍然可以可靠导通，而且12V稳压管在正常稳定状态下不会反向击穿。
+
+---
+
+## 8. 稳压管的真正作用
+
+12V稳压管跨接在PMOS的源极和栅极之间，主要作用是限制`|VGS|`。
+
+### 8.1 正常关断时
+
+PMOS栅极被`RUP`拉到源极电压：
+
+```text
+VGS ≈ 0V
+```
+
+稳压管不工作。
+
+### 8.2 正常导通时
+
+栅极被下拉，`|VGS|`逐渐增大。
+
+当`|VGS|`接近稳压管的击穿电压后，稳压管开始反向导通，把`|VGS|`限制在大约12V附近。
+
+24V输入、12V稳压管钳位时，理想状态约为：
+
+```text
+VS  ≈ 24V
+VG  ≈ 12V
+VGS ≈ -12V
+```
+
+### 8.3 换向尖峰出现时
+
+H桥换向会受到以下因素影响：
+
+- MOS管栅极电容；
+- 米勒电容；
+- PCB走线电感；
+- LED和供电线路电感；
+- MOS管体二极管反向恢复；
+- 电源母线尖峰。
+
+这些因素可能让`VGS`在很短时间内超过正常分压值。稳压管可以吸收部分栅源尖峰，避免PMOS栅极氧化层承受过高电压。
+
+### 8.4 正向栅源尖峰
+
+如果换向时栅极瞬间高于源极，稳压管会像普通二极管一样正向导通，把正向`VGS`限制在约0.7V至1V附近。
+
+### 8.5 稳压管不能保护什么
+
+栅源稳压管只能保护PMOS的`VGS`，不能保护PMOS的漏源极`VDS`。
+
+例如：
+
+- 电源为24V；
+- PMOS的`VDS`额定值为-30V。
+
+这时漏源极只有约6V的理论尖峰余量。电源母线仍需考虑：
+
+- TVS管；
+- 就近低ESR电容；
+- 较短、较宽的功率走线；
+- 减小H桥电流环路面积；
+- 必要时使用耐压更高的MOS管。
+
+---
+
+## 9. 为什么稳压管不是接上就一定能稳定在12V
+
+稳压管必须获得足够的反向电流，才能进入比较稳定的击穿区。
+
+为了说明稳压管为什么需要足够电流，下面使用“上拉1.2kΩ、下拉1kΩ”作为对比算例。这不是图1当前采用的2.4kΩ、3kΩ参数。
+
+假设：
+
+```text
+VCC   = 24V
+VZ    = 12V
+RUP   = 1.2kΩ
+RDOWN = 1kΩ
+```
+
+钳位后栅极约为12V。
+
+下拉电阻电流：
+
+```text
+IDOWN = 12V / 1kΩ = 12mA
+```
+
+上拉电阻电流：
+
+```text
+IUP = (24V - 12V) / 1.2kΩ = 10mA
+```
+
+稳压管电流约为：
+
+```text
+IZ = IDOWN - IUP = 12mA - 10mA = 2mA
+```
+
+因此，1.2kΩ上拉加1kΩ下拉时，稳压管大约只有2mA电流。
+
+这通常可以产生一定的钳位作用，但实际电压未必正好是12.00V。稳压管的标称电压、测试电流、动态电阻和温度特性需要查看具体厂家的数据手册。
+
+如果上拉和下拉都是1kΩ：
+
+```text
+IUP   = 12mA
+IDOWN = 12mA
+IZ    ≈ 0mA
+```
+
+此时稳压管几乎没有剩余电流，不能指望它进入稳定的反向击穿状态。
+
+对于图1当前的2.4kΩ上拉和3kΩ下拉，在24V正常导通时，计算得到`|VGS|≈10.67V`，低于12V，因此稳压管不会持续击穿。这正是更合适的状态：正常工作由电阻分压确定栅极电压，稳压管只处理异常瞬态。
+
+---
+
+## 10. 为什么电阻不能只考虑关断速度
+
+MOS管的栅极不是普通的纯电阻负载，可以把它理解为一个需要充电和放电的电容。
+
+SL60P03D的典型参数包括：
+
+- 输入电容`CISS`约为1988pF；
+- 总栅极电荷`Qg`约为35nC（特定测试条件下）；
+- 米勒电荷`Qgd`约为8.8nC。
+
+PMOS关断时，`RUP`负责给栅极充电。可以先用RC时间常数粗略估算：
+
+```text
+τ ≈ RUP × CISS
+```
+
+例如：
+
+| RUP | 估算时间常数τ |
+|---:|---:|
+| 1.2kΩ | 约2.4μs |
+| 2.2kΩ | 约4.4μs |
+| 2.4kΩ | 约4.8μs |
+| 3.6kΩ | 约7.2μs |
+
+实际关断时间还受到栅极电荷、米勒平台、漏极电压变化和PCB寄生参数影响，不能只用一个RC公式定论。
+
+### 10.1 RUP太大
+
+可能产生：
+
+- PMOS关断变慢；
+- 换向时上管尚未完全关断，下管已经开启；
+- H桥上下管短暂直通；
+- 电源出现大电流尖峰；
+- MOS管异常发热；
+- 电路发出异响；
+- 严重时损坏MOS管或电源。
+
+### 10.2 RUP太小
+
+可能产生：
+
+- PMOS关断速度加快；
+- 但下拉时大量电流被RUP分走；
+- 栅极下拉不够，PMOS的负`VGS`不足；
+- PMOS没有充分导通，导通电阻增大；
+- 驱动回路静态功耗增加；
+- 电阻和驱动管温升增加。
+
+所以“上拉电阻越小越安全”并不成立。
+
+---
+
+## 11. 电阻功耗不能只按照死区时间计算
+
+这是非常容易出现的误区。
+
+死区时间，例如25μs或50μs，表示换向时两边都关闭的保护时间。它不代表上拉、下拉电阻只通电25μs或50μs。
+
+当PMOS保持导通时：
+
+- `QDRV`持续导通；
+- `RUP`、`RDOWN`和稳压管可能持续有电流；
+- 电阻功耗会持续整个PMOS导通阶段。
+
+因此必须分别检查：
+
+1. 正常导通期间的连续或平均功耗；
+2. 换向尖峰期间的瞬时脉冲功耗。
+
+### 11.1 对比算例：24V钳位在12V、RUP=1.2kΩ、RDOWN=1kΩ
+
+钳位时：
+
+```text
+PUP   = 12² / 1.2k ≈ 120mW
+PDOWN = 12² / 1k   ≈ 144mW
+PZ    = 12V × 2mA ≈ 24mW
+```
+
+普通0603电阻常见连续额定功率约为0.1W，但不同厂家、环境温度和PCB焊盘条件会有差异。
+
+因此：
+
+- 120mW和144mW不能简单地当成“只有50μs”；
+- 如果PMOS长时间保持导通，电阻可能接近连续承受该功耗；
+- 建议使用0805封装，或使用多个电阻分担功耗；
+- 最终必须查看所选电阻的数据手册和降额曲线。
+
+图1当前采用2.4kΩ上拉和3kΩ下拉，24V稳定工作时功耗分别约为47mW和59mW，不会出现上述持续钳位功耗；但0603电阻仍应考虑环境温度和功率降额。
+
+---
+
+## 12. 取消稳压管时如何选择电阻
+
+如果决定不安装稳压管，就必须完全依靠电阻分压限制`VGS`。
+
+设计时应检查最坏情况：
+
+```text
+|VGS|max = VCC,max × RUP,max / (RUP,max + RDOWN,min)
+```
+
+必须同时考虑：
+
+- 电源最高电压；
+- 电源启动和负载突卸尖峰；
+- 电阻误差；
+- 温度；
+- 驱动管导通压降；
+- PCB寄生参数。
+
+### 12.1 同时兼容12V和24V的参考值
+
+可以考虑：
+
+```text
+RUP   = 2.4kΩ
+RDOWN = 3kΩ
+```
+
+计算结果：
+
+| 输入电压 | 栅源电压VGS | 回路电流 |
+|---:|---:|---:|
+| 12V | 约-5.33V | 约2.22mA |
+| 24V | 约-10.67V | 约4.44mA |
+
+24V时电阻功耗：
+
+```text
+PUP   ≈ 47mW
+PDOWN ≈ 59mW
+```
+
+这个组合具有以下特点：
+
+- 12V输入时仍能获得约-5.33V驱动；
+- 24V输入时约为-10.67V；
+- 正常功耗低于1.2kΩ加1kΩ方案；
+- 2.4kΩ上拉的关断速度仍然较快；
+- 不需要依靠稳压管在正常工作时持续击穿。
+
+即使使用这个分压，保留稳压管仍然有价值：它在正常工作时不导通，只在异常尖峰时保护PMOS。
+
+---
+
+## 13. 两种方案对比
+
+### 方案A：电阻分压加稳压管
+
+优点：
+
+- 对栅源尖峰有额外保护；
+- 元件误差或异常状态下更安全；
+- 可以限制`VGS`不超过约12V。
+
+缺点：
+
+- 必须保证稳压管具有合适的工作电流；
+- 如果设计成稳压管持续击穿，会增加静态功耗；
+- 电阻功耗和稳压管功耗都需要核算。
+
+适合：
+
+- 24V供电；
+- H桥换向尖峰明显；
+- 对可靠性要求较高；
+- PCB空间允许增加保护器件。
+
+### 方案B：只使用电阻分压
+
+优点：
+
+- 元件少；
+- 不存在稳压管持续工作产生的额外功耗；
+- 参数计算直观。
+
+缺点：
+
+- 失去栅源尖峰钳位；
+- 对电源波动、电阻误差和PCB寄生参数更敏感；
+- 上拉电阻开路等故障可能让`VGS`超过额定值。
+
+适合：
+
+- 输入电压范围明确；
+- 电源尖峰受到良好控制；
+- 已经通过示波器确认`VGS`安全；
+- 有足够的设计余量。
+
+---
+
+## 14. 本电路的建议
+
+### 14.1 如果保留12V稳压管
+
+建议：
+
+- 不要只根据“关断越快越好”无限减小上拉电阻；
+- 计算稳压管电流，确认能够形成有效钳位；
+- 按整个PMOS导通时间核算电阻平均功耗；
+- 对超过或接近0.1W的电阻优先使用0805；
+- 用示波器测量真实`VGS`，确认导通时约为-10V至-12V，关断时回到0V。
+
+### 14.2 如果取消稳压管
+
+12V至24V输入可以先测试：
+
+```text
+RUP   = 2.4kΩ
+RDOWN = 3kΩ
+```
+
+但必须满足：
+
+- 实测最大负`VGS`有足够余量；
+- 实测正向和反向尖峰没有接近`±20V`；
+- 电源母线已经做好TVS和就近电容；
+- PMOS能在下管开启前完全关断；
+- 保留足够的硬件或软件死区。
+
+### 14.3 关于死区
+
+死区的最终取值不能仅凭计算，应根据示波器实测决定。
+
+至少同时测量：
+
+- 上管PMOS的`VGS`；
+- 下管NMOS的`VGS`；
+- H桥输出节点；
+- 24V母线电压；
+- 条件允许时测量桥臂电流。
+
+判断标准是：
+
+> 下管开始导通之前，对应上管必须已经退出导通区，并且换向过程中没有异常母线电流尖峰。
+
+---
+
+## 15. 初学者常见误区
+
+### 误区一：PMOS的20V是开启阈值
+
+错误。20V通常是栅源极最大耐压。真正的`VGS(th)`一般只有约1V至3V，但这个电压只能让MOS管刚刚开始导通。
+
+### 误区二：栅极下拉后一定是0V
+
+错误。如果存在上拉和下拉电阻，栅极由两个电阻分压，不会自然等于0V。
+
+### 误区三：装了12V稳压管，VGS就一定是-12V
+
+错误。稳压管必须获得足够的反向电流，实际钳位电压还受到电流、温度和器件误差影响。
+
+### 误区四：上拉电阻越小，电路越安全
+
+错误。上拉电阻减小会加快关断，但也会降低PMOS导通时的负`VGS`，并增加静态功耗。
+
+### 误区五：电阻的高功耗只持续死区时间
+
+错误。PMOS导通期间，分压回路可能持续有电流。必须按照实际占空比和最坏工作状态核算平均功耗。
+
+### 误区六：栅源稳压管可以保护整个MOS管
+
+错误。它主要保护`VGS`，不能代替24V母线TVS，也不能阻止`VDS`超过MOS管额定值。
+
+---
+
+## 16. 最终检查清单
+
+原理图确定后，至少完成以下检查：
+
+- [ ] 确认PMOS的`VGS(th)`、推荐驱动电压和`VGS(max)`；
+- [ ] 计算12V和24V下的正常`VGS`；
+- [ ] 计算最高电源电压和电阻误差下的最坏`VGS`；
+- [ ] 计算上拉、下拉电阻连续功耗；
+- [ ] 计算稳压管正常电流和功耗；
+- [ ] 检查0603/0805电阻的额定功率和降额曲线；
+- [ ] 测量PMOS栅极对源极波形，而不是只测栅极对地；
+- [ ] 检查换向时是否有正向或反向`VGS`尖峰；
+- [ ] 检查上下管是否发生交叉导通；
+- [ ] 验证`PWM_C=1、PWM_W=1`在软硬件中都不会出现；
+- [ ] 验证每次方向切换都经过`00`关闭状态；
+- [ ] 检查24V母线是否超过PMOS的`VDS`额定值；
+- [ ] 高温、低温、最低输入和最高输入条件下重复测试。
+
+---
+
+## 17. 总结
+
+PMOS栅极驱动电阻的选择，本质上是在以下四项之间寻找平衡：
+
+1. PMOS必须得到足够的负`VGS`，保证充分导通；
+2. PMOS必须快速回到`VGS≈0V`，保证及时关断；
+3. 分压回路的电流和电阻功耗不能过大；
+4. 栅源电压和换向尖峰不能超过MOS管额定值。
+
+稳压管的核心作用是保护PMOS栅源极，而不是替代电阻分压，也不是控制死区。合理的设计应先用电阻比例确定正常工作点，再用稳压管处理异常和瞬态过压，最后通过示波器实测确认。
+
+对于这套12～24V、2P2N主桥加2只驱动MOS的双色LED电路，还必须始终遵守两个基本原则：
+
+1. `PWM_C`和`PWM_W`不能同时为高电平；
+2. 两个电流方向切换时，必须先输出`00`，等待确认安全的死区后再开启另一方向。

Document/DWM22_黑盒用户测试文档.md

@@ -0,0 +1,203 @@
+# DWM22 黑盒用户测试文档
+
+## 1. 文档信息
+
+| 项目 | 内容 |
+| --- | --- |
+| 产品名称 | DWM22 |
+| 测试类型 | 用户黑盒功能测试 |
+| 固件校验码 | `0F9DA5A0` |
+| 固件提交 | `ee68f37 DWM22量产测试` |
+| APP | Ultra Life |
+| 测试日期 |  |
+| 测试人员 |  |
+| 样机编号 |  |
+
+> 测试人员只根据实际操作和灯光表现判断结果，不需要查看程序、波形或内部数据。
+
+## 2. 测试准备
+
+- DWM22 测试样机 1 台。
+- 双色 LED 灯板及 12～24V 配套电源。
+- 安装最新版 Ultra Life APP 的手机 1 台。
+- 433 遥控器至少 2 个；测试 5 路记忆时准备 6 个。
+- 遥控距离测试场地：无遮挡、直线距离大于 12 米。
+- 每个用例测试完成后，在“结果”栏填写：通过或失败。
+
+## 3. 产品模式说明
+
+DWM22 共 14 个产品模式，固定顺序如下：
+
+**暖光静态 → 冷光静态 → 中性光静态 → 暖光呼吸 → 冷光呼吸 → 中性光呼吸 → 三色呼吸 → 暖冷连续渐变 → 暖冷中性渐变 → 暖光闪烁 → 冷光闪烁 → 中性光闪烁 → 暖冷中性跳变 → 三色闪烁**
+
+- 模式 1～3 为静态模式，可以调节亮度。
+- 模式 4～14 为动态模式，可以调节亮度和速度。
+- 遥控器“模式＋”按上述顺序向后切换，“模式－”按相反顺序返回。
+- 到达模式 14 后继续按“模式＋”，应停留在模式 14，不从头循环。
+- 到达模式 1 后继续按“模式－”，应停留在模式 1，不跳到模式 14。
+- APP 色温环属于自定义静态色温，不占用以上 14 个模式编号。
+
+| 顺序 | 模式名称 | 产品效果说明 |
+| --- | --- | --- |
+| 1 | 暖光静态 | 仅暖光常亮 |
+| 2 | 冷光静态 | 仅冷光常亮 |
+| 3 | 中性光静态 | 暖光和冷光混合形成中性光 |
+| 4 | 暖光呼吸 | 暖光由暗到亮、再由亮到暗循环 |
+| 5 | 冷光呼吸 | 冷光由暗到亮、再由亮到暗循环 |
+| 6 | 中性光呼吸 | 暖冷两路保持中性比例同步呼吸 |
+| 7 | 三色呼吸 | 暖光、冷光、中性光依次完成呼吸 |
+| 8 | 暖冷连续渐变 | 暖光与冷光互补变化，一个降低时另一个升高，全程不断光 |
+| 9 | 暖冷中性渐变 | 在暖光、冷光和中性光之间平滑渐变，颜色衔接时保持亮光 |
+| 10 | 暖光闪烁 | 暖光按设定速度亮灭 |
+| 11 | 冷光闪烁 | 冷光按设定速度亮灭 |
+| 12 | 中性光闪烁 | 中性光按设定速度亮灭 |
+| 13 | 暖冷中性跳变 | 暖光、冷光、中性光直接切换，不做渐变 |
+| 14 | 三色闪烁 | 暖光、冷光、中性光依次闪烁，中间包含熄灭节拍 |
+
+## 4. 基本功能
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 01 | 接通电源 | 灯具能在正常时间内点亮；无长时间不亮、异常闪烁、异响或发热 |  |  |
+| 02 | 使用遥控器或 APP 开灯、关灯 | 开关响应正确，开关过程柔和；关灯后两路 LED 均完全熄灭 |  |  |
+| 03 | 连续开关灯 10 次 | 每次均正常响应，无死机、失控或蓝牙广播消失 |  |  |
+| 04 | 在暖光、冷光、中性光之间反复切换 | 颜色正确，过渡柔和，无突然增亮、突然变暗或异常颜色闪现 |  |  |
+| 05 | 从最低亮度逐级调到最高亮度，再调回最低亮度 | 亮度变化连续、均匀，无明显顿挫、抖动或提前熄灭 |  |  |
+| 06 | 中性光在低亮度下持续观察 30 秒 | 无肉眼可见抖动，两路混色比例稳定 |  |  |
+
+## 5. 遥控器对码
+
+对码操作：连接 DWM22，在 APP“更多”页面点击“遥控器对码”，在 5 秒倒计时内长按遥控器“亮度＋”按键。
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 07 | 使用未对码遥控器直接控制灯具 | 灯具不响应 |  |  |
+| 08 | 在 APP 中进入“遥控器对码”，长按遥控器“亮度＋” | 灯具给出对码闪烁反馈；APP 显示“对码成功”和已对码数量 |  |  |
+| 09 | 对码成功后测试遥控器开关、模式和亮度按键 | 所有按键均能正常控制灯具，短按一次即可响应 |  |  |
+| 10 | 打开对码页面但不操作遥控器，等待 5 秒 | 对码自动结束，APP 提示未收到有效信号；原有遥控器不受影响 |  |  |
+| 11 | 将已经对码的同一个遥控器再次对码 | 可以提示对码成功，但已对码数量不增加，不重复占用位置 |  |  |
+| 12 | 依次对码 5 个不同遥控器 | 5 个遥控器都能控制灯具，APP 显示 `5/5` |  |  |
+| 13 | 已有 5 个遥控器后，再对码第 6 个遥控器 | 第 6 个遥控器可以使用；最早对码的遥控器被替换，其余最近 4 个仍可使用 |  |  |
+| 14 | 对码成功后切断电源，重新上电 | 已对码遥控器仍能使用，对码数据不会因断电丢失 |  |  |
+
+## 6. 遥控器清码
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 15 | APP“更多”页面点击“清除遥控器” | 出现二次确认窗口，不会直接清码 |  |  |
+| 16 | 在确认窗口点击“取消” | 遥控器数据保留，原遥控器仍可使用 |  |  |
+| 17 | 再次进入清码并点击“清除” | 灯具给出清码反馈，APP 提示“清码成功”，已对码数量变为 0 |  |  |
+| 18 | 清码后测试全部旧遥控器 | 所有旧遥控器均不能控制灯具 |  |  |
+| 19 | 清码后重新对码一个遥控器 | 可以正常重新对码并控制灯具 |  |  |
+| 20 | 清码后断电重启，再测试旧遥控器 | 清码结果被记忆，旧遥控器仍不能控制灯具 |  |  |
+
+## 7. 遥控距离
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 21 | 在无遮挡环境下，将遥控器与灯具距离拉到 12 米以上 | 在大于 12 米的位置仍可正常控制，判定距离合格 |  | 实测距离：____m |
+| 22 | 在 12 米位置，分别短按开关、模式＋、模式－、亮度＋、亮度－各 10 次 | 按键能可靠响应，不能依赖连续按两次或刻意延长短按时间；建议每个按键至少 9 次一次响应 |  |  |
+| 23 | 改变遥控器朝向，在 12 米位置重复测试 | 不应频繁失控；正常手持方向下可以稳定操作 |  |  |
+
+## 8. 模式顺序测试
+
+先在 APP 中选择模式 1，然后使用遥控器“模式＋”按顺序测试到模式 14，每个模式至少观察 20 秒。之后使用“模式－”从模式 14 反向测试回模式 1。
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| M01 | APP 依次点击模式 1～14 | 实际效果与 APP 模式名称一致，顺序正确 |  |  |
+| M02 | 从模式 1 开始，遥控短按“模式＋”13次 | 严格按照 1→2→…→14 切换，每次只前进一个模式 |  |  |
+| M03 | 在模式 14 再按“模式＋” | 保持模式 14，不循环回模式 1 |  |  |
+| M04 | 从模式 14 开始，遥控短按“模式－”13次 | 严格按照 14→13→…→1 返回，每次只后退一个模式 |  |  |
+| M05 | 在模式 1 再按“模式－” | 保持模式 1，不跳转到模式 14 |  |  |
+| M06 | 对比 APP 选中模式、灯光效果和遥控切换结果 | 三者始终对应，不出现错位一个模式的情况 |  |  |
+
+| 模式 | 效果 | 主要检查内容 | 结果 |
+| --- | --- | --- | --- |
+| 1 | 暖光静态 | 暖光正确，亮度稳定 |  |
+| 2 | 冷光静态 | 冷光正确，亮度稳定 |  |
+| 3 | 中性光静态 | 两路混色正确，无抖动 |  |
+| 4 | 暖光呼吸 | 从低到高、再从高到低，过程柔和 |  |
+| 5 | 冷光呼吸 | 从低到高、再从高到低，过程柔和 |  |
+| 6 | 中性光呼吸 | 呼吸时间与单色接近，低亮度无明显抖动，峰值亮度正常 |  |
+| 7 | 三色呼吸 | 暖、冷、中性依次呼吸；上一颜色降到最低后下一颜色平滑升起 |  |
+| 8 | 暖冷连续渐变 | 暖光降低时冷光同步升高，全程不断光、无突然跳变 |  |
+| 9 | 暖冷中性渐变 | 暖、冷、中性过渡自然；颜色交接时不突然变黑或异常增亮 |  |
+| 10 | 暖光闪烁 | 只出现暖光，节奏稳定 |  |
+| 11 | 冷光闪烁 | 只出现冷光，节奏稳定 |  |
+| 12 | 中性光闪烁 | 只出现中性光，两路比例稳定 |  |
+| 13 | 暖冷中性跳变 | 暖、冷、中性直接切换，颜色正确，无多余低亮度闪光 |  |
+| 14 | 三色闪烁 | 暖、冷、中性按设计闪烁，无错误颜色 |  |
+
+补充检查：
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 24 | 在模式 1～3 之间切换 | 使用柔和过渡，不出现最后突然亮一下的现象 |  |  |
+| 25 | 从静态模式切换到模式 4～7 | 呼吸从低亮度开始，不会直接从最高亮度开始 |  |  |
+| 26 | 切换到模式 10～14 | 直接进入正确动态效果，不出现其他颜色或多余低亮度脉冲 |  |  |
+| 27 | 在动态模式下调节亮度 | 动态效果整体亮度可以调节，变化正确 |  |  |
+| 28 | 在动态模式下调节速度 1～10 | 速度变化明显且方向正确；APP 显示值与实际效果一致 |  |  |
+| 29 | 遥控器长按模式＋或模式－ | 按下时先执行一次，持续按住时约每 500ms 切换一次，不快速乱跳 |  |  |
+
+## 9. 掉电记忆
+
+### 9.1 全部带记忆
+
+在 APP“更多 → 断电设置”中选择“全部带记忆”。
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 30 | 设置任意静态颜色、亮度，等待 2 秒后断电重启 | 恢复断电前的颜色和亮度 |  |  |
+| 31 | 设置任意动态模式、亮度和速度，等待 2 秒后断电重启 | 恢复断电前的模式、亮度和速度 |  |  |
+| 32 | 关灯后等待 2 秒，再切断电源并重新上电 | 恢复关灯状态，不应自行亮起 |  |  |
+| 33 | 在中性光状态下改变亮度、模式或断电设置 | 保存过程中灯光不闪烁、不熄灭，蓝牙连接不中断 |  |  |
+
+### 9.2 断电切换功能
+
+在 APP“更多 → 断电设置”中选择“断电切换功能”。
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 34 | 设置一个容易识别的亮度，连续断电上电 4 次 | 每次上电依次为：暖光 → 冷光 → 中性光 → 暖光 |  |  |
+| 35 | 检查每次上电后的亮度 | 三种静态颜色均保留之前设置的亮度 |  |  |
+| 36 | 在任意动态模式或自定义色温下断电，再上电 | 仍按暖光、冷光、中性光的固定顺序轮换，不受断电前模式影响 |  |  |
+| 37 | 选择断电切换功能后断电重启多次 | 该设置本身被记忆，不会自动恢复为“全部带记忆” |  |  |
+| 38 | 在 APP 中来回切换两种断电设置 | 切换时灯光不闪烁、不突变，蓝牙连接保持正常 |  |  |
+
+## 10. 蓝牙控制
+
+| 编号 | 测试操作 | 预期结果 | 结果 | 备注 |
+| --- | --- | --- | --- | --- |
+| 39 | 打开 APP 搜索设备 | 能发现名称为 `DWM22` 的设备 |  |  |
+| 40 | 连接 DWM22 | 可以正常进入 DWM22 控制界面，连接稳定 |  |  |
+| 41 | APP 控制开灯和关灯 | 灯具正确响应，APP 状态与灯具一致 |  |  |
+| 42 | APP 将亮度从 1 调到 100，再调回 1 | 灯光变化平滑，最低亮度可正常显示，无明显抖动或顿挫 |  |  |
+| 43 | APP 拖动色温环，从暖光连续调到冷光并往返 | 色温连续变化，采用柔和过渡，无黑场、突变或错误颜色 |  |  |
+| 44 | APP 依次选择 14 个模式 | 灯具效果与 APP 名称、图标和选中状态一致 |  |  |
+| 45 | APP 调节动态亮度和速度 1～10 | 实际亮度和速度正确变化，界面数值正确 |  |  |
+| 46 | 使用遥控器改变开关、模式、亮度或速度 | APP 已显示的设备状态能同步更新，不出现明显错乱 |  |  |
+| 47 | 设置 APP 定时关机 | 到达设定时间后灯具自动关闭 |  |  |
+| 48 | 蓝牙连接中关闭手机蓝牙或让设备断电 | APP 自动退出设备控制页，不停留在失效界面 |  |  |
+| 49 | 恢复设备电源和手机蓝牙后重新连接 | 可以再次发现并连接，所有控制恢复正常 |  |  |
+| 50 | 蓝牙连接状态下连续操作 5 分钟 | 无断链、无卡死、无控制延迟持续增大，灯光无异常抖动 |  |  |
+
+## 11. 测试结论
+
+| 项目 | 结论 |
+| --- | --- |
+| 对码功能 | □ 通过　□ 失败 |
+| 清码功能 | □ 通过　□ 失败 |
+| 遥控距离大于 12m | □ 通过　□ 失败 |
+| 掉电记忆 | □ 通过　□ 失败 |
+| 模式与灯光效果 | □ 通过　□ 失败 |
+| 蓝牙控制 | □ 通过　□ 失败 |
+| 整机测试结论 | □ 合格　□ 不合格 |
+
+问题记录：
+
+1.  
+2.  
+3.  
+
+测试人员签名：________________　　日期：________________

component/xc6xx_drivers/Drivers/xc_driver/xc_drv_fmc_spi.c

@@ -340,6 +340,10 @@ __RAM_CODE static uint8_t xc_fmc_spi_flash_status(void)
     return sta[1];
 }
 
+__RAM_CODE __WEAK void xc_fmc_spi_flash_busy_hook(void)
+{
+}
+
 /**
  ****************************************************************************************
  * @brief		xc_fmc_spi_flash_wait_busy
@@ -354,8 +358,14 @@ __RAM_CODE static uint8_t xc_fmc_spi_flash_status(void)
  */
 __RAM_CODE static void xc_fmc_spi_flash_wait_busy(void)
 {
-    while ((xc_fmc_spi_flash_status() & PUYA_FLASH_STATUS_WIP_SET))
-        ;
+    for (;;) {
+        xc_fmc_spi_flash_busy_hook();
+        if ((xc_fmc_spi_flash_status() &
+             PUYA_FLASH_STATUS_WIP_SET) == 0U)
+            break;
+    }
+
+    xc_fmc_spi_flash_busy_hook();
 }
 
 /**
@@ -472,6 +482,30 @@ __RAM_CODE void xc_fmc_spi_flash_erase_page(uint32_t addr)
  * @retval      void 
  ****************************************************************************************
  */
+__RAM_CODE void xc_fmc_spi_flash_write_16bytes(uint32_t addr, uint8_t *data)
+{
+    uint8_t cmd[16 + 4] = {0};
+
+    xc_fmc_spi_flash_wait_busy();
+    xc_fmc_spi_flash_write_enable();
+    xc_fmc_spi_flash_wait_busy();
+
+    cmd[0] = CMD_PAGE_PROGRAM;
+    cmd[1] = addr >> 16;
+    cmd[2] = addr >> 8;
+    cmd[3] = addr;
+
+    ram_memcpy_bytes(&cmd[4], data, 16);
+
+    xc_fmc_status_wait_idle();
+
+    xc_fmc_spi_enable(FMC_SSI_CTRL0_DFS_LEN_32BIT);
+    xc_fmc_spi_write_nbyte(cmd, sizeof(cmd));
+
+    xc_fmc_spi_flash_wait_busy();
+    xc_fmc_spi_disable();
+}
+
 __RAM_CODE void xc_fmc_spi_flash_write_page(uint32_t addr, uint8_t *data,
                                          uint16_t size)
 {

component/xc6xx_drivers/Drivers/xc_driver/xc_drv_fmc_spi.h

@@ -293,6 +293,7 @@ void xc_fmc_spi_flash_wait_busy(void);
 void xc_fmc_spi_flash_write_enable(void);
 void xc_fmc_spi_flash_erase_sector(uint32_t addr);
 void xc_fmc_spi_flash_erase_page(uint32_t addr);
+void xc_fmc_spi_flash_write_16bytes(uint32_t addr, uint8_t *data);
 void xc_fmc_spi_flash_write_page(uint32_t addr, uint8_t *buff,
                                             uint16_t size);
 void xc_fmc_spi_flash_read_page(uint32_t addr, uint8_t *buff,

component/xc6xx_drivers/Drivers/xc_driver/xc_drv_timer.c

@@ -171,7 +171,7 @@ void xc_timer_stop(uint8_t reg_idx)
     timer_tcr__tes__setf(reg_idx, TIMER_TCR_TES_DISABLE);
 }
 
-void TIMER0_Handler(void)
+__RAM_CODE void TIMER0_Handler(void)
 {
     (void)timer_tic_get(TIMER0_IDX);
     if (timer_n_callback[0] != NULL)
@@ -192,7 +192,7 @@ void TIMER2_Handler(void)
         timer_n_callback[2](NULL);
 }
 
-void TIMER3_Handler(void)
+__RAM_CODE void TIMER3_Handler(void)
 {
     (void)timer_tic_get(TIMER3_IDX);
     if (timer_n_callback[3] != NULL)

make_release_bin.bat

@@ -0,0 +1,5 @@
+@echo off
+setlocal
+cd /d "%~dp0"
+powershell -ExecutionPolicy Bypass -File "%~dp0tools\make_release_bin.ps1" %*
+exit /b %errorlevel%

project/example/ble/ble_peripheral/app/api/app_task.h

@@ -397,7 +397,7 @@
 	
 	
 /// Default Device Name
-#define APP_DFLT_DEVICE_NAME     ("PWM32EPRO") //
+#define APP_DFLT_DEVICE_NAME     ("DWM22") //
 #define APP_DFLT_DEVICE_NAME_LEN (sizeof(APP_DFLT_DEVICE_NAME))
 #define APP_DFLT_DEVICE_NAME_LEN1 (sizeof(APP_DFLT_DEVICE_NAME1))
 #define APP_DFLT_DEVICE_NAME2     ("Second_test")

project/example/ble/ble_peripheral/app/src/Mode.c

@@ -7,9 +7,11 @@
 #include "timeslice.h"
 #include "RF433.h"
 #include "usr_server.h"
+#include "light_transition.h"
 
 
 uint16_t time_1[11]={8,10,12,14,16,18,20,22,24,26,26}; 
+static const uint16_t time_1_neutral[11]={12,15,18,21,24,27,30,33,35,38,38};
 uint16_t time_2[11]={100,200,300,400,500,600,700,800,900,1000,1000}; 
 uint16_t time_3[11]={200, 350, 450, 550, 650, 750, 850, 950, 1200,1500,1500}; 
 
@@ -20,17 +22,18 @@ uint8_t direction = 1; //
 
 uint8_t choose_mode_falsg=0;  //模式值
 uint8_t choose_mode_bh=0;   //模式变化
+static uint8_t mode_entry_initialized;
 
 uint16_t Color_table_static[3][2]={
-		{10,0},   //暖光
-		{4,4},   //中性光
-		{0,10},   //冷光
+        {100,0},   // warm light
+        {50,50},   // neutral light
+        {0,100},   // cool light
 };
 
 
 uint16_t Color_table[3][2]={ //动态时候的数组
 		{100,0},   //暖光
-		{40,40},   //中性光
+		{50,50},   //中性光
 		{0,100},   //冷光
 };
 
@@ -46,15 +49,15 @@ void Set_timing(){
 			}
 }
 void Start_PWM(){
+	  Light_Transition_RequestOn();
 	  deviceStatus=POWERON;
 	  startTimer(&timer1,1);
 }
 
 
 void Stop_PWM(){
-	  deviceStatus=POWEROFF;
-		xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET); 
-		xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET); 
+    Light_Transition_RequestOff();
+    deviceStatus=POWEROFF;
 }
 
 
@@ -62,96 +65,110 @@ void set_mode(){
 	if(choose_mode_bh==0){
 		choose_mode_bh=1;
 		switch(choose_mode_falsg){
-		//
 			case 0:
-				//暖光
-				  W_PWM=Color_table_static[0][0];
-			    C_PWM=Color_table_static[0][1];
-					driveMode=1;//切换为暖光的底层输出
-				  Mode=mode0;
+				W_PWM=100U; C_PWM=0U; driveMode=1U; Mode=mode0;
 				break;
 			case 1:
-				 //冷光
-				 W_PWM=Color_table_static[2][0];
-			   C_PWM=Color_table_static[2][1];
-			   driveMode=2;//切换为冷光的底层输出
-				 Mode=mode0;
+				W_PWM=0U; C_PWM=100U; driveMode=2U; Mode=mode0;
 				break;
 			case 2:
-				//中性光
-				 W_PWM=Color_table_static[1][0];
-			   C_PWM=Color_table_static[1][1];
-			   driveMode=0;//切换为中性光的底层输出
-				 Mode=mode0;
+				W_PWM=50U; C_PWM=50U; driveMode=0U; Mode=mode0;
 				break;
 			case 3:
-				//暖光呼吸		
-				 W_PWM=Color_table[0][0];
-			   C_PWM=Color_table[0][1];
-				 driveMode=1;//切换为暖光的底层输出
-				 direction=1;//呼吸方向恢复默认值
-				 Mode=mode1;
+				W_PWM=1U; C_PWM=0U; driveMode=1U; direction=0U; Mode=mode1;
 				break;
-			 case 4:
-				//冷光呼吸
-				 W_PWM=Color_table[2][0];
-			   C_PWM=Color_table[2][1];
-			   driveMode=2;//切换为中性光的底层输出
-			   direction=1;//呼吸方向恢复默认值
-				 Mode=mode1;
+			case 4:
+				W_PWM=0U; C_PWM=1U; driveMode=2U; direction=0U; Mode=mode1;
 				break;
-			 case 5:
-					//三个色温轮询呼吸//先从暖光开始呼吸
-					 W_PWM=Color_table[0][0];
-					 C_PWM=Color_table[0][1];
-					 driveMode=1;//切换为暖光的底层输出
-					 direction=1;//呼吸方向恢复默认值
-			 		
-					 Mode=mode1;
+			case 5:
+				W_PWM=1U; C_PWM=1U; driveMode=0U; direction=0U; Mode=mode1;
 				break;
-			 case 6:
-				//暖光跳变
-			   W_PWM=Color_table[0][0];
-			   C_PWM=Color_table[0][1];
-				 driveMode=1;//切换为暖光的底层输出
-				 direction=1;//呼吸方向恢复默认值
-				 Mode=mode2;
+			case 6:
+				W_PWM=1U; C_PWM=0U; driveMode=1U; direction=0U; Mode=mode1;
 				break;
-				 case 7:
-				//中性光跳变
-				 W_PWM=Color_table[1][0];
-			   C_PWM=Color_table[1][1];
-			   driveMode=0;//切换为中性光的底层输出
-				 Mode=mode2;
+			case 7:
+				W_PWM=100U; C_PWM=0U; driveMode=1U; direction=1U; Mode=mode3;
 				break;
-			 case 8:
-				//冷光跳变
-			   W_PWM=Color_table[2][0];
-			   C_PWM=Color_table[2][1];
-			   driveMode=2;//切换为中性光的底层输出
-			   direction=1;//呼吸方向恢复默认值
-				 Mode=mode2;
+			case 8:
+				W_PWM=100U; C_PWM=0U; driveMode=1U; direction=0U; Mode=mode3;
 				break;
-			 case 9:
-				//暖光中性光冷交替跳变，先从暖光跳变
-			   W_PWM=Color_table[0][0];
-			   C_PWM=Color_table[0][1];
-				 driveMode=1;//切换为暖光的底层输出
-				 direction=1;//呼吸方向恢复默认值
-				 Mode=mode2;
+			case 9:
+				W_PWM=100U; C_PWM=0U; driveMode=1U; direction=1U; Mode=mode2;
 				break;
-			 
-			  case 10://圆环模式
-				 Mode=mode0;
+			case 10:
+				W_PWM=0U; C_PWM=100U; driveMode=2U; direction=1U; Mode=mode2;
+				break;
+			case 11:
+				W_PWM=50U; C_PWM=50U; driveMode=0U; direction=1U; Mode=mode2;
+				break;
+			case 12:
+				W_PWM=100U; C_PWM=0U; driveMode=1U; direction=2U; Mode=mode2;
+				break;
+			case 13:
+				W_PWM=100U; C_PWM=0U; driveMode=1U; direction=2U; Mode=mode2;
+				break;
+			case CUSTOM_TEMPERATURE_MODE:
+				Mode=mode0;
+				break;
+			default:
+				choose_mode_falsg=0U;
+				W_PWM=100U; C_PWM=0U; driveMode=1U; Mode=mode0;
 				break;
 		}
+		if(mode_entry_initialized)
+		{
+			if(choose_mode_falsg <= 2U)
+			{
+				Light_Transition_BeginModeChange();
+			}
+			else if(choose_mode_falsg == CUSTOM_TEMPERATURE_MODE)
+			{
+				/*
+				 * APP CCT packets can arrive continuously while the color
+				 * ring is dragged. Restart the same 200 ms linear transition
+				 * used by static mode changes from the current visible
+				 * output, so the latest W/C target is followed without a
+				 * discontinuity.
+				 */
+				Light_Transition_BeginModeChange();
+			}
+			else
+			{
+				Light_Transition_ModeActive=0U;
+				Light_Transition_SyncBrightness(Brightness);
+			}
+			if(Mode==mode1){
+				if(choose_mode_falsg==5U)
+					startTimer(&timer1,time_1_neutral[Speed]);
+				else
+					startTimer(&timer1,time_1[Speed]);
+			}else if(Mode==mode2){
+				startTimer(&timer1,time_2[Speed]);
+			}else if(Mode==mode3){
+				startTimer(&timer1,time_1[Speed]);
+			}else{
+				startTimer(&timer1,1U);
+			}
+		}
+		else
+		{
+			mode_entry_initialized=1;
+		}
 	}
+	Light_Transition_Task();
 }
 void Mode0(){ //常量
-  UpdateDisplay();
+  (void)0;/* transition */
 }
 
 
+#define THREE_COLOR_WAIT_NEUTRAL 6U
+#define THREE_COLOR_WAIT_COLD    7U
+#define THREE_COLOR_WAIT_WARM    8U
+#define OVERLAP_GRADIENT_LEVEL   40U
+#define OVERLAP_NEUTRAL_LOW      20U
+#define OVERLAP_NEUTRAL_PEAK     50U
+
 static uint8_t breathespeed_flag=0; //该变量只是用来处理三种颜色呼吸时候，对中性光的速度变大
 static void breathe_fun(uint16_t *PWM_1, uint16_t *PWM_2, uint8_t flag) {
     if (flag == 0) {
@@ -190,84 +207,85 @@ static void breathe_fun(uint16_t *PWM_1, uint16_t *PWM_2, uint8_t flag) {
 //        }
     }
 }
-void Mode1(){ //呼吸
-	if(choose_mode_falsg==3){ //暖光呼吸
-	  	breathe_fun(&C_PWM,&W_PWM,0);
-	}else if(choose_mode_falsg==4){//冷光呼吸
-		  breathe_fun(&W_PWM,&C_PWM,0);
-	}else if(choose_mode_falsg==5){	
-		 switch (direction) {
-				case 0:
-					 breathespeed_flag=0;
-						W_PWM += 1;
-						C_PWM = 0;
-
-						if (W_PWM >= 100) {
-								direction = 1;
-						}
-						
-						break;
-				case 1:
-					  breathespeed_flag=0;
-						W_PWM -= 1;
-						C_PWM = 0;
-						if (W_PWM <= 1) {
-								direction = 2;
-								driveMode=0;
-								W_PWM = 1;
-								C_PWM = 0;
-						}
-						break;
-				case 2:
-					  breathespeed_flag=1;
-						W_PWM += 1;
-						C_PWM += 1;
-						if (W_PWM >= 40) {
-								W_PWM=40;
-								C_PWM=40;
-								direction = 3;
-						}
-						break;
-				case 3:
-					breathespeed_flag=1;
-						W_PWM -= 1;
-						C_PWM -= 1;
-						if (W_PWM <=1) {
-								driveMode=2;
-								direction = 4;
-								W_PWM = 1;
-								C_PWM = 1;
-						}
-						break;
-				case 4:
-					 breathespeed_flag=0;
-						W_PWM = 0;
-						C_PWM += 1;
-
-						if (C_PWM >= 100) {
-								direction = 5;
-						}
-						break;
-
-				case 5:
-					  breathespeed_flag=0;
-						W_PWM = 0;
-						C_PWM -= 1;
-						if (C_PWM <=1){
-								direction = 0;
-								driveMode=1;
-								W_PWM = 1;
-								C_PWM = 1;
-						}
-
-						break;
-				}
+static void neutral_breathe_fun(void)
+{
+	breathespeed_flag=1U;
+	if(direction==1U){
+		if(W_PWM>1U){ W_PWM--; C_PWM--; }
+		if(W_PWM<=1U){ W_PWM=1U; C_PWM=1U; direction=0U; }
+	}else{
+		if(W_PWM<68U){ W_PWM++; C_PWM++; }
+		if(W_PWM>=68U){ W_PWM=68U; C_PWM=68U; direction=1U; }
 	}
-	//UpdateDisplay();
-	UpdateDisplay_1();
 }
 
-
+void Mode1(void)
+{
+	if(choose_mode_falsg==3U){
+		breathespeed_flag=0U;
+		breathe_fun(&C_PWM,&W_PWM,0U);
+	}else if(choose_mode_falsg==4U){
+		breathespeed_flag=0U;
+		breathe_fun(&W_PWM,&C_PWM,0U);
+	}else if(choose_mode_falsg==5U){
+		neutral_breathe_fun();
+	}else if(choose_mode_falsg==6U){
+		switch(direction){
+			case 0U:
+				breathespeed_flag=0U;
+				W_PWM++; C_PWM=0U;
+				if(W_PWM>=100U){ W_PWM=100U; direction=1U; }
+				break;
+			case 1U:
+				breathespeed_flag=0U;
+				if(W_PWM>0U) W_PWM--;
+				C_PWM=0U;
+				if(W_PWM<=1U){ W_PWM=0U; direction=THREE_COLOR_WAIT_COLD; }
+				break;
+			case 4U:
+				breathespeed_flag=0U;
+				W_PWM=0U; C_PWM++;
+				if(C_PWM>=100U){ C_PWM=100U; direction=5U; }
+				break;
+			case 5U:
+				breathespeed_flag=0U;
+				W_PWM=0U;
+				if(C_PWM>0U) C_PWM--;
+				if(C_PWM<=1U){ C_PWM=0U; direction=THREE_COLOR_WAIT_NEUTRAL; }
+				break;
+			case 2U:
+				breathespeed_flag=1U;
+				W_PWM++; C_PWM++;
+				if(W_PWM>=68U){ W_PWM=68U; C_PWM=68U; direction=3U; }
+				break;
+			case 3U:
+				breathespeed_flag=1U;
+				if(W_PWM>0U) W_PWM--;
+				if(C_PWM>0U) C_PWM--;
+				if(W_PWM<=1U){ W_PWM=0U; C_PWM=0U; direction=THREE_COLOR_WAIT_WARM; }
+				break;
+			case THREE_COLOR_WAIT_COLD:
+				breathespeed_flag=0U; W_PWM=0U; C_PWM=0U;
+				if(W_PWM_duty==0U && C_PWM_duty==0U){
+					driveMode=2U; C_PWM=1U; direction=4U;
+				}
+				break;
+			case THREE_COLOR_WAIT_NEUTRAL:
+				breathespeed_flag=1U; W_PWM=0U; C_PWM=0U;
+				if(W_PWM_duty==0U && C_PWM_duty==0U){
+					driveMode=0U; W_PWM=1U; C_PWM=1U; direction=2U;
+				}
+				break;
+			case THREE_COLOR_WAIT_WARM:
+			default:
+				breathespeed_flag=0U; W_PWM=0U; C_PWM=0U;
+				if(W_PWM_duty==0U && C_PWM_duty==0U){
+					driveMode=1U; W_PWM=1U; direction=0U;
+				}
+				break;
+		}
+	}
+}
 void jump_fun(uint16_t *PWM_1, uint16_t *PWM_2, uint8_t flag){
 	if(flag==0){
 		*PWM_1 = 0;
@@ -280,8 +298,8 @@ void jump_fun(uint16_t *PWM_1, uint16_t *PWM_2, uint8_t flag){
 		}
 	}else if(flag==1){
 		if (!direction){
-				*PWM_1 = 40;
-				*PWM_2 = 40;
+				*PWM_1 = 50;
+				*PWM_2 = 50;
 				 direction = 1;
 			} else {
 				*PWM_1 = 0;
@@ -291,58 +309,117 @@ void jump_fun(uint16_t *PWM_1, uint16_t *PWM_2, uint8_t flag){
 	}
 }
 
-void Mode2(){ //跳变
-	  //printf("dd=%d--%d\r\n",W_PWM,W_PWM);
-		if(choose_mode_falsg==6){
-		  jump_fun(&C_PWM,&W_PWM,0); //暖光跳变
-		}else if(choose_mode_falsg==7){
-		  jump_fun(&W_PWM,&C_PWM,1); //中光跳变
-		}else if(choose_mode_falsg==8){
-		  jump_fun(&W_PWM,&C_PWM,0); //冷光跳变
-		}else if(choose_mode_falsg==9){
-				 switch (direction) {
-							case 1:
-									W_PWM =100;
-									C_PWM = 0;
-									direction = 2;
-									break;
-							case 2:
-									W_PWM = 0;
-									C_PWM = 0;
-									direction = 3;
-									driveMode=0;
-									break;
-							case 3:
-									W_PWM =40;
-									C_PWM =40;
-							    direction = 4;
-									break;
-							case 4:
-									W_PWM =0;
-									C_PWM =0;
-									direction = 5;
-								  driveMode=2;
-									break;
-							case 5:
-									W_PWM = 0;
-									C_PWM = 100;
-							  	direction = 6;
-									break;
-
-							case 6:
-									W_PWM = 0;
-									C_PWM = 0;
-									direction = 1;
-									driveMode=1;
-									break;
-							}
+void Mode2(void)
+{
+	if(choose_mode_falsg==9U){
+		jump_fun(&C_PWM,&W_PWM,0U);
+	}else if(choose_mode_falsg==10U){
+		jump_fun(&W_PWM,&C_PWM,0U);
+	}else if(choose_mode_falsg==11U){
+		jump_fun(&W_PWM,&C_PWM,1U);
+	}else if(choose_mode_falsg==12U){
+		switch(direction){
+			case 1U:
+				W_PWM=100U; C_PWM=0U; driveMode=1U; direction=2U;
+				break;
+			case 2U:
+				W_PWM=0U; C_PWM=100U; driveMode=2U; direction=3U;
+				break;
+			default:
+				W_PWM=50U; C_PWM=50U; driveMode=0U; direction=1U;
+				break;
 		}
-    UpdateDisplay_1();
+	}else if(choose_mode_falsg==13U){
+		switch(direction){
+			case 1U:
+				W_PWM=100U; C_PWM=0U; driveMode=1U; direction=2U;
+				break;
+			case 2U:
+				W_PWM=0U; C_PWM=0U; driveMode=2U; direction=3U;
+				break;
+			case 3U:
+				W_PWM=0U; C_PWM=100U; direction=4U;
+				break;
+			case 4U:
+				W_PWM=0U; C_PWM=0U; driveMode=0U; direction=5U;
+				break;
+			case 5U:
+				W_PWM=50U; C_PWM=50U; direction=6U;
+				break;
+			default:
+				W_PWM=0U; C_PWM=0U; driveMode=1U; direction=1U;
+				break;
+		}
+	}
 }
 
-void Mode3(){ //爆闪 //无
-		
-   UpdateDisplay();
+void Mode3(void)
+{
+	if(choose_mode_falsg==7U){
+		if(direction==1U){
+			if(C_PWM<100U) C_PWM++;
+			W_PWM=100U-C_PWM;
+			if(C_PWM>=100U){ C_PWM=100U; W_PWM=0U; direction=0U; }
+		}else{
+			if(C_PWM>0U) C_PWM--;
+			W_PWM=100U-C_PWM;
+			if(C_PWM==0U){ W_PWM=100U; direction=1U; }
+		}
+	}else if(choose_mode_falsg==8U){
+		switch(direction){
+			case 0U:
+				C_PWM=0U; driveMode=1U;
+				if(W_PWM>OVERLAP_GRADIENT_LEVEL) W_PWM--;
+				if(W_PWM<=OVERLAP_GRADIENT_LEVEL){ W_PWM=OVERLAP_GRADIENT_LEVEL; direction=1U; }
+				break;
+			case 1U:
+				if(W_PWM>0U){ W_PWM--; C_PWM++; }
+				driveMode=0U;
+				if(W_PWM==0U){ C_PWM=OVERLAP_GRADIENT_LEVEL; driveMode=2U; direction=2U; }
+				break;
+			case 2U:
+				W_PWM=0U; driveMode=2U;
+				if(C_PWM<100U) C_PWM++;
+				if(C_PWM>=100U){ C_PWM=100U; direction=3U; }
+				break;
+			case 3U:
+				W_PWM=0U; driveMode=2U;
+				if(C_PWM>OVERLAP_GRADIENT_LEVEL) C_PWM--;
+				if(C_PWM<=OVERLAP_GRADIENT_LEVEL){ C_PWM=OVERLAP_GRADIENT_LEVEL; direction=4U; }
+				break;
+			case 4U:
+				if(W_PWM<OVERLAP_NEUTRAL_LOW && C_PWM>OVERLAP_NEUTRAL_LOW){ W_PWM++; C_PWM--; }
+				driveMode=0U;
+				if(W_PWM>=OVERLAP_NEUTRAL_LOW){ W_PWM=OVERLAP_NEUTRAL_LOW; C_PWM=OVERLAP_NEUTRAL_LOW; direction=5U; }
+				break;
+			case 5U:
+				if(W_PWM<OVERLAP_NEUTRAL_PEAK){ W_PWM++; C_PWM++; }
+				driveMode=0U;
+				if(W_PWM>=OVERLAP_NEUTRAL_PEAK){ W_PWM=OVERLAP_NEUTRAL_PEAK; C_PWM=OVERLAP_NEUTRAL_PEAK; direction=6U; }
+				break;
+			case 6U:
+				if(W_PWM>OVERLAP_NEUTRAL_LOW){ W_PWM--; C_PWM--; }
+				driveMode=0U;
+				if(W_PWM<=OVERLAP_NEUTRAL_LOW){ W_PWM=OVERLAP_NEUTRAL_LOW; C_PWM=OVERLAP_NEUTRAL_LOW; direction=7U; }
+				break;
+			case 7U:
+				if(C_PWM>0U){ C_PWM--; W_PWM++; }
+				driveMode=0U;
+				if(C_PWM==0U){ W_PWM=OVERLAP_GRADIENT_LEVEL; driveMode=1U; direction=8U; }
+				break;
+			case 8U:
+			default:
+				C_PWM=0U; driveMode=1U;
+				if(W_PWM<100U) W_PWM++;
+				if(W_PWM>=100U){ W_PWM=100U; direction=0U; }
+				break;
+		}
+	}else{
+		return;
+	}
+	if(C_PWM==0U) driveMode=1U;
+	else if(W_PWM==0U) driveMode=2U;
+	else driveMode=0U;
 }
 pfunc modefunctin[] = { //模式切换，一共15个模式
 	Mode0,
@@ -351,6 +428,8 @@ pfunc modefunctin[] = { //ģʽ
 	Mode3,
 };
 void choice_mode(){
+		if(choose_mode_bh==0U) return;
+		if(Light_Transition_ModeActive || Light_Transition_FeedbackActive()) return;
 		if (!timer1.active && timer1.count == 0){ 
 							if(Mode==mode0){
 								startTimer(&timer1,1);
@@ -358,13 +437,13 @@ void choice_mode(){
 								if(breathespeed_flag==0){
 								  startTimer(&timer1,time_1[Speed]);
 								}else {
-								  startTimer(&timer1,time_1[Speed]+10);
+								  startTimer(&timer1,time_1_neutral[Speed]);
 								}
 							   	
 							}else if(Mode==mode2){
 								startTimer(&timer1,time_2[Speed]);
 							}else if(Mode==mode3){
-							   startTimer(&timer1,time_3[Speed]);//
+							   startTimer(&timer1,time_1[Speed]);//
 							}
 							
 							modefunctin[Mode]();

project/example/ble/ble_peripheral/app/src/Mode.h

@@ -13,6 +13,10 @@ extern "C" {
 #include <stdint.h>
 typedef void (*pfunc)(void);
 
+#define EFFECT_MODE_MIN         0U
+#define EFFECT_MODE_MAX         13U
+#define CUSTOM_TEMPERATURE_MODE 14U
+
 
 extern uint8_t deviceStatus;  //开机标志位
 extern uint8_t Mode;            //mode0 1 2 3 4

project/example/ble/ble_peripheral/app/src/PWM.c

@@ -31,7 +31,7 @@ pwm_ch_cap_type_t pwm_ch_cap_type;
 
 
 uint16_t timeCnt=0;
-uint16_t W_PWM = 10;//初始化暖光
+uint16_t W_PWM = 100;//初始化暖光
 uint16_t C_PWM = 0;
 
 
@@ -41,7 +41,7 @@ uint16_t deadTime_W = _deadTime;
 
 uint8_t  driveMode=1;
 uint8_t  PWMMAX=100;  //最大占空比
-uint8_t  Brightness=10;
+uint8_t  Brightness=BRIGHTNESS_MAX_PERCENT;
  // 切换 PWM 输出管脚,蓝牙调用此方法，切换设备输出线序
  
 uint16_t W_PWM_duty;//初始化暖光
@@ -56,31 +56,6 @@ void switch_pwm_pins(uint8_t red_pwm, uint8_t green_pwm, uint8_t blue_pwm)
 
 
 
- float  brightness_table[101] = {
-    0.006f, 0.006f, 0.006f, 0.006f, 0.006f,
-    0.006f, 0.006f, 0.006f, 0.007f, 0.008f,
-    0.009f, 0.010f, 0.011f, 0.013f, 0.015f,
-    0.018f, 0.020f, 0.023f, 0.026f, 0.029f,
-    0.032f, 0.036f, 0.039f, 0.043f, 0.047f,
-    0.052f, 0.056f, 0.061f, 0.066f, 0.071f,
-    0.076f, 0.082f, 0.087f, 0.093f, 0.099f,
-    0.106f, 0.112f, 0.119f, 0.126f, 0.133f,
-    0.141f, 0.148f, 0.156f, 0.164f, 0.173f,
-    0.181f, 0.190f, 0.199f, 0.208f, 0.218f,
-    0.227f, 0.237f, 0.247f, 0.258f, 0.268f,
-    0.279f, 0.290f, 0.302f, 0.313f, 0.325f,
-    0.337f, 0.349f, 0.362f, 0.375f, 0.388f,
-    0.401f, 0.414f, 0.428f, 0.442f, 0.456f,
-    0.471f, 0.485f, 0.500f, 0.516f, 0.531f,
-    0.547f, 0.563f, 0.579f, 0.595f, 0.612f,
-    0.629f, 0.646f, 0.664f, 0.681f, 0.699f,
-    0.718f, 0.736f, 0.755f, 0.774f, 0.793f,
-    0.813f, 0.832f, 0.852f, 0.873f, 0.893f,
-    0.914f, 0.935f, 0.957f, 0.978f, 1.000f,1.000f
-};
-
-
-
 void _PWM_INIT(){
 
 		GPIO_InitCfg_t GPIO_InitCfg = { 0 };  // 清零初始化配置结构体
@@ -115,37 +90,43 @@ void PWM_SetDuty(uint8_t PWMX ,uint8_t duty) {
 //	 }
 }
 
-void UpdateDisplay(void)  //静态更新 可以调节亮度
+static uint16_t scale_display_value(uint16_t value)
 {
-    W_PWM_duty = W_PWM * Brightness;
-    C_PWM_duty = C_PWM * Brightness;
-	 
+    if(value > 100U) value = 100U;
+    if(Brightness >= BRIGHTNESS_MAX_PERCENT) return value;
+    return (uint16_t)(((uint32_t)value * Brightness + 50U) / 100U);
 }
 
-void UpdateDisplay_1(void)  //动态更新 不可以调节亮度，只能调节速度
+void UpdateDisplay(void)  // static update with global brightness
 {
-    W_PWM_duty = W_PWM;
-    C_PWM_duty = C_PWM;
-	 // printf("dd=%d--%d--%d-%d-%d\r\n",choose_mode_falsg,W_PWM,C_PWM,driveMode,Brightness);
+    W_PWM_duty = scale_display_value(W_PWM);
+    C_PWM_duty = scale_display_value(C_PWM);
 }
 
-void temperature(uint8_t data)                                      //更新
+void UpdateDisplay_1(void)  // dynamic update with global brightness
 {
-	
-		driveMode=0;
-		if(data<57&&data>=16){C_PWM= 0;W_PWM = 10;driveMode=1;}
-		else if(data<77&&data>=57){C_PWM= 1;W_PWM = 7;}
-		else if(data<101&&data>=77){C_PWM= 2;W_PWM = 6;}
-		else if(data<123&&data>=101){C_PWM= 3;W_PWM = 5;}
-		else if(data<145&&data>=123){C_PWM= 4;W_PWM = 4;}
-		else if(data<167&&data>=145){C_PWM= 5;W_PWM = 3;}
-		else if(data<194&&data>=167){C_PWM= 6;W_PWM = 2;}
-		else if(data<210&&data>=194){C_PWM= 7;W_PWM = 1;}
-		else if(data>=210){C_PWM= 10;W_PWM = 0;driveMode=2;}
-		//printf("datat=%d-%d-%d\r\n",data,C_PWM,W_PWM);
-		//data = 0;
+    W_PWM_duty = scale_display_value(W_PWM);
+    C_PWM_duty = scale_display_value(C_PWM);
 }
 
+void temperature(uint8_t data)  // 0=cold, 255=warm
+{
+    W_PWM = (uint16_t)(((uint32_t)data * 100U + 127U) / 255U);
+    C_PWM = 100U - W_PWM;
+
+    if(W_PWM >= 100U)
+    {
+        driveMode = 1;
+    }
+    else if(C_PWM >= 100U)
+    {
+        driveMode = 2;
+    }
+    else
+    {
+        driveMode = 0;
+    }
+}
 /**
  * @brief       app_pwm_init
  * @details

project/example/ble/ble_peripheral/app/src/PWM.h

@@ -65,6 +65,13 @@ extern uint8_t driveMode;
 extern uint8_t PWMMAX;
 extern uint8_t Brightness;
 
+#define BRIGHTNESS_MIN_PERCENT     1U
+#define BRIGHTNESS_MAX_PERCENT     100U
+#define BRIGHTNESS_RF_STEP_PERCENT 10U
+
+#define SPEED_MIN_LEVEL 0U
+#define SPEED_MAX_LEVEL 9U
+
 
 #define DEVIATION_FREQ      10
 #define DEVIATION_DUTYCYCLE 10
@@ -136,6 +143,13 @@ void switch_pwm_pins(uint8_t red_pwm, uint8_t green_pwm, uint8_t blue_pwm);
 void adc_Init();
 void My_ADC_Get_Value();
 void gpio_pullup_input_inter_test();
+void Bridge_Init(void);
+void Bridge_Off(void);
+void Bridge_Service_1ms(void);
+void Bridge_Deadtime_Expired(void);
+void Bridge_FlashBlank_Request(void);
+uint8_t Bridge_FlashBlank_Ready(void);
+void Bridge_FlashBlank_Resume(void);
 #ifdef __cplusplus
 }
 #endif

project/example/ble/ble_peripheral/app/src/RF433.h

@@ -98,7 +98,7 @@
 //#define  RF_DATA        P15//RF433接收引脚,根据具体单片机定义引脚
 
 
-#define  RF_DATA        xc_gpio_read_pin(GPIO_5)		//RF433接收引脚,根据具体单片机定义引脚
+#define  RF_DATA        xc_gpio_read_pin(RF433_PIN)		//RF433接收引脚,根据具体单片机定义引脚
 
 #define  RF433_PIN      GPIO_5		//RF433接收引脚,根据具体单片机定义引脚
 #define  RF_dd          GPIO_0		//
@@ -188,7 +188,10 @@ void scan_433();
 void Lock_Pwm7xd();
 void Delay_50us();
 void Encoder_key();
+void rf433_clear_code(void);
+uint8_t rf433_start_pairing(void);
+void rf433_cancel_pairing(void);
+uint8_t rf433_paired_count(void);
 
 
 #endif
-

project/example/ble/ble_peripheral/app/src/Rf433.c

@@ -4,7 +4,11 @@
 #include "xc_drv_uart.h"
 #include "mode.h"
 #include "timer.h"
+#include "light_transition.h"
 #include "pwm.h"
+#include "rf433_decoder.h"
+#include "timeslice.h"
+#include "usr_server.h"
 union rf433_flag rf_flag = {0};
 unsigned char  high_level_time;
 unsigned char  low_level_time;
@@ -75,105 +79,344 @@ void rf433_gpio_init(){
 }
 
 static uint8_t ssse=0;
-uint8_t long_flag_s=0;
+static volatile uint16_t rf_frame_sequence;
+static uint16_t pair_last_frame_sequence;
+static uint32_t pair_candidate_data;
+static uint32_t pair_alternate_data;
+static uint8_t pair_candidate_valid;
+static uint8_t pair_alternate_count;
 
-// 在固定大小数组中添加新元素（滑动窗口）
-void addToFixedArray(uint8_t arr[], uint8_t newValue) {
-	uint8_t i;
-    // 所有元素向后移动一位
-    for( i = 4; i > 0; i--) {
-        arr[i] = arr[i - 1];
+static uint8_t pair_frame_silence_ticks;
+
+static uint8_t pairing_feedback_active;
+static uint8_t pairing_feedback_on;
+static uint8_t pairing_feedback_transitions;
+static uint16_t pairing_feedback_elapsed_ms;
+static uint16_t pairing_feedback_interval_ms;
+static uint8_t pair_deferred_command;
+static uint8_t pair_deferred_res_data;
+static uint32_t pair_deferred_receive_data;
+static uint8_t pair_command_replay;
+static uint8_t app_pairing_requested;
+
+#define PAIR_HOLD_FRAME_COUNT     4U
+#define PAIR_FRAME_SILENCE_TICKS 100U
+#define PAIRING_WINDOW_TICKS      50000UL
+#define RF433_RELEASE_TIMEOUT_TICKS 1500U
+#define RF433_MS_TO_SAMPLE_TICKS(ms) ((uint16_t)((ms) * (1000U / RF433_DECODER_SAMPLE_US)))
+#define RF433_MODE_REPEAT_TICKS   ((uint32_t)RF433_MS_TO_SAMPLE_TICKS(500U))
+uint8_t long_flag_s=0;
+static volatile uint32_t rf433_sample_ticks;
+static uint32_t rf433_mode_last_action_tick;
+static uint8_t rf433_mode_last_key;
+static uint8_t rf433_mode_action_valid;
+
+void _433_fun(void);
+
+// Keep paired addresses ordered from oldest to newest.
+static uint8_t Pairing_Address_IsEmpty(uint8_t high, uint8_t low)
+{
+    return ((high == 0U && low == 0U) ||
+            (high == 0xffU && low == 0xffU));
+}
+
+static uint8_t Pairing_Address_AddNew(uint8_t high, uint8_t low)
+{
+    uint8_t next_h[5];
+    uint8_t next_l[5];
+    uint8_t count = 0U;
+    uint8_t i;
+
+    for(i = 0U; i < 5U; i++)
+    {
+        if(adress_H_array[i] == high && adress_L_array[i] == low)
+        {
+            return 0U;
+        }
     }
 
-    // 在头部插入新值
-    arr[0] = newValue;
+    for(i = 0U; i < 5U; i++)
+    {
+        if(Pairing_Address_IsEmpty(adress_H_array[i], adress_L_array[i])) continue;
+
+        next_h[count] = adress_H_array[i];
+        next_l[count] = adress_L_array[i];
+        count++;
+    }
+
+    if(count >= 5U)
+    {
+        for(i = 0U; i < 4U; i++)
+        {
+            next_h[i] = next_h[i + 1U];
+            next_l[i] = next_l[i + 1U];
+        }
+        count = 4U;
+    }
+
+    next_h[count] = high;
+    next_l[count] = low;
+    count++;
+
+    for(i = 0U; i < 5U; i++)
+    {
+        if(i < count)
+        {
+            adress_H_array[i] = next_h[i];
+            adress_L_array[i] = next_l[i];
+        }
+        else
+        {
+            adress_H_array[i] = 0xffU;
+            adress_L_array[i] = 0xffU;
+        }
+    }
+
+    return 1U;
+}
+static void Pairing_Feedback_Apply(uint8_t on)
+{
+    Light_Transition_SetFeedback(1U, on);
+}
+
+static void Pairing_Feedback_Restore(void)
+{
+    Light_Transition_SetFeedback(0U, 0U);
+    if(deviceStatus == POWERON)
+    {
+        Light_Transition_BeginModeChange();
+        startTimer(&timer1, 1U);
+    }
+}
+
+static void Pairing_Feedback_Start(uint16_t interval_ms)
+{
+    if(pairing_feedback_active) return;
+
+    pair_deferred_command = 0U;
+
+    pairing_feedback_active = 1U;
+    pairing_feedback_on = 1U;
+    pairing_feedback_transitions = 6U;
+    pairing_feedback_elapsed_ms = 0U;
+    pairing_feedback_interval_ms = interval_ms;
+    Pairing_Feedback_Apply(1U);
+}
+
+static void Pairing_Feedback_Task(void)
+{
+    if(!pairing_feedback_active) return;
+
+    pairing_feedback_elapsed_ms += 3U;
+    if(pairing_feedback_elapsed_ms < pairing_feedback_interval_ms) return;
+    pairing_feedback_elapsed_ms = 0U;
+
+    if(pairing_feedback_transitions <= 1U)
+    {
+        pairing_feedback_active = 0U;
+        pairing_feedback_transitions = 0U;
+        Pairing_Feedback_Restore();
+        return;
+    }
+
+    pairing_feedback_transitions--;
+    pairing_feedback_on = pairing_feedback_on ? 0U : 1U;
+    Pairing_Feedback_Apply(pairing_feedback_on);
+}
+static uint8_t Pairing_IsTriggerCommand(uint8_t command)
+{
+    return command == Brightness_H || command == Brightness_L ||
+           command == B_Brightness_H || command == B_Brightness_L ||
+           command == F_Brightness_10 || command == F_Brightness_100;
+}
+
+static void Pairing_Replay_Deferred(void)
+{
+    uint8_t current_res_data;
+    uint32_t current_receive_data;
+
+    if(!pair_deferred_command) return;
+
+    current_res_data = res_data;
+    current_receive_data = receive_data;
+    res_data = pair_deferred_res_data;
+    receive_data = pair_deferred_receive_data;
+    pair_deferred_command = 0U;
+    pair_command_replay = 1U;
+    _433_fun();
+    pair_command_replay = 0U;
+    res_data = current_res_data;
+    receive_data = current_receive_data;
+}
+
+static void Pairing_Candidate_Reset(void)
+{
+    long_press_cnt = 0U;
+    pair_candidate_data = 0U;
+    pair_alternate_data = 0U;
+    pair_candidate_valid = 0U;
+    pair_alternate_count = 0U;
+    pair_frame_silence_ticks = 0U;
+    pair_deferred_command = 0U;
+}
+
+uint8_t rf433_paired_count(void)
+{
+    uint8_t count = 0U;
+    uint8_t i;
+
+    for(i = 0U; i < 5U; i++)
+    {
+        if(!Pairing_Address_IsEmpty(adress_H_array[i], adress_L_array[i]))
+            count++;
+    }
+    return count;
+}
+
+uint8_t rf433_start_pairing(void)
+{
+    if(pairing_feedback_active)
+    {
+        ble_remote_event_notify(0x0DU, 0U, rf433_paired_count());
+        return 0U;
+    }
+
+    ssse = 0U;
+    time_5s = 1U;
+    pair_last_frame_sequence = rf_frame_sequence;
+    Pairing_Candidate_Reset();
+    app_pairing_requested = 1U;
+    ble_remote_event_notify(0x0DU, 1U, rf433_paired_count());
+    return 1U;
+}
+
+void rf433_cancel_pairing(void)
+{
+    ssse = 1U;
+    time_5s = PAIRING_WINDOW_TICKS + 1U;
+    Pairing_Candidate_Reset();
+    if(app_pairing_requested)
+    {
+        app_pairing_requested = 0U;
+        ble_remote_event_notify(0x0DU, 0U, rf433_paired_count());
+    }
+}
+
+void rf433_clear_code(void)
+{
+    uint8_t i;
+
+    for(i = 0U; i < 5U; i++)
+    {
+        adress_H_array[i] = 0xffU;
+        adress_L_array[i] = 0xffU;
+    }
+
+    adress = 0U;
+    adress_H = 0U;
+    adress_L = 0U;
+    match_success = 0U;
+    ssse = 1U;
+    time_5s = PAIRING_WINDOW_TICKS + 1U;
+    Pairing_Candidate_Reset();
+    Pairing_Feedback_Start(200U);
+    app_pairing_requested = 0U;
+    set_TaskComps_timer(2U, 2000U);
+    ble_remote_event_notify(0x0EU, 1U, 0U);
 }
 
 
+
 static void Encoder_key_NoCode(){
-   uint8_t i=0,j=0,isok=0,updata=0; 
 	 uint16_t times_s=0; 
+	 uint8_t pairing_data_changed=0U;
 
-		if((res_data==Brightness_H||res_data==Brightness_L||res_data==B_Brightness_H||res_data==B_Brightness_L||res_data==F_Brightness_10||res_data==F_Brightness_100)&&time_5s<=40000&&ssse==0){
-       long_press_cnt++;
+        if(app_pairing_requested &&
+           (ssse != 0U || time_5s > PAIRING_WINDOW_TICKS))
+        {
+            app_pairing_requested = 0U;
+            ble_remote_event_notify(0x0DU, 0U, rf433_paired_count());
+        }
 	
-			if(long_press_cnt>200){
-				time_5s=40011;
-				ssse=1;
-				long_press_cnt=0;
+		if(pair_frame_silence_ticks < 0xffU) pair_frame_silence_ticks++;
+		if(pair_frame_silence_ticks > PAIR_FRAME_SILENCE_TICKS)
+        {
+            if(pair_candidate_valid &&
+               long_press_cnt < PAIR_HOLD_FRAME_COUNT)
+                Pairing_Replay_Deferred();
+            Pairing_Candidate_Reset();
+        }
+
+		if(rf_frame_sequence == pair_last_frame_sequence) return;
+		pair_last_frame_sequence = rf_frame_sequence;
+
+		if(ssse != 0U || time_5s > PAIRING_WINDOW_TICKS) return;
+		if(!(res_data==Brightness_H||res_data==Brightness_L||
+		     res_data==B_Brightness_H||res_data==B_Brightness_L||
+		     res_data==F_Brightness_10||res_data==F_Brightness_100))
+		{
+			return;
+		}
+
+		if(!pair_candidate_valid)
+		{
+			pair_candidate_data = receive_data;
+			pair_candidate_valid = 1U;
+			long_press_cnt = 1U;
+			pair_alternate_count = 0U;
+			pair_frame_silence_ticks = 0U;
+		}
+		else if(pair_candidate_data == receive_data)
+		{
+			long_press_cnt++;
+			pair_alternate_count = 0U;
+			pair_frame_silence_ticks = 0U;
+		}
+		else
+		{
+			if(pair_alternate_data == receive_data)
+			{
+				pair_alternate_count++;
+			}
+			else
+			{
+				pair_alternate_data = receive_data;
+				pair_alternate_count = 1U;
+			}
+
+			if(pair_alternate_count >= 2U)
+			{
+				pair_candidate_data = pair_alternate_data;
+				long_press_cnt = pair_alternate_count;
+				pair_alternate_count = 0U;
+				pair_frame_silence_ticks = 0U;
+			}
+		}
+
+			if(long_press_cnt>=PAIR_HOLD_FRAME_COUNT){
+                time_5s=PAIRING_WINDOW_TICKS + 1U;
+                ssse=1;
+                long_press_cnt=0;
+                pair_deferred_command=0U;
 	
 				if(res_data==Brightness_H||res_data==B_Brightness_H||res_data==F_Brightness_10){
-					  adress=receive_data >>8;
-					  adress_H = (receive_data >> 16) & 0xff;
-            adress_L = (receive_data >> 8) & 0xff;
-				// 第一步：检查是否已存在
-							for(j = 0; j <5; j++) {
-									if(adress_H_array[j] == adress_H && adress_L_array[j] == adress_L) { 
-										  isok=1;
-											break;
-									}		
-									
-							}
-								// 如果不存在，找空位添加
-								if(j==5) {  // 循环完整结束，说明不存在
-										// 寻找空位置（值为0的位置）
-										for(i = 0; i <=4; i++) {
-												if(adress_H_array[i] == 0 && adress_L_array[i] == 0) {
-														adress_H_array[i] = adress_H;
-														adress_L_array[i] = adress_L;
-													
-														isok=1;
-														break;
-												}
-												if(i==4){
-												for(j = 0; j <5; j++) {
-															if(adress_H_array[j] == adress_H && adress_L_array[j] == adress_L) { 
-																	updata=1;																
-																	break;
-															}
-													}
-												if(updata==0){
-													addToFixedArray(adress_H_array,adress_H); 
-													addToFixedArray(adress_L_array,adress_L); 	
-												}
-	
-												}
-												
-										}	
-								}		
-								times_s=300;	
-								match_success=1;
-								
-							   /// EA=0;
-									isok=0;
-									if(W_PWM==0&&C_PWM==0){
-										if(Mode==0){
-											W_PWM=10;
-									    C_PWM=0;
-										 UpdateDisplay();
-										}else {
-											W_PWM=10;
-									    C_PWM=0;
-										  UpdateDisplay_1();
-										}												    
-									}
-							   if(deviceStatus==POWEROFF){
-											 startTimer(&timer1,1);									 
-										   Start_PWM();
-									}
-									for (i=0;i<3;i++){
-												Start_PWM();
-												Delay_ms(times_s);
-											  Stop_PWM();
-												Delay_ms(times_s);	
-										}
-									
-									Start_PWM();
-							   	startTimer(&timer1,1);
-
-	
+					adress=receive_data >>8;
+					adress_H = (receive_data >> 16) & 0xff;
+					adress_L = (receive_data >> 8) & 0xff;
+					if(Pairing_Address_AddNew(adress_H, adress_L))
+					{
+						pairing_data_changed=1U;
+					}
+					else if(match_success==0U)
+					{
+						pairing_data_changed=1U;
+					}
+					times_s=300;
+					match_success=1;
+					Pairing_Feedback_Start(times_s);
 				}
 				   else if(res_data==Brightness_L||res_data==B_Brightness_L||res_data==F_Brightness_100){
+					  pairing_data_changed=1U;
                 	  adress_H_array[0] = 0xff;
 										adress_L_array[0] = 0xff;
 										adress_H_array[1] = 0xff;
@@ -188,37 +431,44 @@ static void Encoder_key_NoCode(){
 										times_s=200;	
 										match_success = 0;
 						 
-									if(W_PWM==0&&C_PWM==0){
-											W_PWM=10;
-									    C_PWM=0;
-										if(Mode==0){
-										  UpdateDisplay();
-										}else {
-										  UpdateDisplay_1();
-										}												    
-									}
-							   if(deviceStatus==POWEROFF){
-									 	  startTimer(&timer1,1);
-										  Start_PWM();
-									}
-									for (i=0;i<3;i++){
-												Start_PWM();
-												Delay_ms(times_s);
-												 Stop_PWM();
-												Delay_ms(times_s);	
-										}
-									 Start_PWM();
+									Pairing_Feedback_Start(times_s);
 				}
 			
 									 ssse=1;
-        set_TaskComps_timer(2,2000);
-		}
+        if(pairing_data_changed) set_TaskComps_timer(2,2000);
+        if(app_pairing_requested)
+        {
+            app_pairing_requested = 0U;
+            if(res_data==Brightness_H ||
+               res_data==B_Brightness_H ||
+               res_data==F_Brightness_10)
+                ble_remote_event_notify(0x0DU, 2U,
+                                        rf433_paired_count());
+            else
+                ble_remote_event_notify(0x0EU, 1U, 0U);
+        }
 		}
 }
 
 
+static void Rf433_Decoder_Frame_Poll(void)
+{
+    Rf433DecoderFrame_t frame;
+
+    if(!rf433_decoder_get_frame(&frame)) return;
+
+    receive_data = frame.code;
+    receive_temp = frame.code;
+    res_data = frame.key;
+    rf_frame_sequence++;
+    rf_flag.rf_receive_flag.receive_finish = 1U;
+    long_time = RF433_RELEASE_TIMEOUT_TICKS;
+}
+
 void Encoder_key(){
+  Rf433_Decoder_Frame_Poll();
   Encoder_key_NoCode();  //一对一
+  Pairing_Feedback_Task();
 }
 
 
@@ -241,110 +491,96 @@ static void  set_click(){
 		}
 }
 
-void rf433_receive(void)//rf433接收，查询周期100us
+static uint8_t rf433_is_mode_step_command(uint8_t command)
 {
-		
-    if (RF_DATA == LOW_LEVEL)
-    {
-        low_level_time++;//记录低电平时间
-        rf_flag.rf_receive_flag.current_level = 0; //当前电平状态
-    }
-    else if (RF_DATA == HIGH_LEVEL)
-    {
-        high_level_time++;//记录高电平时间
-					
-        if (!rf_flag.rf_receive_flag.current_level)//每个上升沿检测，0→1，一个完整的周期检测
-        {
-           // if ((high_level_time > 1 && high_level_time < 7) && (low_level_time > 115 && low_level_time < 125)) //判同步码，时间间隔12ms
-          //if ((high_level_time > 4 && high_level_time < 9) && ((low_level_time > 17 && low_level_time < 23))) //判同步码，时间间隔12ms 
-					 if ((high_level_time > 1 && high_level_time < 7) && (low_level_time > 115 && low_level_time < 130)) //判同步码，时间间隔12ms
-					{
-							//进来这里需要13ms
-                rf_flag.rf_receive_flag.sync_code = 1;//同步码接收成功标志
-                receive_data_cnt = 0;
-                receive_temp = 0;
-							  long_time=frames_time;
-						  
-            }
-            else if (rf_flag.rf_receive_flag.sync_code)//开始接收数据包
-            {
-							//if ((high_level_time > 1 && high_level_time < 9) && (low_level_time > 8 && low_level_time < 18)) //数据低电平
-							if ((high_level_time >= 1 && high_level_time <= 7) && (low_level_time >= 7 && low_level_time <= 16)) //数据低电平
-							{					
-                    receive_data_cnt++;//接收24位位数
-                    receive_temp = receive_temp << 1;
-                    if (receive_data_cnt == 24)//24位数据接收完成
-                    {
-											//进来这个if需要40ms
-                      rf_flag.rf_receive_flag.receive_finish = 1;//24位数据接收完成标志
-                      rf_flag.rf_receive_flag.sync_code = 0;	
-                      receive_data = receive_temp;//将接收到的编码复制到解码寄存器中
-										  res_data=receive_temp;
-                    }
-                }
-								//else if ((high_level_time > 7 && high_level_time < 18) && (low_level_time > 2 && low_level_time < 9)) //数据高电平
-								else if ((high_level_time >= 7 && high_level_time <= 16) && (low_level_time >= 2 && low_level_time<= 7)) //数据高电平
-								{			
-                    receive_temp = receive_temp << 1;
-                    receive_temp |= 1;
-                    receive_data_cnt++;
-                    if (receive_data_cnt == 24)
-                    {
-											//进来这个if需要40ms3748f3
-                        rf_flag.rf_receive_flag.receive_finish = 1;//24位数据接收完成标志
-                        rf_flag.rf_receive_flag.sync_code = 0;
-                        receive_data = receive_temp;//将接收到的编码复制到解码寄存器中
-											  res_data=receive_temp;
-                    }
-										
-                }
-                else
-                {
-                    rf_flag.rf_receive_flag.sync_code = 0;//接收失败 								
-                }
-								long_time=frames_time;//该值一定要大与68,68是指68ms通过逻辑分析仪测量一帧的时间
-//								
-//								
-							}
-						 if(long_time>0){ //一直按着会进入该if
-								//P05=0;  //433LED灯
-								long_time--;
-							  long_flag_s=0;
-							 if( KEY_STATE_re==1){
-								 if(time_300ms==0){
-								   time_300ms=Short_time;
-									 long_flag_s=1;
-									 KEY_STATE_re=0;
-								 }
-							   else if(time_300ms>0) time_300ms--;
-							 }
-						 }
-	           else { //松手
-							     time_300ms=LongPress_time;
-						       long_time=0;
-							     long_flag_s=0;
-							     Key_TypeDef.KEY_STATE_Click=0;
-							 		 KEY_STATE_re=0;			 
-						 }
-	
-            low_level_time = 0;//清零低电平时间
-            high_level_time = 1;//高电平时间开始计数
-						
-        }
-        rf_flag.rf_receive_flag.current_level = 1;//当前电平状态
-    }
-//		
-		if(time_5s<=40000){
-		   time_5s++;
-		}	
+    return command == Mode_add || command == Mode_dow;
 }
 
+/*
+ * Act immediately on the first valid mode frame. Repeated frames carrying
+ * the same key are accepted at most once every 500 ms. Keep this independent
+ * from the generic 150 ms release detector so an occasional missing RF frame
+ * cannot turn one physical hold into several rapid short presses.
+ */
+static uint8_t rf433_mode_step_ready(uint8_t command)
+{
+    uint32_t now = rf433_sample_ticks;
+
+    if(!rf433_mode_action_valid ||
+       rf433_mode_last_key != command ||
+       (uint32_t)(now - rf433_mode_last_action_tick) >=
+           RF433_MODE_REPEAT_TICKS)
+    {
+        rf433_mode_last_key = command;
+        rf433_mode_last_action_tick = now;
+        rf433_mode_action_valid = 1U;
+        return 1U;
+    }
+
+    return 0U;
+}
+
+void rf433_receive(void)//RF433 sample, called every 100 us
+{
+    rf433_sample_ticks++;
+    rf433_decoder_sample((RF_DATA == HIGH_LEVEL) ? 1U : 0U);
+
+    if(long_time > 0U)
+    {
+        long_time--;
+        long_flag_s = 0U;
+        if(KEY_STATE_re == 1U)
+        {
+            if(time_300ms == 0U)
+            {
+                time_300ms = RF433_MS_TO_SAMPLE_TICKS(Short_time);
+                long_flag_s = 1U;
+                KEY_STATE_re = 0U;
+            }
+            else
+            {
+                time_300ms--;
+            }
+        }
+    }
+    else
+    {
+        time_300ms = RF433_MS_TO_SAMPLE_TICKS(LongPress_time);
+        long_flag_s = 0U;
+        Key_TypeDef.KEY_STATE_Click = 0U;
+        KEY_STATE_re = 0U;
+    }
+
+    if(time_5s <= PAIRING_WINDOW_TICKS)
+    {
+        time_5s++;
+    }
+}
 uint16_t spee_dealy_time=0; //速度缓慢变换
 
+#define REMOTE_MODE_MIN 0U
+#define REMOTE_MODE_MAX EFFECT_MODE_MAX
+
 void _433_fun(){
-   if(Key_TypeDef.KEY_STATE_Click==1||KEY_STATE_re==1) return;
-	  set_click();
-	  sss=1;//记忆标志位
+   if(Light_Transition_FeedbackActive()) return;
+   if(!pair_command_replay && ssse == 0U &&
+      time_5s <= PAIRING_WINDOW_TICKS &&
+      Pairing_IsTriggerCommand(res_data))
+   {
+      pair_deferred_command = 1U;
+      pair_deferred_res_data = res_data;
+      pair_deferred_receive_data = receive_data;
+      return;
+   }
+   if(rf433_is_mode_step_command(res_data))
+   {
+      if(!rf433_mode_step_ready(res_data)) return;
+   }
+   else
+   {
+      if(Key_TypeDef.KEY_STATE_Click==1||KEY_STATE_re==1) return;
+      set_click();
+   }
 		switch(res_data){
 		//椭圆
 				case ON://单击
@@ -359,36 +595,58 @@ void _433_fun(){
 						break;
 				case Mode_add:
 					 if(POWEROFF==deviceStatus)break;
-						if(choose_mode_falsg!=0){  //遥控只是切换暖光，不跳模式
-									choose_mode_bh=0;
-									choose_mode_falsg=0;
-							   startTimer(&timer1,1);
+						if(choose_mode_falsg>REMOTE_MODE_MAX){
+								choose_mode_falsg=REMOTE_MODE_MIN;
+						}else if(choose_mode_falsg<REMOTE_MODE_MAX){
+								choose_mode_falsg++;
+						}else{
+								break;
 						}
+						choose_mode_bh=0;
+						startTimer(&timer1,1);
 						break;	
 				case Mode_dow:
 					 if(POWEROFF==deviceStatus)break;
-							if(choose_mode_falsg!=1){  //遥控只是切换冷光，不跳模式
-									choose_mode_bh=0;
-									choose_mode_falsg=1;
-								  startTimer(&timer1,1);
+						if(choose_mode_falsg>REMOTE_MODE_MAX){
+								choose_mode_falsg=REMOTE_MODE_MIN;
+						}else if(choose_mode_falsg>REMOTE_MODE_MIN){
+								choose_mode_falsg--;
+						}else{
+								break;
 						}
+						choose_mode_bh=0;
+						startTimer(&timer1,1);
 						break;
 				case Brightness_L:
 					 if(POWEROFF==deviceStatus)break;
 						if(Mode==mode0){
-								Brightness--;
-								if(Brightness<=2){Brightness=2;}
+								if(Brightness <=
+								   (BRIGHTNESS_MIN_PERCENT + BRIGHTNESS_RF_STEP_PERCENT))
+								{
+									Brightness = BRIGHTNESS_MIN_PERCENT;
+								}
+								else
+								{
+									Brightness -= BRIGHTNESS_RF_STEP_PERCENT;
+								}
 						}else {
-							  if(Speed<10)Speed++;
+							  if(Speed<SPEED_MAX_LEVEL)Speed++;
 						}
 						break;
 				case Brightness_H:
 					if(POWEROFF==deviceStatus)break;
 					 if(Mode==mode0){
-							  Brightness++;
-							if(Brightness>=10){Brightness=10;}
+							if(Brightness >=
+							   (BRIGHTNESS_MAX_PERCENT - BRIGHTNESS_RF_STEP_PERCENT))
+							{
+								Brightness = BRIGHTNESS_MAX_PERCENT;
+							}
+							else
+							{
+								Brightness += BRIGHTNESS_RF_STEP_PERCENT;
+							}
 				  	}else{
-							   if(Speed>1)Speed--;
+							   if(Speed>SPEED_MIN_LEVEL)Speed--;
 						}
 						break;
 				default:		
@@ -396,13 +654,14 @@ void _433_fun(){
 						if(res_data>=16&&res_data<=255){
 								Mode=mode0;
 							  choose_mode_bh=0;
-							  choose_mode_falsg=10;//圆环模式
+							  choose_mode_falsg=CUSTOM_TEMPERATURE_MODE;//圆环模式
 								driveMode=0;
-								temperature(res_data);
+								temperature((uint8_t)(((uint16_t)(255U - res_data) * 255U + 119U) / 239U));
 							  startTimer(&timer1,1);
 						}
 						break;
 		}				
+		set_TaskComps_timer(2U, 1000U);
 
 }
 
@@ -432,4 +691,3 @@ void scan_433(){
 
 
 
-

project/example/ble/ble_peripheral/app/src/app_task.c

@@ -15,6 +15,8 @@
 #include "app_sec.h"
 #include "app_task.h" // Application Manager Task API
 
+extern void ble_state_disconnect(void);
+
 
 #if APP_SCAN_FUNCTION
 extern void set_channel_scan(uint8_t channel);
@@ -703,6 +705,7 @@ static uint8_t gapc_callback(ke_msg_id_t const msgid, void const *param, ke_task
                 printf("app_start_advertising\n");
                 app_env.slave_conidx    = INVALID_DATA;
                 app_env.slave_connected = false;
+                ble_state_disconnect();
                 app_start_advertising();
             }
 

project/example/ble/ble_peripheral/app/src/arch_main.c

@@ -56,6 +56,8 @@
 #include "pwm.h"
 #include "mode.h"
 #include "RF433.h"    
+#include "rf433_decoder.h"
+#include "external_key.h"
 #include "rgblight.h"
 #include "timer.h"
 #include "fmc_spi.h"
@@ -238,7 +240,6 @@ void board_init()
 {
     clock_init();
 	  // app_uart_init();
-    rf433_gpio_init();
 #if (_DEBUG_ == 1)
     app_uart_init();
 #endif
@@ -389,17 +390,20 @@ int main(void)
 #endif
 	
 
-    wdt_init();
     /* Set the broadcast address of the device. */
     board_init();
 	  xc_fmc_spi_init_oprt( );
     xc_fmc_spi_flash_wake_up();
 	
 		fmc_spi_read();
+		power_restore_apply_on_boot();
+    /* Start the watchdog after the optional boot-time Flash update. */
+    wdt_init();
 		timer0_2_init();
     bluetooth_init();
 
 	 _PWM_INIT();
+	 Bridge_Init();
 	//	app_pwm_init();
 
 
@@ -448,6 +452,11 @@ int main(void)
 #endif
 	//	gpio_pullup_input_inter_test();
 		adc_Init();
+		external_key_init();
+		/* Keep RF433 GPIO initialization after the other input setup. */
+		rf433_gpio_init();
+		/* Clear any startup transition pulses after RF433 GPIO is stable. */
+		rf433_decoder_init();
     while (1){
 		 //DEBUG("222\r\n");
 			//printf("ddd=%d---%d---%d\r\n",W_PWM_duty,C_PWM_duty,(2*deadTime));

project/example/ble/ble_peripheral/app/src/bridge_pwm.c

@@ -0,0 +1,598 @@
+#include "pwm.h"
+#include "mode.h"
+#include "xc_drv_gpio.h"
+#include "xc_drv_pwm.h"
+#include "xc_drv_timer.h"
+#include "light_transition.h"
+
+/*
+ * External H-bridge input states:
+ *   W: GPIO_1 high/PWM, GPIO_2 low
+ *   C: GPIO_1 low, GPIO_2 high/PWM
+ * OFF: both low
+ *
+ * Single-color output uses a fixed 2 kHz hardware PWM.
+ *
+ * Dual-color output uses one fixed 500 us frame:
+ *   OFF -> W pulse -> OFF -> C pulse -> OFF to frame end.
+ * The available OFF time is distributed around both direction changes and
+ * each W/C transition retains at least 25 us protection.
+ * Normal dual-color output produces one pulse per color per frame (2 kHz).
+ * Only the low-output neutral section of three-color breathing uses PDM.
+ */
+#define BRIDGE_PWM_SCALE          1000U
+#define BRIDGE_PWM_PERIOD         6U
+#define BRIDGE_MIX_SCALE          1000U
+#define BRIDGE_FRAME_US           500U
+#define BRIDGE_DEADTIME_US        25U
+#define BRIDGE_DUAL_ACTIVE_US     450U
+#define BRIDGE_MIN_DUAL_PULSE_US  1U
+#define BRIDGE_NEUTRAL_PDM_PULSE_US 50U
+#define BRIDGE_TIMER_TICKS_PER_US 16U
+#define BRIDGE_PDM_THRESHOLD      (BRIDGE_MIX_SCALE * 4096UL)
+#define BRIDGE_NEUTRAL_PDM_THRESHOLD \
+    (BRIDGE_NEUTRAL_PDM_PULSE_US * BRIDGE_PDM_THRESHOLD)
+
+#define BRIDGE_GPIO_PORT          0U
+#define BRIDGE_GPIO_MASK          ((1UL << IO_PWM_W) | (1UL << IO_PWM_C))
+
+#define BRIDGE_TIMER3_TLC_REG     (*(volatile uint32_t *)0x4000303CUL)
+#define BRIDGE_TIMER3_TCR_REG     (*(volatile uint32_t *)0x40003044UL)
+
+#define BRIDGE_OFF                0U
+#define BRIDGE_W                  1U
+#define BRIDGE_C                  2U
+
+#define BRIDGE_MODE_OFF           0U
+#define BRIDGE_MODE_SINGLE        1U
+#define BRIDGE_MODE_DUAL          2U
+
+#define BRIDGE_STAGE_IDLE         0U
+#define BRIDGE_STAGE_START_SINGLE 1U
+#define BRIDGE_STAGE_START_W      2U
+#define BRIDGE_STAGE_END_W        3U
+#define BRIDGE_STAGE_START_C      4U
+#define BRIDGE_STAGE_END_C        5U
+
+#define BRIDGE_FLASH_BLANK_IDLE    0U
+#define BRIDGE_FLASH_BLANK_REQUEST 1U
+#define BRIDGE_FLASH_BLANK_READY   2U
+
+static volatile uint8_t active_state;
+static volatile uint8_t output_mode;
+static volatile uint8_t timer_stage;
+static volatile uint8_t flash_blank_state;
+static volatile uint8_t pending_single_state;
+static volatile uint16_t pending_single_duty;
+static volatile uint16_t frame_w_us;
+static volatile uint16_t frame_c_us;
+static volatile uint16_t frame_wc_off_us;
+static volatile uint16_t frame_cw_off_us;
+static volatile uint16_t next_w_us;
+static volatile uint16_t next_c_us;
+static volatile uint16_t next_wc_off_us;
+static volatile uint16_t next_cw_off_us;
+static volatile uint32_t next_pdm_w_step;
+static volatile uint32_t next_pdm_c_step;
+static volatile uint32_t next_pdm_threshold;
+static volatile uint8_t next_pdm_enabled;
+static volatile uint32_t pdm_w_accumulator;
+static volatile uint32_t pdm_c_accumulator;
+static volatile uint32_t frame_pdm_threshold;
+static volatile uint8_t frame_pdm_enabled;
+static volatile uint8_t frame_w_emit;
+static volatile uint8_t frame_c_emit;
+static uint16_t cached_w_mix = 0xFFFFU;
+static uint16_t cached_c_mix = 0xFFFFU;
+static uint8_t bridge_ready;
+
+__RAM_CODE static uint16_t clamp_mix_value(uint32_t value)
+{
+    return (value > BRIDGE_MIX_SCALE) ? BRIDGE_MIX_SCALE : (uint16_t)value;
+}
+
+static uint8_t pwm_index_for_state(uint8_t state)
+{
+    return (state == BRIDGE_W) ? PWM0_IDX : PWM1_IDX;
+}
+
+static void bridge_pin_low(uint8_t pin)
+{
+    xc_gpio_mux_ctl(pin, GPIO_Mux0);
+    xc_gpio_fun_sel(pin, GPIO_Dx);
+    xc_gpio_direction_config(pin, GPIO_DIR_OUTPUT);
+    xc_gpio_write_pin(pin, GPIO_PIN_RESET);
+}
+
+__RAM_CODE static void bridge_gpio_write(uint8_t state)
+{
+    uint32_t output = 0U;
+
+    if (state == BRIDGE_W) {
+        output = (1UL << IO_PWM_W);
+    } else if (state == BRIDGE_C) {
+        output = (1UL << IO_PWM_C);
+    } else {
+        state = BRIDGE_OFF;
+    }
+
+    /*
+     * GPIO_1 and GPIO_2 share port 0.  Write-enable bits update both pins
+     * atomically, so an intermediate 11 state cannot be generated.
+     */
+    gpio_port_dr_set(BRIDGE_GPIO_PORT,
+                     (BRIDGE_GPIO_MASK << DR_WE_LSB) | output);
+    active_state = state;
+}
+
+__RAM_CODE static void bridge_gpio_off(void)
+{
+    bridge_gpio_write(BRIDGE_OFF);
+}
+
+static void bridge_force_off(void)
+{
+    xc_pwm_stop(PWM0_IDX);
+    xc_pwm_stop(PWM1_IDX);
+    bridge_pin_low(IO_PWM_W);
+    bridge_pin_low(IO_PWM_C);
+    bridge_gpio_off();
+}
+
+__RAM_CODE static void bridge_gpio_state(uint8_t state)
+{
+    bridge_gpio_write(state);
+}
+
+__RAM_CODE static void bridge_timer_stop_fast(void)
+{
+    BRIDGE_TIMER3_TCR_REG = 0U;
+}
+
+__RAM_CODE static void bridge_timer_start(uint16_t duration_us)
+{
+    uint32_t ticks;
+
+    if (duration_us == 0U) {
+        duration_us = 1U;
+    }
+
+    ticks = (uint32_t)duration_us * BRIDGE_TIMER_TICKS_PER_US;
+    bridge_timer_stop_fast();
+    BRIDGE_TIMER3_TLC_REG = ticks;
+    BRIDGE_TIMER3_TCR_REG = 1U;
+}
+
+static void bridge_start_pwm(uint8_t state, uint16_t duty)
+{
+    uint8_t pwm_idx;
+    uint8_t pin;
+    GPIO_FUN_SEL_TypeDef function;
+
+    if (state != BRIDGE_W && state != BRIDGE_C) {
+        Bridge_Off();
+        return;
+    }
+
+    pwm_idx = pwm_index_for_state(state);
+    pin = (state == BRIDGE_W) ? IO_PWM_W : IO_PWM_C;
+    function = (state == BRIDGE_W) ? PWM0 : PWM1;
+
+    bridge_force_off();
+    xc_pwm_dutycycle_set(pwm_idx, BRIDGE_PWM_SCALE, duty);
+    xc_gpio_mux_ctl(pin, GPIO_Mux0);
+    xc_gpio_fun_sel(pin, function);
+    xc_pwm_start(pwm_idx);
+
+    active_state = state;
+    output_mode = BRIDGE_MODE_SINGLE;
+}
+
+void Bridge_Init(void)
+{
+    PWM_InitCfg_t pwm_cfg;
+    Timer_InitCfg_t timer_cfg;
+
+    pwm_cfg.SrcClk = PWM_CLK_SRC_32M_DIV;
+    pwm_cfg.DivClk = PWM_CLK_DIV0;
+    pwm_cfg.DutyCycleAcc = BRIDGE_PWM_SCALE;
+    pwm_cfg.DutyCycle = 0U;
+    pwm_cfg.SrcEnable = PWM_EN_SEL_SELF;
+    pwm_cfg.Period = BRIDGE_PWM_PERIOD;
+    pwm_cfg.InvertDelay = 0U;
+    pwm_cfg.InvertEnable = false;
+
+    pwm_cfg.OutputPin = IO_PWM_W;
+    pwm_cfg.OutputInvertPin = IO_PWM_C;
+    xc_pwm_init(PWM0_IDX, &pwm_cfg);
+
+    pwm_cfg.OutputPin = IO_PWM_C;
+    pwm_cfg.OutputInvertPin = IO_PWM_W;
+    xc_pwm_init(PWM1_IDX, &pwm_cfg);
+
+    timer_cfg.timer_src_clk = TIMER_CLK_SRC_32M_DIV;
+    timer_cfg.timer_div_clk = TIMER_DIV_CLK_16MHzOr16K;
+    timer_cfg.timer_mode = TIMER_MODE_SINGLE;
+    xc_timer_init(TIMER3_IDX, &timer_cfg);
+    NVIC_SetPriority((IRQn_Type)TIMER3_IRQn, 0);
+    NVIC_EnableIRQ(TIMER3_IRQn);
+
+    flash_blank_state = BRIDGE_FLASH_BLANK_IDLE;
+    bridge_ready = 1U;
+    Bridge_Off();
+}
+
+void Bridge_Off(void)
+{
+    xc_timer_stop(TIMER3_IDX);
+    timer_stage = BRIDGE_STAGE_IDLE;
+    pending_single_state = BRIDGE_OFF;
+    pending_single_duty = 0U;
+    frame_w_us = 0U;
+    frame_c_us = 0U;
+    frame_wc_off_us = 0U;
+    frame_cw_off_us = 0U;
+    next_w_us = 0U;
+    next_c_us = 0U;
+    next_wc_off_us = 0U;
+    next_cw_off_us = 0U;
+    next_pdm_w_step = 0U;
+    next_pdm_c_step = 0U;
+    next_pdm_threshold = 0U;
+    next_pdm_enabled = 0U;
+    pdm_w_accumulator = 0U;
+    pdm_c_accumulator = 0U;
+    frame_pdm_threshold = 0U;
+    frame_pdm_enabled = 0U;
+    frame_w_emit = 0U;
+    frame_c_emit = 0U;
+    cached_w_mix = 0xFFFFU;
+    cached_c_mix = 0xFFFFU;
+    bridge_force_off();
+    output_mode = BRIDGE_MODE_OFF;
+
+    if (flash_blank_state == BRIDGE_FLASH_BLANK_REQUEST)
+        flash_blank_state = BRIDGE_FLASH_BLANK_READY;
+}
+
+void Bridge_FlashBlank_Request(void)
+{
+    if (!bridge_ready ||
+        flash_blank_state != BRIDGE_FLASH_BLANK_IDLE)
+        return;
+
+    if (output_mode == BRIDGE_MODE_DUAL &&
+        timer_stage != BRIDGE_STAGE_IDLE) {
+        flash_blank_state = BRIDGE_FLASH_BLANK_REQUEST;
+        return;
+    }
+
+    flash_blank_state = BRIDGE_FLASH_BLANK_READY;
+}
+
+uint8_t Bridge_FlashBlank_Ready(void)
+{
+    return (flash_blank_state == BRIDGE_FLASH_BLANK_READY) ? 1U : 0U;
+}
+
+void Bridge_FlashBlank_Resume(void)
+{
+    if (flash_blank_state != BRIDGE_FLASH_BLANK_READY)
+        return;
+
+    flash_blank_state = BRIDGE_FLASH_BLANK_IDLE;
+}
+
+/*
+ * Flash page-program keeps global interrupts disabled. Poll Timer3 from the
+ * RAM-resident Flash busy loop so the software H-bridge frame continues.
+ */
+__RAM_CODE void xc_fmc_spi_flash_busy_hook(void)
+{
+    if (!bridge_ready ||
+        (deviceStatus == POWEROFF && !Light_Transition_FadeActive) ||
+        output_mode != BRIDGE_MODE_DUAL ||
+        timer_stage < BRIDGE_STAGE_START_W ||
+        timer_stage > BRIDGE_STAGE_END_C)
+        return;
+
+    if (timer_tis_get(TIMER3_IDX) != 0U) {
+        NVIC_ClearPendingIRQ((IRQn_Type)TIMER3_IRQn);
+        (void)timer_tic_get(TIMER3_IDX);
+        Bridge_Deadtime_Expired();
+    }
+}
+
+__RAM_CODE void Bridge_Deadtime_Expired(void)
+{
+    uint32_t w_step;
+    uint32_t c_step;
+    uint32_t pdm_threshold;
+    uint8_t pdm_enabled;
+
+    if (!bridge_ready ||
+        (deviceStatus == POWEROFF && !Light_Transition_FadeActive)) {
+        Bridge_Off();
+        return;
+    }
+
+    if (timer_stage == BRIDGE_STAGE_START_W) {
+        if (flash_blank_state == BRIDGE_FLASH_BLANK_REQUEST) {
+            flash_blank_state = BRIDGE_FLASH_BLANK_READY;
+        }
+
+        /*
+         * Latch all four durations together at the W boundary.  A brightness
+         * update can then never mix old and new timings inside one frame.
+         */
+        frame_w_us = next_w_us;
+        frame_c_us = next_c_us;
+        frame_wc_off_us = next_wc_off_us;
+        frame_cw_off_us = next_cw_off_us;
+        pdm_enabled = next_pdm_enabled;
+        w_step = next_pdm_w_step;
+        c_step = next_pdm_c_step;
+        pdm_threshold = next_pdm_threshold;
+
+        if (pdm_enabled &&
+            (!frame_pdm_enabled ||
+             frame_pdm_threshold != pdm_threshold)) {
+            pdm_w_accumulator = pdm_threshold - w_step;
+            /*
+             * A 50:50 neutral target gives W and C identical PDM steps.
+             * Start C half a density cycle away from W so their optical
+             * pulses are spread across different frames instead of arriving
+             * as one bright pair followed by a long dark gap.
+             */
+            if (pdm_threshold == BRIDGE_NEUTRAL_PDM_THRESHOLD)
+                pdm_c_accumulator = pdm_threshold / 2U;
+            else
+                pdm_c_accumulator = pdm_threshold - c_step;
+        }
+        frame_pdm_enabled = pdm_enabled;
+        frame_pdm_threshold = pdm_enabled ? pdm_threshold : 0U;
+
+        if (frame_pdm_enabled) {
+            pdm_w_accumulator += w_step;
+            if (pdm_w_accumulator >= frame_pdm_threshold) {
+                pdm_w_accumulator -= frame_pdm_threshold;
+                frame_w_emit = 1U;
+            } else {
+                frame_w_emit = 0U;
+            }
+
+            pdm_c_accumulator += c_step;
+            if (pdm_c_accumulator >= frame_pdm_threshold) {
+                pdm_c_accumulator -= frame_pdm_threshold;
+                frame_c_emit = 1U;
+            } else {
+                frame_c_emit = 0U;
+            }
+        } else {
+            pdm_w_accumulator = 0U;
+            pdm_c_accumulator = 0U;
+            frame_w_emit = 1U;
+            frame_c_emit = 1U;
+        }
+
+        if (frame_w_emit)
+            bridge_gpio_state(BRIDGE_W);
+        else
+            bridge_gpio_off();
+        timer_stage = BRIDGE_STAGE_END_W;
+        bridge_timer_start(frame_w_us);
+    } else if (timer_stage == BRIDGE_STAGE_END_W) {
+        bridge_gpio_off();
+        timer_stage = BRIDGE_STAGE_START_C;
+        bridge_timer_start(frame_wc_off_us);
+    } else if (timer_stage == BRIDGE_STAGE_START_C) {
+        if (frame_c_emit)
+            bridge_gpio_state(BRIDGE_C);
+        else
+            bridge_gpio_off();
+        timer_stage = BRIDGE_STAGE_END_C;
+        bridge_timer_start(frame_c_us);
+    } else if (timer_stage == BRIDGE_STAGE_END_C) {
+        bridge_gpio_off();
+        timer_stage = BRIDGE_STAGE_START_W;
+        bridge_timer_start(frame_cw_off_us);
+    } else if (timer_stage == BRIDGE_STAGE_START_SINGLE) {
+        timer_stage = BRIDGE_STAGE_IDLE;
+        bridge_start_pwm(pending_single_state, pending_single_duty);
+    } else {
+        Bridge_Off();
+    }
+}
+
+__RAM_CODE void Bridge_Service_1ms(void)
+{
+    uint32_t w_mix;
+    uint32_t c_mix;
+    uint32_t total;
+    uint32_t total_on_us;
+    uint32_t total_off_us;
+    uint32_t pdm_w_step;
+    uint32_t pdm_c_step;
+    uint16_t pwm_duty;
+    uint8_t single_state;
+
+    if (flash_blank_state != BRIDGE_FLASH_BLANK_IDLE)
+        return;
+
+    if (!bridge_ready ||
+        (deviceStatus == POWEROFF && !Light_Transition_FadeActive)) {
+        if (output_mode != BRIDGE_MODE_OFF || timer_stage != BRIDGE_STAGE_IDLE) {
+            Bridge_Off();
+        }
+        return;
+    }
+
+    w_mix = clamp_mix_value(W_PWM_duty);
+    c_mix = clamp_mix_value(C_PWM_duty);
+    total = w_mix + c_mix;
+
+    /*
+     * Below a physical 1 us pulse, keep the pulse width valid and distribute
+     * 1 us pulses across 2 kHz frames. This extends a mixed-light power-off
+     * fade below the normal timer resolution without creating sub-us edges.
+     */
+    pdm_w_step =
+        BRIDGE_DUAL_ACTIVE_US * Light_Transition_W_Output_Q12;
+    pdm_c_step =
+        BRIDGE_DUAL_ACTIVE_US * Light_Transition_C_Output_Q12;
+    if (deviceStatus == POWEROFF && Light_Transition_FadeActive &&
+        pdm_w_step != 0U && pdm_c_step != 0U &&
+        pdm_w_step < BRIDGE_PDM_THRESHOLD &&
+        pdm_c_step < BRIDGE_PDM_THRESHOLD) {
+        next_w_us = BRIDGE_MIN_DUAL_PULSE_US;
+        next_c_us = BRIDGE_MIN_DUAL_PULSE_US;
+        total_off_us =
+            BRIDGE_FRAME_US - (2U * BRIDGE_MIN_DUAL_PULSE_US);
+        next_wc_off_us = (uint16_t)(total_off_us / 2U);
+        next_cw_off_us =
+            (uint16_t)(total_off_us - next_wc_off_us);
+        next_pdm_w_step = pdm_w_step;
+        next_pdm_c_step = pdm_c_step;
+        next_pdm_threshold = BRIDGE_PDM_THRESHOLD;
+        next_pdm_enabled = 1U;
+        cached_w_mix = (uint16_t)w_mix;
+        cached_c_mix = (uint16_t)c_mix;
+        goto dual_output_ready;
+    }
+
+    /*
+     * In the neutral part of three-color breathing, keep each W/C pulse at
+     * a reliable 50 us and reduce only its frame density below that level.
+     * Single-color breathing never enters this branch and stays on hardware
+     * PWM all the way down to zero.
+     */
+    if (deviceStatus != POWEROFF &&
+        Mode == mode1 &&
+        (choose_mode_falsg == 5U || choose_mode_falsg == 6U) &&
+        w_mix != 0U && c_mix != 0U) {
+        pdm_w_step =
+            BRIDGE_DUAL_ACTIVE_US * ((uint32_t)w_mix << 12);
+        pdm_c_step =
+            BRIDGE_DUAL_ACTIVE_US * ((uint32_t)c_mix << 12);
+
+        if (pdm_w_step < BRIDGE_NEUTRAL_PDM_THRESHOLD &&
+            pdm_c_step < BRIDGE_NEUTRAL_PDM_THRESHOLD) {
+            next_w_us = BRIDGE_NEUTRAL_PDM_PULSE_US;
+            next_c_us = BRIDGE_NEUTRAL_PDM_PULSE_US;
+            total_off_us =
+                BRIDGE_FRAME_US -
+                (2U * BRIDGE_NEUTRAL_PDM_PULSE_US);
+            next_wc_off_us = (uint16_t)(total_off_us / 2U);
+            next_cw_off_us =
+                (uint16_t)(total_off_us - next_wc_off_us);
+            next_pdm_w_step = pdm_w_step;
+            next_pdm_c_step = pdm_c_step;
+            next_pdm_threshold = BRIDGE_NEUTRAL_PDM_THRESHOLD;
+            next_pdm_enabled = 1U;
+            cached_w_mix = (uint16_t)w_mix;
+            cached_c_mix = (uint16_t)c_mix;
+            goto dual_output_ready;
+        }
+    }
+
+    if (next_pdm_enabled) {
+        cached_w_mix = 0xFFFFU;
+        cached_c_mix = 0xFFFFU;
+    }
+    next_pdm_enabled = 0U;
+    next_pdm_w_step = 0U;
+    next_pdm_c_step = 0U;
+    next_pdm_threshold = 0U;
+
+    if (total == 0U) {
+        Bridge_Off();
+        return;
+    }
+
+    if (total > BRIDGE_MIX_SCALE) {
+        w_mix = (w_mix * BRIDGE_MIX_SCALE) / total;
+        c_mix = BRIDGE_MIX_SCALE - w_mix;
+        total = BRIDGE_MIX_SCALE;
+    }
+
+    /* Keep the verified fixed 2 kHz hardware PWM for a single color. */
+    if (w_mix == 0U || c_mix == 0U) {
+        single_state = (w_mix != 0U) ? BRIDGE_W : BRIDGE_C;
+        pwm_duty = (uint16_t)((total * BRIDGE_PWM_SCALE +
+                               (BRIDGE_MIX_SCALE / 2U)) / BRIDGE_MIX_SCALE);
+        /*
+         * Use the same 450 us maximum energy as mixed light for every
+         * single-color output. Switching between the hardware-PWM and
+         * Timer3 mixed-light paths therefore does not change total energy.
+         */
+        pwm_duty = (uint16_t)(
+            ((uint32_t)pwm_duty * BRIDGE_DUAL_ACTIVE_US +
+             (BRIDGE_FRAME_US / 2U)) / BRIDGE_FRAME_US);
+
+        if (output_mode == BRIDGE_MODE_SINGLE &&
+            active_state == single_state &&
+            timer_stage == BRIDGE_STAGE_IDLE) {
+            xc_pwm_dutycycle_set(pwm_index_for_state(single_state),
+                                 BRIDGE_PWM_SCALE, pwm_duty);
+            return;
+        }
+
+        xc_timer_stop(TIMER3_IDX);
+        timer_stage = BRIDGE_STAGE_START_SINGLE;
+        pending_single_state = single_state;
+        pending_single_duty = pwm_duty;
+        bridge_force_off();
+        output_mode = BRIDGE_MODE_OFF;
+        bridge_timer_start(BRIDGE_DEADTIME_US);
+        return;
+    }
+
+    if (cached_w_mix != w_mix || cached_c_mix != c_mix ||
+        output_mode != BRIDGE_MODE_DUAL) {
+        /*
+         * Keep 50 us OFF at maximum dual-color brightness. The OFF time is
+         * split evenly between W->C and C->W, which both absorbs interrupt
+         * latency and spreads the two optical pulses across the 500 us frame.
+         */
+        total_on_us = (BRIDGE_DUAL_ACTIVE_US * total +
+                       (BRIDGE_MIX_SCALE / 2U)) / BRIDGE_MIX_SCALE;
+        /* Keep a non-zero timer interval without imposing a brightness floor. */
+        if (total_on_us < (2U * BRIDGE_MIN_DUAL_PULSE_US)) {
+            total_on_us = 2U * BRIDGE_MIN_DUAL_PULSE_US;
+        }
+
+        next_w_us = (uint16_t)((total_on_us * w_mix +
+                                (total / 2U)) / total);
+        if (next_w_us < BRIDGE_MIN_DUAL_PULSE_US) {
+            next_w_us = BRIDGE_MIN_DUAL_PULSE_US;
+        } else if (next_w_us >
+                   total_on_us - BRIDGE_MIN_DUAL_PULSE_US) {
+            next_w_us =
+                (uint16_t)(total_on_us - BRIDGE_MIN_DUAL_PULSE_US);
+        }
+        next_c_us = (uint16_t)(total_on_us - next_w_us);
+
+        total_off_us = BRIDGE_FRAME_US - total_on_us;
+        next_wc_off_us = (uint16_t)(total_off_us / 2U);
+        next_cw_off_us = (uint16_t)(total_off_us - next_wc_off_us);
+
+        cached_w_mix = (uint16_t)w_mix;
+        cached_c_mix = (uint16_t)c_mix;
+    }
+
+dual_output_ready:
+    if (output_mode == BRIDGE_MODE_DUAL &&
+        timer_stage != BRIDGE_STAGE_IDLE) {
+        return;
+    }
+
+    /*
+     * Timer3 owns the complete repeating frame, including both full direction
+     * deadtimes. Timer0 only publishes updated brightness/mix parameters.
+     */
+    bridge_timer_stop_fast();
+    timer_stage = BRIDGE_STAGE_START_W;
+    bridge_force_off();
+    output_mode = BRIDGE_MODE_DUAL;
+    bridge_timer_start(next_cw_off_us);
+}

project/example/ble/ble_peripheral/app/src/external_key.c

@@ -0,0 +1,278 @@
+#include "external_key.h"
+#include "xc_drv_gpio.h"
+#include "Mode.h"
+#include "PWM.h"
+#include "RF433.h"
+#include "timer.h"
+#include "timeslice.h"
+
+#define EXTERNAL_KEY_PIN                 GPIO_5
+#define EXTERNAL_KEY_PRESSED_LEVEL       GPIO_PIN_RESET
+
+/* external_key_scan is called every 10 ms. */
+#define EXT_KEY_DEBOUNCE_TICKS           2U
+#define EXT_KEY_DOUBLE_TICKS             15U
+#define EXT_KEY_LONG_TICKS               40U
+#define EXT_KEY_BRIGHTNESS_STEP_TICKS    5U
+#define EXT_KEY_SPEED_STEP_TICKS         15U
+#define EXT_KEY_CLEAR_CODE_TICKS          3000U
+
+#define EXT_KEY_BRIGHTNESS_STEP          3U
+#define EXT_KEY_SPEED_STEP               1U
+#define EXT_KEY_SAVE_DELAY_MS            1000U
+
+typedef enum
+{
+    EXT_KEY_IDLE = 0,
+    EXT_KEY_DOWN,
+    EXT_KEY_WAIT_SECOND,
+    EXT_KEY_SECOND_DOWN,
+    EXT_KEY_LONG
+} EXT_KEY_STATE;
+
+static EXT_KEY_STATE ext_key_state = EXT_KEY_IDLE;
+static uint16_t ext_key_press_ticks;
+static uint16_t ext_key_wait_ticks;
+static uint16_t ext_key_step_ticks;
+static uint8_t ext_key_direction_up = 1U;
+static uint8_t ext_key_adjust_speed;
+static uint8_t ext_key_clear_triggered;
+
+static uint8_t external_key_is_pressed(void)
+{
+    return xc_gpio_read_pin(EXTERNAL_KEY_PIN) ==
+           EXTERNAL_KEY_PRESSED_LEVEL;
+}
+
+static void external_key_save_later(void)
+{
+    set_TaskComps_timer(2U, EXT_KEY_SAVE_DELAY_MS);
+}
+
+static void external_key_power_toggle(void)
+{
+    if(deviceStatus == POWEROFF)
+        Start_PWM();
+    else
+        Stop_PWM();
+
+    external_key_save_later();
+}
+
+static void external_key_mode_next(void)
+{
+    if(deviceStatus == POWEROFF)
+        Start_PWM();
+
+    if(choose_mode_falsg >= EFFECT_MODE_MAX)
+        choose_mode_falsg = EFFECT_MODE_MIN;
+    else
+        choose_mode_falsg++;
+
+    choose_mode_bh = 0U;
+    startTimer(&timer1, 1U);
+    external_key_save_later();
+}
+
+static void external_key_brightness_step(void)
+{
+    if(ext_key_direction_up)
+    {
+        if(Brightness >=
+           (BRIGHTNESS_MAX_PERCENT - EXT_KEY_BRIGHTNESS_STEP))
+            Brightness = BRIGHTNESS_MAX_PERCENT;
+        else
+            Brightness += EXT_KEY_BRIGHTNESS_STEP;
+    }
+    else
+    {
+        if(Brightness <=
+           (BRIGHTNESS_MIN_PERCENT + EXT_KEY_BRIGHTNESS_STEP))
+            Brightness = BRIGHTNESS_MIN_PERCENT;
+        else
+            Brightness -= EXT_KEY_BRIGHTNESS_STEP;
+    }
+}
+
+static void external_key_speed_step(void)
+{
+    /*
+     * A smaller Speed value is faster in the current effect tables.
+     * Keep the same direction convention used by DWM11.
+     */
+    if(ext_key_direction_up)
+    {
+        if(Speed > SPEED_MIN_LEVEL)
+            Speed -= EXT_KEY_SPEED_STEP;
+    }
+    else
+    {
+        if(Speed < SPEED_MAX_LEVEL)
+            Speed += EXT_KEY_SPEED_STEP;
+    }
+}
+
+static void external_key_adjust_step(void)
+{
+    if(deviceStatus == POWEROFF)
+        Start_PWM();
+
+    if(ext_key_adjust_speed)
+        external_key_speed_step();
+    else
+        external_key_brightness_step();
+}
+
+static void external_key_long_start(void)
+{
+    ext_key_adjust_speed = (Mode == mode0) ? 0U : 1U;
+    ext_key_step_ticks = 0U;
+    external_key_adjust_step();
+}
+
+static void external_key_long_stop(void)
+{
+    if(ext_key_clear_triggered)
+    {
+        ext_key_clear_triggered = 0U;
+        ext_key_adjust_speed = 0U;
+        return;
+    }
+
+    external_key_save_later();
+    ext_key_direction_up = ext_key_direction_up ? 0U : 1U;
+    ext_key_adjust_speed = 0U;
+}
+
+void external_key_init(void)
+{
+    GPIO_InitCfg_t gpio_cfg = {0};
+
+    gpio_cfg.Mux = GPIO_Mux0;
+    gpio_cfg.FunSel = GPIO_Dx;
+    gpio_cfg.Pull = GPIO_PULLUP;
+    gpio_cfg.Dir = GPIO_DIR_INPUT;
+    gpio_cfg.Int = NOT_INT;
+    gpio_cfg.Pin = EXTERNAL_KEY_PIN;
+    xc_gpio_init(&gpio_cfg);
+}
+
+void external_key_scan(void)
+{
+    uint8_t pressed = external_key_is_pressed();
+    uint16_t step_period;
+
+    switch(ext_key_state)
+    {
+        case EXT_KEY_IDLE:
+            if(pressed)
+            {
+                ext_key_press_ticks = 1U;
+                ext_key_step_ticks = 0U;
+                ext_key_clear_triggered = 0U;
+                ext_key_state = EXT_KEY_DOWN;
+            }
+            break;
+
+        case EXT_KEY_DOWN:
+            if(pressed)
+            {
+                if(ext_key_press_ticks < 0xFFFFU)
+                    ext_key_press_ticks++;
+
+                if(ext_key_press_ticks >= EXT_KEY_LONG_TICKS)
+                {
+                    external_key_long_start();
+                    ext_key_state = EXT_KEY_LONG;
+                }
+            }
+            else
+            {
+                if(ext_key_press_ticks >= EXT_KEY_DEBOUNCE_TICKS)
+                {
+                    ext_key_wait_ticks = 0U;
+                    ext_key_state = EXT_KEY_WAIT_SECOND;
+                }
+                else
+                {
+                    ext_key_state = EXT_KEY_IDLE;
+                }
+            }
+            break;
+
+        case EXT_KEY_WAIT_SECOND:
+            if(pressed)
+            {
+                ext_key_press_ticks = 1U;
+                ext_key_step_ticks = 0U;
+                ext_key_clear_triggered = 0U;
+                ext_key_state = EXT_KEY_SECOND_DOWN;
+            }
+            else
+            {
+                ext_key_wait_ticks++;
+                if(ext_key_wait_ticks >= EXT_KEY_DOUBLE_TICKS)
+                {
+                    external_key_power_toggle();
+                    ext_key_state = EXT_KEY_IDLE;
+                }
+            }
+            break;
+
+        case EXT_KEY_SECOND_DOWN:
+            if(pressed)
+            {
+                if(ext_key_press_ticks < 0xFFFFU)
+                    ext_key_press_ticks++;
+
+                if(ext_key_press_ticks >= EXT_KEY_LONG_TICKS)
+                {
+                    external_key_long_start();
+                    ext_key_state = EXT_KEY_LONG;
+                }
+            }
+            else
+            {
+                if(ext_key_press_ticks >= EXT_KEY_DEBOUNCE_TICKS)
+                    external_key_mode_next();
+                ext_key_state = EXT_KEY_IDLE;
+            }
+            break;
+
+        case EXT_KEY_LONG:
+            if(pressed)
+            {
+                if(ext_key_press_ticks < 0xFFFFU)
+                    ext_key_press_ticks++;
+
+                if(!ext_key_clear_triggered &&
+                   ext_key_press_ticks >= EXT_KEY_CLEAR_CODE_TICKS)
+                {
+                    ext_key_clear_triggered = 1U;
+                    rf433_clear_code();
+                }
+                else if(!ext_key_clear_triggered)
+                {
+                    step_period = ext_key_adjust_speed ?
+                        EXT_KEY_SPEED_STEP_TICKS :
+                        EXT_KEY_BRIGHTNESS_STEP_TICKS;
+                    ext_key_step_ticks++;
+                    if(ext_key_step_ticks >= step_period)
+                    {
+                        ext_key_step_ticks = 0U;
+                        external_key_adjust_step();
+                    }
+                }
+            }
+            else
+            {
+                external_key_long_stop();
+                ext_key_state = EXT_KEY_IDLE;
+            }
+            break;
+
+        default:
+            ext_key_state = EXT_KEY_IDLE;
+            break;
+    }
+}

project/example/ble/ble_peripheral/app/src/external_key.h

@@ -0,0 +1,7 @@
+#ifndef _EXTERNAL_KEY_H_
+#define _EXTERNAL_KEY_H_
+
+void external_key_init(void);
+void external_key_scan(void);
+
+#endif

project/example/ble/ble_peripheral/app/src/fmc_spi.c

@@ -33,6 +33,7 @@
 #include "PWM.h"
 #include "RF433.h"
 #include "xc60xx.h"
+#include "timeslice.h"
 
 /*------------------------------------------------------------------------------------
 	                                    Macros
@@ -69,6 +70,20 @@ unsigned char get_checksum(unsigned char *ptrdata, unsigned char length)
 	return CheckSum;
 }
 
+#define FLASH_BRIGHTNESS_FORMAT_INDEX  14U
+#define FLASH_BRIGHTNESS_PERCENT_MARK  0xA5U
+#define FLASH_MODE_LAYOUT_INDEX        26U
+#define FLASH_MODE_LAYOUT_MARK         0xA6U
+#define FLASH_POWER_MODE_MARK_INDEX    27U
+#define FLASH_POWER_MODE_INDEX         28U
+#define FLASH_POWER_CYCLE_INDEX        29U
+#define FLASH_POWER_MODE_MARK          0xA7U
+#define POWER_POLICY_SAVE_DELAY_MS     100U
+#define USER_DATA_FLASH_ADDR           0x1E000UL
+
+uint8_t power_restore_policy = POWER_RESTORE_CYCLE_STATIC;
+static uint8_t power_cycle_next_mode;
+
 void read_user_data(void)
 {
 
@@ -78,12 +93,40 @@ void read_user_data(void)
 			
 				Mode          = r_data[2];
 				Brightness    = r_data[3];
+
+				/*
+				 * Firmware before the percent-brightness update stored 2..10.
+				 * Byte 14 was unused, so use it as an explicit format marker.
+				 */
+				if(r_data[FLASH_BRIGHTNESS_FORMAT_INDEX] !=
+				   FLASH_BRIGHTNESS_PERCENT_MARK)
+				{
+					if(Brightness >= 2U && Brightness <= 10U)
+						Brightness = (uint8_t)(Brightness * 10U);
+					else
+						Brightness = BRIGHTNESS_MAX_PERCENT;
+				}
+				if(Brightness < BRIGHTNESS_MIN_PERCENT)
+					Brightness = BRIGHTNESS_MIN_PERCENT;
+				else if(Brightness > BRIGHTNESS_MAX_PERCENT)
+					Brightness = BRIGHTNESS_MAX_PERCENT;
+
 		  	Speed        = r_data[7];
+				if(Speed > SPEED_MAX_LEVEL)
+					Speed = SPEED_MAX_LEVEL;
 				deviceStatus  = r_data[8];
 
 				W_PWM   = r_data[9];
 				C_PWM   = r_data[10];
 
+				/* Migrate the old 0..10 color mix to the new 0..100 scale. */
+				if(Mode == mode0 && W_PWM <= 10U && C_PWM <= 10U && (W_PWM + C_PWM) > 0U)
+				{
+					uint16_t legacy_mix = W_PWM + C_PWM;
+					W_PWM = (uint16_t)(((uint32_t)W_PWM * 100U + legacy_mix / 2U) / legacy_mix);
+					C_PWM = 100U - W_PWM;
+				}
+
 				is_time       = r_data[12];
 			//	flag_1h       = r_data[13];//
 			//	adress        = r_data[14];
@@ -100,6 +143,28 @@ void read_user_data(void)
 				adress_H_array[4]=r_data[24]; 
 				adress_L_array[4]=r_data[25];
 				choose_mode_falsg=r_data[30];
+				/* Preserve old mode meanings after inserting new mode 9. */
+				if(r_data[FLASH_MODE_LAYOUT_INDEX] != FLASH_MODE_LAYOUT_MARK &&
+				   choose_mode_falsg >= 8U && choose_mode_falsg <= 13U)
+				{
+					choose_mode_falsg++;
+				}
+				if(choose_mode_falsg > CUSTOM_TEMPERATURE_MODE)
+					choose_mode_falsg = EFFECT_MODE_MIN;
+				if(r_data[FLASH_POWER_MODE_MARK_INDEX] == FLASH_POWER_MODE_MARK)
+				{
+					power_restore_policy = r_data[FLASH_POWER_MODE_INDEX];
+					if(power_restore_policy > POWER_RESTORE_CYCLE_STATIC)
+						power_restore_policy = POWER_RESTORE_CYCLE_STATIC;
+					power_cycle_next_mode = r_data[FLASH_POWER_CYCLE_INDEX];
+					if(power_cycle_next_mode > 2U)
+						power_cycle_next_mode = 0U;
+				}
+				else
+				{
+					power_restore_policy = POWER_RESTORE_CYCLE_STATIC;
+					power_cycle_next_mode = 0U;
+				}
 				//choose_mode_bh=r_data[31];
 				driveMode=r_data[32];
 				flag_1h = (r_data[36] << 24) | (r_data[35] << 16) | (r_data[34] << 8) | r_data[33];
@@ -130,6 +195,7 @@ void wright_user_data(void)
   	 app_data[11] = 0;
 		 app_data[12] = is_time;
 	   app_data[13] = 0;
+		 app_data[FLASH_BRIGHTNESS_FORMAT_INDEX] = FLASH_BRIGHTNESS_PERCENT_MARK;
 		 app_data[15] = match_success;
 	
 	
@@ -144,10 +210,10 @@ void wright_user_data(void)
 		app_data[23]=adress_L_array[3];
 		app_data[24]=adress_H_array[4];
 		app_data[25]=adress_L_array[4];
-		app_data[26]=0;
-		app_data[27]=0;
-		app_data[28]=0;	
-		app_data[29]=0;
+		app_data[FLASH_MODE_LAYOUT_INDEX]=FLASH_MODE_LAYOUT_MARK;
+		app_data[FLASH_POWER_MODE_MARK_INDEX]=FLASH_POWER_MODE_MARK;
+		app_data[FLASH_POWER_MODE_INDEX]=power_restore_policy;
+		app_data[FLASH_POWER_CYCLE_INDEX]=power_cycle_next_mode;
 		app_data[30]=choose_mode_falsg;
 		app_data[31]=choose_mode_bh;
 		app_data[32]=driveMode;
@@ -173,5 +239,59 @@ void fmc_spi_read(void)
 }	
 
 
+void power_restore_policy_set(uint8_t policy)
+{
+	if(policy > POWER_RESTORE_CYCLE_STATIC) return;
 
+	if(policy == POWER_RESTORE_CYCLE_STATIC &&
+	   power_restore_policy != POWER_RESTORE_CYCLE_STATIC)
+		power_cycle_next_mode = 0U;
 
+	if(policy == power_restore_policy) return;
+
+	power_restore_policy = policy;
+	set_TaskComps_timer(2U, POWER_POLICY_SAVE_DELAY_MS);
+}
+
+void power_restore_apply_on_boot(void)
+{
+	uint8_t mode_index;
+
+	if(power_restore_policy != POWER_RESTORE_CYCLE_STATIC) return;
+
+	mode_index = power_cycle_next_mode;
+	if(mode_index > 2U) mode_index = 0U;
+
+	deviceStatus = POWERON;
+	Mode = mode0;
+	choose_mode_falsg = mode_index;
+	choose_mode_bh = 0U;
+
+	if(mode_index == 0U)
+	{
+		W_PWM = 100U;
+		C_PWM = 0U;
+		driveMode = 1U;
+	}
+	else if(mode_index == 1U)
+	{
+		W_PWM = 0U;
+		C_PWM = 100U;
+		driveMode = 2U;
+	}
+	else
+	{
+		W_PWM = 50U;
+		C_PWM = 50U;
+		driveMode = 0U;
+	}
+
+	power_cycle_next_mode = (uint8_t)((mode_index + 1U) % 3U);
+
+	/*
+	 * Cycle-static is also a remembered state.  Start PWM, BLE and the
+	 * H-bridge through the same path as full-memory restore, then persist
+	 * the next static mode through the normal deferred Flash state machine.
+	 */
+	set_TaskComps_timer(2U, POWER_POLICY_SAVE_DELAY_MS);
+}

project/example/ble/ble_peripheral/app/src/fmc_spi.h

@@ -37,6 +37,9 @@ extern "C" {
 #include <string.h>
 #include <stdint.h>
 
+#define POWER_RESTORE_FULL_MEMORY  0U
+#define POWER_RESTORE_CYCLE_STATIC 1U
+
 /*------------------------------------------------------------------------------------
 	                                     Macros
  -------------------------------------------------------------------------------------*/
@@ -49,12 +52,15 @@ extern "C" {
 	                                 Global Variables
  -------------------------------------------------------------------------------------*/
  extern uint8_t data[];
+ extern uint8_t power_restore_policy;
 /*------------------------------------------------------------------------------------
 	                                Exported Functions
  -------------------------------------------------------------------------------------*/
 void fmc_spi_wright(void);
 void fmc_spi_dma_demo(void);
 void fmc_spi_read(void);
+void power_restore_apply_on_boot(void);
+void power_restore_policy_set(uint8_t policy);
 #ifdef __cplusplus
 }
 #endif

project/example/ble/ble_peripheral/app/src/light_transition.c

@@ -0,0 +1,540 @@
+#include "pwm.h"
+#include "mode.h"
+#include "light_transition.h"
+
+volatile uint8_t Light_Transition_FadeActive;
+volatile uint8_t Light_Transition_ModeActive;
+volatile uint32_t Light_Transition_W_Output_Q12;
+volatile uint32_t Light_Transition_C_Output_Q12;
+
+#define BRIGHTNESS_SMOOTH_SHIFT 4U
+#define OUTPUT_SMOOTH_SHIFT 4U
+#define MODE_TRANSITION_TICKS 100U
+#define CCT_RING_TRANSITION_TICKS 40U
+#define TRANSITION_CURVE_LINEAR 0U
+#define TRANSITION_CURVE_GAMMA_S 1U
+#define TRANSITION_CURVE_GAMMA_OUT 2U
+#define LIGHT_OUTPUT_SCALE 1000U
+#define BREATH_MIN_OUTPUT (LIGHT_OUTPUT_SCALE / 100U)
+#define DUAL_MIN_STABLE_CHANNEL_OUTPUT 102U
+#define POWER_FADE_Q12_MAX 4096U
+#define POWER_FADE_ON_TICKS 140U
+#define POWER_FADE_OFF_TICKS 160U
+#define POWER_FADE_ON_STEP (POWER_FADE_Q12_MAX / POWER_FADE_ON_TICKS)
+#define POWER_FADE_ON_REMAINDER (POWER_FADE_Q12_MAX % POWER_FADE_ON_TICKS)
+#define POWER_FADE_OFF_STEP (POWER_FADE_Q12_MAX / POWER_FADE_OFF_TICKS)
+#define POWER_FADE_OFF_REMAINDER (POWER_FADE_Q12_MAX % POWER_FADE_OFF_TICKS)
+
+/*
+ * Gamma 1.8, mapping APP levels 1..100 to a physical range of 1%..100%.
+ * Values are Q12 scale factors, so the runtime path is only:
+ * table lookup + multiply + shift.
+ */
+static const uint16_t brightness_gamma_q12[100] = {
+    41U, 42U, 45U, 48U, 54U, 60U, 67U, 75U, 85U, 95U,
+    106U, 119U, 132U, 146U, 161U, 177U, 193U, 211U, 229U, 249U,
+    269U, 290U, 311U, 334U, 357U, 381U, 406U, 432U, 459U, 486U,
+    514U, 542U, 572U, 602U, 633U, 665U, 697U, 731U, 764U, 799U,
+    834U, 871U, 907U, 945U, 983U, 1022U, 1061U, 1102U, 1143U, 1184U,
+    1227U, 1270U, 1313U, 1358U, 1403U, 1449U, 1495U, 1542U, 1590U, 1638U,
+    1687U, 1737U, 1787U, 1838U, 1890U, 1942U, 1995U, 2049U, 2103U, 2158U,
+    2214U, 2270U, 2327U, 2384U, 2442U, 2501U, 2560U, 2620U, 2681U, 2742U,
+    2804U, 2867U, 2930U, 2993U, 3058U, 3123U, 3188U, 3255U, 3321U, 3389U,
+    3457U, 3525U, 3595U, 3664U, 3735U, 3806U, 3878U, 3950U, 4023U, 4096U
+};
+
+/*
+ * Mixed-light Gamma table. Its first level equals the original level 41
+ * (834/4096), where a 50:50 mix measures about 46 us per direction at 2 kHz.
+ * The remaining range is expanded to 100%, so all brightness levels remain
+ * distinct instead of clamping the lower levels to one fixed output.
+ */
+static const uint16_t mixed_brightness_gamma_q12[100] = {
+    834U, 835U, 837U, 840U, 844U, 849U, 855U, 861U, 869U, 877U,
+    886U, 897U, 907U, 918U, 931U, 943U, 956U, 971U, 985U, 1001U,
+    1017U, 1034U, 1051U, 1070U, 1088U, 1108U, 1128U, 1149U, 1170U, 1192U,
+    1214U, 1237U, 1261U, 1285U, 1310U, 1336U, 1362U, 1389U, 1416U, 1444U,
+    1472U, 1502U, 1531U, 1561U, 1592U, 1623U, 1655U, 1688U, 1720U, 1753U,
+    1788U, 1823U, 1857U, 1893U, 1930U, 1967U, 2004U, 2041U, 2080U, 2119U,
+    2158U, 2198U, 2239U, 2280U, 2321U, 2363U, 2406U, 2449U, 2493U, 2537U,
+    2582U, 2627U, 2673U, 2719U, 2765U, 2813U, 2860U, 2909U, 2958U, 3007U,
+    3057U, 3107U, 3158U, 3209U, 3261U, 3313U, 3366U, 3419U, 3473U, 3527U,
+    3582U, 3637U, 3693U, 3748U, 3806U, 3863U, 3921U, 3979U, 4037U, 4096U
+};
+
+/*
+ * Gamma 1.8 envelope for power-on/off. The transition progress is advanced
+ * independently of the requested brightness, so every turn-on takes about
+ * 700 ms and every turn-off takes about 800 ms. Linear interpolation between
+ * table entries prevents visible 1% steps.
+ */
+static const uint16_t power_fade_gamma_q12[101] = {
+    0U, 1U, 4U, 7U, 12U, 19U, 26U, 34U, 43U, 54U,
+    65U, 77U, 90U, 104U, 119U, 135U, 151U, 169U, 187U, 206U,
+    226U, 247U, 268U, 291U, 314U, 338U, 363U, 388U, 414U, 441U,
+    469U, 498U, 527U, 557U, 588U, 619U, 651U, 684U, 718U, 752U,
+    787U, 823U, 859U, 897U, 934U, 973U, 1012U, 1052U, 1093U, 1134U,
+    1176U, 1219U, 1262U, 1306U, 1351U, 1396U, 1442U, 1489U, 1536U, 1585U,
+    1633U, 1682U, 1732U, 1783U, 1834U, 1886U, 1939U, 1992U, 2046U, 2100U,
+    2155U, 2211U, 2268U, 2325U, 2382U, 2440U, 2499U, 2559U, 2619U, 2680U,
+    2741U, 2803U, 2866U, 2929U, 2993U, 3057U, 3122U, 3188U, 3254U, 3321U,
+    3388U, 3456U, 3525U, 3594U, 3664U, 3735U, 3806U, 3877U, 3950U, 4023U,
+    4096U
+};
+
+/*
+ * Symmetric Gamma 1.8 transition curve:
+ * q = p^1.8 / (p^1.8 + (1-p)^1.8)
+ *
+ * Unlike applying Gamma independently to W and C, q and (1-q) remain
+ * complementary. The transition therefore eases in and out without causing
+ * a brightness dip in the middle. A table keeps the 5 ms task free of
+ * floating-point and power calculations.
+ */
+static const uint16_t transition_gamma_s_q12[101] = {
+    0U, 1U, 4U, 8U, 13U, 20U, 29U, 39U, 50U, 63U,
+    77U, 93U, 110U, 130U, 150U, 173U, 197U, 223U, 251U, 281U,
+    312U, 345U, 381U, 418U, 457U, 498U, 541U, 586U, 633U, 681U,
+    732U, 784U, 839U, 895U, 953U, 1012U, 1073U, 1136U, 1200U, 1265U,
+    1332U, 1400U, 1469U, 1539U, 1610U, 1682U, 1754U, 1827U, 1901U, 1974U,
+    2048U, 2122U, 2195U, 2269U, 2342U, 2414U, 2486U, 2557U, 2627U, 2696U,
+    2764U, 2831U, 2896U, 2960U, 3023U, 3084U, 3143U, 3201U, 3257U, 3312U,
+    3364U, 3415U, 3463U, 3510U, 3555U, 3598U, 3639U, 3678U, 3715U, 3751U,
+    3784U, 3815U, 3845U, 3873U, 3899U, 3923U, 3946U, 3966U, 3986U, 4003U,
+    4019U, 4033U, 4046U, 4057U, 4067U, 4076U, 4083U, 4088U, 4092U, 4095U,
+    4096U
+};
+
+static uint16_t current_brightness_q12;
+static uint16_t power_fade_progress_q12;
+static uint16_t power_fade_remainder;
+static uint8_t power_fade_direction;
+static uint8_t transition_sync_pending;
+static uint16_t mode_transition_start_w;
+static uint16_t mode_transition_start_c;
+static uint8_t mode_transition_tick;
+static uint8_t mode_transition_total_ticks;
+static uint8_t mode_transition_gamma_curve;
+static volatile uint8_t feedback_active;
+static volatile uint8_t feedback_on;
+
+static uint16_t brightness_scale_for_level(uint8_t level)
+{
+    if(level == 0U) return 0U;
+    if(level < BRIGHTNESS_MIN_PERCENT) level = BRIGHTNESS_MIN_PERCENT;
+    if(level > BRIGHTNESS_MAX_PERCENT) level = BRIGHTNESS_MAX_PERCENT;
+    return brightness_gamma_q12[level - 1U];
+}
+
+static uint16_t output_brightness_scale_for_level(uint8_t level)
+{
+    if(level == 0U) return 0U;
+    if(level < BRIGHTNESS_MIN_PERCENT) level = BRIGHTNESS_MIN_PERCENT;
+    if(level > BRIGHTNESS_MAX_PERCENT) level = BRIGHTNESS_MAX_PERCENT;
+
+    if(Mode == mode3 &&
+       (choose_mode_falsg == 7U || choose_mode_falsg == 8U))
+        return brightness_scale_for_level(level);
+
+    if(W_PWM != 0U && C_PWM != 0U)
+        return mixed_brightness_gamma_q12[level - 1U];
+
+    return brightness_scale_for_level(level);
+}
+
+static uint16_t approach_brightness_scale(uint16_t current, uint16_t target)
+{
+    uint16_t delta;
+    uint16_t step;
+
+    if(current == target) return current;
+    if(current < target)
+    {
+        delta = target - current;
+        step = (uint16_t)((delta + ((1U << BRIGHTNESS_SMOOTH_SHIFT) - 1U)) >>
+                          BRIGHTNESS_SMOOTH_SHIFT);
+        return current + step;
+    }
+
+    delta = current - target;
+    step = (uint16_t)((delta + ((1U << BRIGHTNESS_SMOOTH_SHIFT) - 1U)) >>
+                      BRIGHTNESS_SMOOTH_SHIFT);
+    return current - step;
+}
+
+static uint16_t approach_target(uint16_t current, uint16_t target)
+{
+    uint16_t delta;
+    uint16_t step;
+
+    if(current == target) return current;
+    if(current < target)
+    {
+        delta = target - current;
+        step = (uint16_t)((delta + ((1U << OUTPUT_SMOOTH_SHIFT) - 1U)) >>
+                          OUTPUT_SMOOTH_SHIFT);
+        return current + step;
+    }
+
+    delta = current - target;
+    step = (uint16_t)((delta + ((1U << OUTPUT_SMOOTH_SHIFT) - 1U)) >>
+                      OUTPUT_SMOOTH_SHIFT);
+    return current - step;
+}
+
+static uint16_t transition_gamma_s_scale(uint8_t tick, uint8_t total_ticks)
+{
+    uint16_t index;
+
+    if(total_ticks == 0U || tick >= total_ticks) return 4096U;
+    index = (uint16_t)(((uint16_t)tick * 100U +
+                       (total_ticks / 2U)) / total_ticks);
+    if(index > 100U) index = 100U;
+    return transition_gamma_s_q12[index];
+}
+
+static uint16_t transition_gamma_out_scale(uint8_t tick, uint8_t total_ticks)
+{
+    uint16_t index;
+
+    if(total_ticks == 0U || tick >= total_ticks) return 4096U;
+    index = (uint16_t)(((uint16_t)tick * 100U +
+                       (total_ticks / 2U)) / total_ticks);
+    if(index > 100U) index = 100U;
+    return (uint16_t)(4096U - power_fade_gamma_q12[100U - index]);
+}
+
+static uint16_t interpolate_mode_output(uint16_t start, uint16_t target,
+                                        uint8_t tick)
+{
+    uint32_t delta;
+    uint16_t progress_q12;
+    uint8_t total_ticks = mode_transition_total_ticks;
+
+    if(total_ticks == 0U || tick >= total_ticks) return target;
+    if(mode_transition_gamma_curve == TRANSITION_CURVE_GAMMA_S)
+        progress_q12 = transition_gamma_s_scale(tick, total_ticks);
+    else if(mode_transition_gamma_curve == TRANSITION_CURVE_GAMMA_OUT)
+        progress_q12 = transition_gamma_out_scale(tick, total_ticks);
+    else
+        progress_q12 = (uint16_t)(
+            ((uint32_t)tick * 4096U + (total_ticks / 2U)) / total_ticks);
+
+    if(target >= start)
+    {
+        delta = (uint32_t)(target - start) * progress_q12;
+        return (uint16_t)(start +
+            ((delta + 2048U) >> 12));
+    }
+
+    delta = (uint32_t)(start - target) * progress_q12;
+    return (uint16_t)(start -
+        ((delta + 2048U) >> 12));
+}
+
+static uint16_t effect_gamma_output(uint16_t level)
+{
+    if(level == 0U) return 0U;
+    if(level > 100U) level = 100U;
+    return (uint16_t)(
+        ((uint32_t)brightness_gamma_q12[level - 1U] *
+         LIGHT_OUTPUT_SCALE + 2048U) >> 12);
+}
+
+static uint16_t power_fade_scale(uint16_t progress_q12)
+{
+    uint32_t position;
+    uint16_t index;
+    uint16_t fraction;
+    uint16_t lower;
+    uint16_t upper;
+
+    if(progress_q12 >= POWER_FADE_Q12_MAX) return POWER_FADE_Q12_MAX;
+
+    position = (uint32_t)progress_q12 * 100U;
+    index = (uint16_t)(position >> 12);
+    fraction = (uint16_t)(position & 0x0FFFU);
+    lower = power_fade_gamma_q12[index];
+    upper = power_fade_gamma_q12[index + 1U];
+
+    return (uint16_t)(lower +
+        (((uint32_t)(upper - lower) * fraction + 2048U) >> 12));
+}
+
+static void update_power_fade(uint8_t powered_on)
+{
+    uint16_t step;
+
+    if(powered_on)
+    {
+        if(power_fade_direction != 1U)
+        {
+            power_fade_direction = 1U;
+            power_fade_remainder = 0U;
+        }
+        if(power_fade_progress_q12 >= POWER_FADE_Q12_MAX) return;
+
+        step = POWER_FADE_ON_STEP;
+        power_fade_remainder += POWER_FADE_ON_REMAINDER;
+        if(power_fade_remainder >= POWER_FADE_ON_TICKS)
+        {
+            power_fade_remainder -= POWER_FADE_ON_TICKS;
+            step++;
+        }
+        if(step >= POWER_FADE_Q12_MAX - power_fade_progress_q12)
+            power_fade_progress_q12 = POWER_FADE_Q12_MAX;
+        else
+            power_fade_progress_q12 += step;
+    }
+    else
+    {
+        if(power_fade_direction != 2U)
+        {
+            power_fade_direction = 2U;
+            power_fade_remainder = 0U;
+        }
+        if(power_fade_progress_q12 == 0U) return;
+
+        step = POWER_FADE_OFF_STEP;
+        power_fade_remainder += POWER_FADE_OFF_REMAINDER;
+        if(power_fade_remainder >= POWER_FADE_OFF_TICKS)
+        {
+            power_fade_remainder -= POWER_FADE_OFF_TICKS;
+            step++;
+        }
+        if(step >= power_fade_progress_q12)
+            power_fade_progress_q12 = 0U;
+        else
+            power_fade_progress_q12 -= step;
+    }
+}
+
+void Light_Transition_SyncBrightness(uint8_t level)
+{
+    current_brightness_q12 = output_brightness_scale_for_level(level);
+    power_fade_progress_q12 =
+        level == 0U ? 0U : POWER_FADE_Q12_MAX;
+    power_fade_remainder = 0U;
+    power_fade_direction = 0U;
+    transition_sync_pending = 1U;
+}
+
+void Light_Transition_BeginModeChange(void)
+{
+    mode_transition_start_w = W_PWM_duty;
+    mode_transition_start_c = C_PWM_duty;
+    mode_transition_tick = 0U;
+    mode_transition_total_ticks =
+        (choose_mode_falsg == CUSTOM_TEMPERATURE_MODE)
+        ? CCT_RING_TRANSITION_TICKS : MODE_TRANSITION_TICKS;
+    if(Mode == mode0 && choose_mode_falsg <= 2U)
+        mode_transition_gamma_curve = TRANSITION_CURVE_GAMMA_S;
+    else if(Mode == mode0 &&
+            choose_mode_falsg == CUSTOM_TEMPERATURE_MODE)
+        mode_transition_gamma_curve = TRANSITION_CURVE_GAMMA_OUT;
+    else
+        mode_transition_gamma_curve = TRANSITION_CURVE_GAMMA_S;
+    Light_Transition_ModeActive = 1U;
+}
+
+void Light_Transition_SetFeedback(uint8_t active, uint8_t on)
+{
+    feedback_active = active ? 1U : 0U;
+    feedback_on = (active && on) ? 1U : 0U;
+
+    if(feedback_active)
+    {
+        W_PWM_duty = feedback_on ? LIGHT_OUTPUT_SCALE : 0U;
+        C_PWM_duty = 0U;
+        Light_Transition_W_Output_Q12 =
+            feedback_on ? ((uint32_t)LIGHT_OUTPUT_SCALE << 12) : 0U;
+        Light_Transition_C_Output_Q12 = 0U;
+        Light_Transition_FadeActive = 1U;
+    }
+}
+
+uint8_t Light_Transition_FeedbackActive(void)
+{
+    return feedback_active;
+}
+
+void Light_Transition_Task(void)
+{
+    uint8_t powered_on = deviceStatus != POWEROFF;
+    uint16_t target_w;
+    uint16_t target_c;
+    uint16_t target_total;
+    uint16_t target_brightness_scale;
+    uint16_t brightness_scale;
+    uint16_t fade_scale;
+    uint16_t mix_total;
+    uint16_t weak_mix;
+    uint16_t required_total;
+    uint16_t floor_w;
+    uint16_t color_progress_q12;
+    uint32_t scaled_w_q12;
+    uint32_t scaled_c_q12;
+    uint8_t power_transitioning;
+
+    /*
+     * Pairing/clear feedback is an output-only overlay. Keep all normal
+     * brightness, color, mode and power state untouched while it is active.
+     */
+    if(feedback_active)
+    {
+        W_PWM_duty = feedback_on ? LIGHT_OUTPUT_SCALE : 0U;
+        C_PWM_duty = 0U;
+        Light_Transition_W_Output_Q12 =
+            feedback_on ? ((uint32_t)LIGHT_OUTPUT_SCALE << 12) : 0U;
+        Light_Transition_C_Output_Q12 = 0U;
+        Light_Transition_FadeActive = 1U;
+        return;
+    }
+
+    if(!powered_on)
+        Light_Transition_ModeActive = 0U;
+
+    /*
+     * Keep APP brightness tracking while off. Power fading is a separate
+     * envelope, so on/off duration does not change with the saved brightness.
+     */
+    target_brightness_scale = output_brightness_scale_for_level(Brightness);
+    current_brightness_q12 =
+        approach_brightness_scale(current_brightness_q12,
+                                  target_brightness_scale);
+    update_power_fade(powered_on);
+    fade_scale = power_fade_scale(power_fade_progress_q12);
+    brightness_scale = current_brightness_q12;
+    power_transitioning =
+        powered_on ? (power_fade_progress_q12 < POWER_FADE_Q12_MAX)
+                   : (power_fade_progress_q12 != 0U);
+
+    if(Mode == mode3 && choose_mode_falsg == 7U)
+    {
+        /*
+         * Continuous CCT uses one shared brightness envelope. Derive one
+         * side from the other so every visible step is strictly complementary
+         * and W + C remains constant throughout the sweep. Map the color
+         * position through the same symmetric Gamma curve used by static
+         * transitions so the ends of each sweep are also eased.
+         */
+        target_total = (uint16_t)(
+            ((uint32_t)LIGHT_OUTPUT_SCALE * brightness_scale + 2048U) >> 12);
+        color_progress_q12 =
+            transition_gamma_s_q12[(C_PWM <= 100U) ? C_PWM : 100U];
+        target_c = (uint16_t)(
+            ((uint32_t)target_total * color_progress_q12 + 2048U) >> 12);
+        if(target_c > target_total)
+            target_c = target_total;
+        target_w = target_total - target_c;
+    }
+    else if(Mode == mode1 ||
+            (Mode == mode3 && choose_mode_falsg == 8U))
+    {
+        /*
+         * Breathing and overlap-gradient amplitudes are perceptual light
+         * transitions, so both use the Gamma table instead of raw linear
+         * channel levels. Jump/flash modes remain outside this branch.
+         */
+        target_w = (uint16_t)(
+            ((uint32_t)effect_gamma_output(W_PWM) *
+             brightness_scale + 2048U) >> 12);
+        target_c = (uint16_t)(
+            ((uint32_t)effect_gamma_output(C_PWM) *
+             brightness_scale + 2048U) >> 12);
+    }
+    else
+    {
+        target_w =
+            (uint16_t)(((uint32_t)W_PWM * brightness_scale *
+                        (LIGHT_OUTPUT_SCALE / 100U) + 2048U) >> 12);
+        target_c =
+            (uint16_t)(((uint32_t)C_PWM * brightness_scale *
+                        (LIGHT_OUTPUT_SCALE / 100U) + 2048U) >> 12);
+    }
+
+    /*
+     * Keep the weaker mixed-light direction at the measured stable threshold.
+     * Raise the combined output only when the requested W:C ratio needs it.
+     * A ratio that cannot provide 102/1000 to its weak side even at full
+     * brightness is treated as single color.
+     */
+    if(W_PWM != 0U && C_PWM != 0U &&
+       !(Mode == mode1 &&
+         (choose_mode_falsg == 5U || choose_mode_falsg == 6U)) &&
+       !(Mode == mode3 &&
+         (choose_mode_falsg == 7U || choose_mode_falsg == 8U)))
+    {
+        mix_total = (uint16_t)(W_PWM + C_PWM);
+        weak_mix = (W_PWM < C_PWM) ? W_PWM : C_PWM;
+        required_total = (uint16_t)(
+            ((uint32_t)DUAL_MIN_STABLE_CHANNEL_OUTPUT * mix_total +
+             weak_mix - 1U) / weak_mix);
+
+        if(required_total > LIGHT_OUTPUT_SCALE)
+        {
+            if(W_PWM < C_PWM)
+                target_w = 0U;
+            else
+                target_c = 0U;
+        }
+        else if((uint16_t)(target_w + target_c) < required_total)
+        {
+            floor_w = (uint16_t)(
+                ((uint32_t)required_total * W_PWM +
+                 (mix_total / 2U)) / mix_total);
+            if(floor_w == 0U) floor_w = 1U;
+            if(floor_w >= required_total)
+                floor_w = required_total - 1U;
+            target_w = floor_w;
+            target_c = required_total - floor_w;
+        }
+    }
+
+    scaled_w_q12 = (uint32_t)target_w * fade_scale;
+    scaled_c_q12 = (uint32_t)target_c * fade_scale;
+    Light_Transition_W_Output_Q12 = scaled_w_q12;
+    Light_Transition_C_Output_Q12 = scaled_c_q12;
+    target_w = (uint16_t)((scaled_w_q12 + 2048U) >> 12);
+    target_c = (uint16_t)((scaled_c_q12 + 2048U) >> 12);
+
+    if(Mode == mode1 && powered_on && !power_transitioning)
+    {
+        if(W_PWM != 0U && target_w < BREATH_MIN_OUTPUT)
+            target_w = BREATH_MIN_OUTPUT;
+        if(C_PWM != 0U && target_c < BREATH_MIN_OUTPUT)
+            target_c = BREATH_MIN_OUTPUT;
+    }
+
+    if(Light_Transition_ModeActive && powered_on && !power_transitioning)
+    {
+        mode_transition_tick++;
+        W_PWM_duty =
+            interpolate_mode_output(mode_transition_start_w, target_w,
+                                    mode_transition_tick);
+        C_PWM_duty =
+            interpolate_mode_output(mode_transition_start_c, target_c,
+                                    mode_transition_tick);
+        if(mode_transition_tick >= mode_transition_total_ticks)
+        {
+            Light_Transition_ModeActive = 0U;
+        }
+    }
+    else if(((Mode == mode2 || Mode == mode3) && powered_on) ||
+       power_transitioning ||
+       transition_sync_pending)
+    {
+        W_PWM_duty = target_w;
+        C_PWM_duty = target_c;
+    }
+    else
+    {
+        W_PWM_duty = approach_target(W_PWM_duty, target_w);
+        C_PWM_duty = approach_target(C_PWM_duty, target_c);
+    }
+    transition_sync_pending = 0U;
+
+    Light_Transition_FadeActive =
+        !powered_on && (power_fade_progress_q12 != 0U ||
+                        W_PWM_duty != 0U || C_PWM_duty != 0U);
+}

project/example/ble/ble_peripheral/app/src/light_transition.h

@@ -0,0 +1,20 @@
+#ifndef LIGHT_TRANSITION_H
+#define LIGHT_TRANSITION_H
+
+#include <stdint.h>
+
+extern volatile uint8_t Light_Transition_FadeActive;
+extern volatile uint8_t Light_Transition_ModeActive;
+extern volatile uint32_t Light_Transition_W_Output_Q12;
+extern volatile uint32_t Light_Transition_C_Output_Q12;
+
+#define Light_Transition_RequestOn()  (Light_Transition_FadeActive = 0U)
+#define Light_Transition_RequestOff() (Light_Transition_FadeActive = 1U)
+
+void Light_Transition_Task(void);
+void Light_Transition_SyncBrightness(uint8_t level);
+void Light_Transition_BeginModeChange(void);
+void Light_Transition_SetFeedback(uint8_t active, uint8_t on);
+uint8_t Light_Transition_FeedbackActive(void);
+
+#endif

project/example/ble/ble_peripheral/app/src/ota_flash_interface.c

@@ -4,6 +4,14 @@
 // extern uint8_t ble_flash_operation_can_check(void);
 #include "ota_protocol.h"
 #include "fmc_spi.h"
+#include "PWM.h"
+
+#define USER_DATA_FLASH_ADDR       0x1E000UL
+#define USER_FLASH_WRITE_CHUNKS    16U
+#define USER_FLASH_CHUNK_GAP_MS    20U
+static uint8_t user_flash_write_chunk;
+static uint8_t user_flash_chunk_gap_ms;
+
 op_flash_t op_flash = {
     OP_IDEL,
 };
@@ -62,9 +70,43 @@ void ble_flash_handle(void)
         {
             //  LOGI("FMC_SPI_Flash_WritePage: op_flash.op_addr=%x\n",
             //  op_flash.op_addr);
-            GLOBAL_INT_DISABLE();
-            FMC_SPI_Flash_WritePage(op_flash.op_addr, op_flash.op_buff, 256);
-            GLOBAL_INT_RESTORE();
+            if(op_flash.op_addr == USER_DATA_FLASH_ADDR)
+            {
+                if(user_flash_chunk_gap_ms != 0U)
+                {
+                    user_flash_chunk_gap_ms--;
+                    return;
+                }
+
+                uint32_t chunk_offset =
+                    (uint32_t)user_flash_write_chunk * 16U;
+
+                Bridge_FlashBlank_Request();
+                if(Bridge_FlashBlank_Ready() == 0U)
+                    return;
+
+                GLOBAL_INT_DISABLE();
+                FMC_SPI_Flash_Write16Bytes(
+                    op_flash.op_addr + chunk_offset,
+                    &op_flash.op_buff[chunk_offset]);
+                GLOBAL_INT_RESTORE();
+                Bridge_FlashBlank_Resume();
+
+                user_flash_write_chunk++;
+                if(user_flash_write_chunk < USER_FLASH_WRITE_CHUNKS) {
+                    user_flash_chunk_gap_ms = USER_FLASH_CHUNK_GAP_MS;
+                    return;
+                }
+
+                user_flash_write_chunk = 0U;
+                user_flash_chunk_gap_ms = 0U;
+            }
+            else
+            {
+                GLOBAL_INT_DISABLE();
+                FMC_SPI_Flash_WritePage(op_flash.op_addr, op_flash.op_buff, 256);
+                GLOBAL_INT_RESTORE();
+            }
             op_flash.op_state = OP_IDEL;
 					
 						app_op_flash_flag = 2;
@@ -83,30 +125,40 @@ void ble_flash_handle(void)
         }
     } else if (op_flash.op_state == OP_WIAT_PAGE_ERASE) {
         {
+            if(op_flash.op_addr == USER_DATA_FLASH_ADDR) {
+                Bridge_FlashBlank_Request();
+                if(Bridge_FlashBlank_Ready() == 0U)
+                    return;
+            }
+
             GLOBAL_INT_DISABLE();
             FMC_SPI_Flash_Erase_Page(op_flash.op_addr);
             GLOBAL_INT_RESTORE();
+            if(op_flash.op_addr == USER_DATA_FLASH_ADDR) {
+                Bridge_FlashBlank_Resume();
+                user_flash_write_chunk = 0U;
+                user_flash_chunk_gap_ms = 0U;
+            }
             op_flash.op_state = OP_IDEL;
 		      	app_op_flash_flag = 1;
         }
     }
 }
 
-uint8_t app_data[128] = {0};
+uint8_t app_data[FLASH_PAGE_SIZE] = {0};
 
 //uint16_t app_op_flash_start = 10000;
 void app_op_flash(void)
 {
 
-		if(op_flash.op_state == OP_IDEL&&app_op_flash_flag ==0)
-			{
-				ble_flash_later_page_erase(0x1E000);
-		  }
-			else if(op_flash.op_state == OP_IDEL &&app_op_flash_flag ==1)
-			{
-				ble_flash_later_write_page(app_data,0x1E000);
-			
-			}
+        if(op_flash.op_state == OP_IDEL && app_op_flash_flag == 0U)
+        {
+            ble_flash_later_page_erase(USER_DATA_FLASH_ADDR);
+        }
+        else if(op_flash.op_state == OP_IDEL && app_op_flash_flag == 1U)
+        {
+            ble_flash_later_write_page(app_data, USER_DATA_FLASH_ADDR);
+        }
 }
 
 extern uint8_t aa;

project/example/ble/ble_peripheral/app/src/ota_flash_interface.h

@@ -7,7 +7,9 @@
 #endif // (USE_ROM_FLASH)
 #endif // !(USE_XIP)
 #include <stdint.h>
+void xc_fmc_spi_flash_write_16bytes(uint32_t addr, uint8_t *data);
 #define FMC_SPI_Flash_WritePage xc_fmc_spi_flash_write_page
+#define FMC_SPI_Flash_Write16Bytes xc_fmc_spi_flash_write_16bytes
 #define FMC_SPI_Flash_ReadPage xc_fmc_spi_flash_read_page
 #define FMC_SPI_Flash_Erase_Sector FMC_SPI_Flash_Erase_Sector
 #define FMC_SPI_Flash_Erase_Page xc_fmc_spi_flash_erase_page
@@ -42,5 +44,3 @@ int ble_flash_later_write_page(uint8_t *buff, uint32_t PageAddR);
 int ble_flash_later_sector_erase(uint32_t addr);
 
 #endif // __OTA_FLASH_INTERFACE_H_
-
-

project/example/ble/ble_peripheral/app/src/rf433_decoder.c

@@ -0,0 +1,179 @@
+#include "rf433_decoder.h"
+#include "rf433_decoder_port.h"
+
+/*
+ * DWM11 fixed-width 24-bit RF433 decoder.
+ *
+ * The input is sampled every 100 us. A complete pulse pair is evaluated on
+ * each rising edge, exactly like the proven DWM11 implementation.
+ */
+#define RF433_SYNC_HIGH_MIN_EXCLUSIVE  1u
+#define RF433_SYNC_HIGH_MAX_EXCLUSIVE  7u
+#define RF433_SYNC_LOW_MIN_EXCLUSIVE   115u
+#define RF433_SYNC_LOW_MAX_EXCLUSIVE   130u
+
+#define RF433_ZERO_HIGH_MIN            1u
+#define RF433_ZERO_HIGH_MAX            7u
+#define RF433_ZERO_LOW_MIN             7u
+#define RF433_ZERO_LOW_MAX             16u
+
+#define RF433_ONE_HIGH_MIN             7u
+#define RF433_ONE_HIGH_MAX             16u
+#define RF433_ONE_LOW_MIN              2u
+#define RF433_ONE_LOW_MAX              7u
+
+#define RF433_BIT_LEN                  24u
+
+typedef struct
+{
+    volatile uint16_t high_ticks;
+    volatile uint16_t low_ticks;
+    volatile uint8_t current_level;
+    volatile uint8_t sync_found;
+    volatile uint8_t bit_count;
+    volatile uint32_t data;
+    volatile uint8_t frame_ready;
+    Rf433DecoderFrame_t frame;
+} Rf433Dwm11Decoder_t;
+
+static Rf433Dwm11Decoder_t s_dec;
+
+static void rf433_increment_saturated(volatile uint16_t *value)
+{
+    if (*value < 0xffffu)
+    {
+        (*value)++;
+    }
+}
+
+static uint8_t rf433_in_range(uint16_t value, uint16_t min, uint16_t max)
+{
+    return (value >= min && value <= max) ? 1u : 0u;
+}
+
+static uint8_t rf433_is_sync(uint16_t high, uint16_t low)
+{
+    return (high > RF433_SYNC_HIGH_MIN_EXCLUSIVE &&
+            high < RF433_SYNC_HIGH_MAX_EXCLUSIVE &&
+            low > RF433_SYNC_LOW_MIN_EXCLUSIVE &&
+            low < RF433_SYNC_LOW_MAX_EXCLUSIVE) ? 1u : 0u;
+}
+
+static void rf433_publish_frame(uint32_t code)
+{
+    s_dec.frame.code = code;
+    s_dec.frame.bit_len = RF433_BIT_LEN;
+    s_dec.frame.addr_h = (uint8_t)((code >> 16) & 0xffu);
+    s_dec.frame.addr_l = (uint8_t)((code >> 8) & 0xffu);
+    s_dec.frame.key = (uint8_t)(code & 0xffu);
+    s_dec.frame.score = 100u;
+    s_dec.frame_ready = 1u;
+
+    RF433_DECODER_LOG("[RF433 DWM11 OK] code=0x%06X key=0x%02X\r\n",
+                      (unsigned int)code,
+                      s_dec.frame.key);
+}
+
+static void rf433_decode_bit(uint8_t bit)
+{
+    s_dec.data <<= 1;
+    if (bit != 0u)
+    {
+        s_dec.data |= 1u;
+    }
+
+    s_dec.bit_count++;
+    if (s_dec.bit_count >= RF433_BIT_LEN)
+    {
+        rf433_publish_frame(s_dec.data);
+        s_dec.sync_found = 0u;
+        s_dec.bit_count = 0u;
+    }
+}
+
+void rf433_decoder_init(void)
+{
+    s_dec.high_ticks = 0u;
+    s_dec.low_ticks = 0u;
+    s_dec.current_level = 0u;
+    s_dec.sync_found = 0u;
+    s_dec.bit_count = 0u;
+    s_dec.data = 0u;
+    s_dec.frame_ready = 0u;
+}
+
+void rf433_decoder_sample(uint8_t level)
+{
+    uint16_t high;
+    uint16_t low;
+
+    level = level ? 1u : 0u;
+
+    if (level == 0u)
+    {
+        rf433_increment_saturated(&s_dec.low_ticks);
+        s_dec.current_level = 0u;
+        return;
+    }
+
+    rf433_increment_saturated(&s_dec.high_ticks);
+
+    if (s_dec.current_level == 0u)
+    {
+        high = s_dec.high_ticks;
+        low = s_dec.low_ticks;
+
+        if (rf433_is_sync(high, low))
+        {
+            s_dec.sync_found = 1u;
+            s_dec.bit_count = 0u;
+            s_dec.data = 0u;
+        }
+        else if (s_dec.sync_found != 0u)
+        {
+            if (rf433_in_range(high, RF433_ZERO_HIGH_MIN, RF433_ZERO_HIGH_MAX) &&
+                rf433_in_range(low, RF433_ZERO_LOW_MIN, RF433_ZERO_LOW_MAX))
+            {
+                rf433_decode_bit(0u);
+            }
+            else if (rf433_in_range(high, RF433_ONE_HIGH_MIN, RF433_ONE_HIGH_MAX) &&
+                     rf433_in_range(low, RF433_ONE_LOW_MIN, RF433_ONE_LOW_MAX))
+            {
+                rf433_decode_bit(1u);
+            }
+            else
+            {
+                s_dec.sync_found = 0u;
+                s_dec.bit_count = 0u;
+                s_dec.data = 0u;
+            }
+        }
+
+        s_dec.low_ticks = 0u;
+        s_dec.high_ticks = 1u;
+    }
+
+    s_dec.current_level = 1u;
+}
+
+void rf433_decoder_process(void)
+{
+    /* DWM11 decodes directly in the 100 us sampling callback. */
+}
+
+bool rf433_decoder_get_frame(Rf433DecoderFrame_t *frame)
+{
+    if (frame == 0 || s_dec.frame_ready == 0u)
+    {
+        return false;
+    }
+
+    *frame = s_dec.frame;
+    s_dec.frame_ready = 0u;
+    return true;
+}
+
+uint16_t rf433_decoder_get_lost_count(void)
+{
+    return 0u;
+}

project/example/ble/ble_peripheral/app/src/rf433_decoder.h

@@ -0,0 +1,25 @@
+#ifndef __RF433_DECODER_H__
+#define __RF433_DECODER_H__
+
+#include <stdbool.h>
+#include <stdint.h>
+
+#define RF433_DECODER_SAMPLE_US 100u
+
+typedef struct
+{
+    uint32_t code;
+    uint8_t bit_len;
+    uint8_t addr_h;
+    uint8_t addr_l;
+    uint8_t key;
+    uint8_t score;
+} Rf433DecoderFrame_t;
+
+void rf433_decoder_init(void);
+void rf433_decoder_sample(uint8_t level);
+void rf433_decoder_process(void);
+bool rf433_decoder_get_frame(Rf433DecoderFrame_t *frame);
+uint16_t rf433_decoder_get_lost_count(void);
+
+#endif

project/example/ble/ble_peripheral/app/src/rf433_decoder_port.h

@@ -0,0 +1,16 @@
+#ifndef __RF433_DECODER_PORT_H__
+#define __RF433_DECODER_PORT_H__
+
+#ifndef RF433_DECODER_LOG
+#define RF433_DECODER_LOG(fmt, ...) ((void)0)
+#endif
+
+#ifndef RF433_DECODER_DEBUG_DETAIL
+#define RF433_DECODER_DEBUG_DETAIL 0
+#endif
+
+#ifndef RF433_DECODER_DEBUG_PULSE
+#define RF433_DECODER_DEBUG_PULSE 0
+#endif
+
+#endif

project/example/ble/ble_peripheral/app/src/timer.c

@@ -92,17 +92,26 @@ void timer0_2_init(void)
     timer_cfg.timer_div_clk = TIMER_DIV_CLK_16MHzOr16K;
     timer_cfg.timer_mode = TIMER_MODE_CYCLE;    
 
+    /* Timer0 is the independent 1 kHz bridge direction scheduler. */
+    xc_timer_init(TIMER0_IDX, &timer_cfg);
+    xc_timer_set_value(TIMER0_IDX, us);
+    xc_timer_start(TIMER0_IDX);
+
     xc_timer_init(TIMER1_IDX, &timer_cfg);
     xc_timer_set_value(TIMER1_IDX, us);
     xc_timer_start(TIMER1_IDX);
-    // Timer2 Config & Start
+    // Timer2 remains at 100 us for RF433 sampling.
     xc_timer_init(TIMER2_IDX, &timer_cfg);
-    xc_timer_set_value(TIMER2_IDX, 100); //10us
+    xc_timer_set_value(TIMER2_IDX, 100);
     xc_timer_start(TIMER2_IDX);
 
-	  NVIC_SetPriority((IRQn_Type)TIMER2_IRQn,0);
-    NVIC_EnableIRQ((IRQn_Type)TIMER2_IRQn);
-}
+    NVIC_SetPriority((IRQn_Type)TIMER0_IRQn, 0);
+    NVIC_EnableIRQ(TIMER0_IRQn);
+    NVIC_SetPriority((IRQn_Type)TIMER1_IRQn, 3);
+    NVIC_EnableIRQ(TIMER1_IRQn);
+    NVIC_SetPriority((IRQn_Type)TIMER2_IRQn, 1);
+    NVIC_EnableIRQ(TIMER2_IRQn);
+    }
 
 
 
@@ -117,8 +126,8 @@ void timer0_2_init(void)
  */
 __RAM_CODE void timer0_callback(void *context)
 {
-			 // timer_status.t0_flag = true;
-
+    (void)context;
+    Bridge_Service_1ms();
 }
 
 /**
@@ -138,6 +147,7 @@ __RAM_CODE void timer1_callback(void *context)
 				updateTimer(&timer2);
 
 	     
+
 }
 
 /**
@@ -145,84 +155,18 @@ __RAM_CODE void timer1_callback(void *context)
  * @details     Timer2 handler callback function
  * @param       void *context 
  * @retval      void
- * 100us模拟1kHZ PWM
+ * Timer2 remains dedicated to 100 us RF433 sampling.
  */
 
 uint8_t aa=0;
-__RAM_CODE void timer2_callback(void *context)  //10us
+__RAM_CODE void timer2_callback(void *context)
 {
-   rf433_receive();
-	if(deviceStatus==POWERON){
-   timeCnt++;
-		
-		if(W_PWM_duty==0){deadTime_W=0;}
-		else {deadTime_W=_deadTime;}
-		
-		if(C_PWM_duty==0){deadTime_C=0;}
-		else {deadTime_C=_deadTime;}
-   uint16_t totalPhase = (W_PWM_duty+deadTime_W) + (C_PWM_duty+deadTime_C) + 2*deadTime;   //看注释为什么要这样加(W_PWM_duty+deadTime_W) + (C_PWM_duty+deadTime_C)
-   
-		switch (driveMode)
-				{
-						case 0:  // 正+反交替（周期切换）
-							if (timeCnt < deadTime)
-							{
-									xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);  // 互补输出低
-									xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-							}
-							else
-							{
-									if (timeCnt <(deadTime + W_PWM_duty))  // 正转段
-									{
-										xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_SET);  // 互补输出低
-										xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-									}
-									else if (timeCnt < deadTime + W_PWM_duty + deadTime)  // 死区时间
-									{
-										 xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);  // 互补输出低
-										 xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-									}
-									else if (timeCnt < (totalPhase))  // 反转段
-									{
-										xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_SET);  // 互补输出低
-										xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);    // 主输出高
-									}
-									else
-									{
-												xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);  // 互补输出低
-												xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-									}
-							}
-						break;
-							 case 1:  // 只正转
-							 if(timeCnt<=W_PWM_duty){
-								    xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-							      xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_SET);  // 互补输出低
-								    aa=0;
-							 }else{
-							      xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);  // 互补输出低
-										xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-								     aa=1;
-							 }
-							
-							break;
-							case 2:  // 只反转
-								 if(timeCnt<=C_PWM_duty){
-												xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);  // 互补输出低
-												xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_SET);    // 主输出高
-									 }else{
-												xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);  // 互补输出低
-												xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-									 }
-									break;
-						default:
-									xc_gpio_write_pin(IO_PWM_W, GPIO_PIN_RESET);  // 互补输出低
-									xc_gpio_write_pin(IO_PWM_C, GPIO_PIN_RESET);    // 主输出高
-								break;
-					}	 
-      if (timeCnt >= PWMMAX){timeCnt = 0;}
-			
-		}
+    (void)context;
+    rf433_receive();
 }
 
-
+__RAM_CODE void timer3_callback(void *context)
+{
+    (void)context;
+    Bridge_Deadtime_Expired();
+}

project/example/ble/ble_peripheral/app/src/timeslice.c

@@ -9,9 +9,13 @@
 #include "timer.h"
 #include "mode.h"
 #include "RF433.h"  
+#include "rf433_decoder.h"
 #include "ota_flash_interface.h"
 #include "ota_protocol.h"
 #include "pwm.h"
+#include "light_transition.h"
+#include "usr_server.h"
+#include "external_key.h"
 /*********************************************************************************************************************/   
 
 void rwip_schedule(void);
@@ -21,13 +25,16 @@ TASK_COMPONENTS TaskComps[] =
 		  {0, 100, 30, ble_message_process},			  //蓝牙处理任务 
 	    {0, 0, 0, app_op_flash_on},								
 			{0,1,1,choice_mode},
-			{0,1,1,set_mode},
+			{0,5,5,set_mode},
 			{0,1,1,Set_timing},
 			{0,100,100,scan_433},	
 			{0, 100,3,  Encoder_key},
 			{0,1,1,My_ADC_Get_Value},
+			{0,50,50,ble_state_sync_poll},
 			{0, 311, 1, app_op_flash},					  //用户数据持久化 fmc_spi_read9	 			
 	 	  {0, 311, 1, xc_ota_schedule},					//保存flash数据任务				8  //最后调用的
+			{0, 1, 1, rf433_decoder_process},
+			{0, 10, 10, external_key_scan},				//GPIO5 external key scan
 };
 
 /**************************************************************************************

project/example/ble/ble_peripheral/app/src/uart.c

@@ -37,6 +37,7 @@
 #include "timer.h"
 #include "math.h"
 #include "timeslice.h"
+#include "fmc_spi.h"
 
 /*------------------------------------------------------------------------------------
                                         Macros
@@ -83,7 +84,6 @@ void uart_receive_cb(uint8_t *buff, uint16_t len)
 void scan_uar_data(uint8_t *frame){
 	
 }
-extern uint8_t sss;
 uint8_t rx_date;
 void scan_uart(uint8_t *arr)
 {
@@ -105,8 +105,7 @@ void scan_uart(uint8_t *arr)
             checksum += user_rx_buf[i];
         }
          user_rx_buf[5] = checksum; // 校验位
-				sss=1;
-			//	printf("sss=%d\r\n",sss);
+				set_TaskComps_timer(2U, 1000U);
 				switch (user_rx_buf[4])
 						{
 							  
@@ -124,38 +123,37 @@ void scan_uart(uint8_t *arr)
 							    	break;
 								case 2:
 									if(POWEROFF==deviceStatus)break;
+										if(user_rx_buf[1] < 1U || user_rx_buf[1] > (EFFECT_MODE_MAX + 1U)) break;
 										choose_mode_bh=0;
-										choose_mode_falsg=user_rx_buf[1]-1;
+										choose_mode_falsg=user_rx_buf[1]-1U;
 								    startTimer(&timer1,1);
 										break;
-								case 3: 
+								case 5:
 					
 								 break;
-								case 4:
+								case 3:
 										if(POWEROFF==deviceStatus)break;
 										if(Mode==mode0){
-											 if(user_rx_buf[1]<=20)user_rx_buf[1]=20;
-												Brightness=user_rx_buf[1]/10;
+											if(user_rx_buf[1] < BRIGHTNESS_MIN_PERCENT)
+												user_rx_buf[1] = BRIGHTNESS_MIN_PERCENT;
+											else if(user_rx_buf[1] > BRIGHTNESS_MAX_PERCENT)
+												user_rx_buf[1] = BRIGHTNESS_MAX_PERCENT;
+											Brightness = user_rx_buf[1];
 										}
 									 break;
-								case 5:	
+								case 4:
 										if(POWEROFF==deviceStatus)break;
+										  if(user_rx_buf[1] > SPEED_MAX_LEVEL)
+											  user_rx_buf[1] = SPEED_MAX_LEVEL;
 										  Speed =user_rx_buf[1];
 										break;	
 								case 6:	   
 											if(POWEROFF==deviceStatus)break;
 							
-											if(user_rx_buf[1]<=5){
-											  temperature(250);
-											}
-											else if(user_rx_buf[1]>=250){
-										      	temperature(50);
-											}else {
-												temperature(227-(57 +(((user_rx_buf[1] - 5)* 110) / 245)));
-											}
+											temperature(user_rx_buf[1]);
 											Mode=mode0;
 											choose_mode_bh=0;
-											choose_mode_falsg=10;//圆环模式	
+											choose_mode_falsg=CUSTOM_TEMPERATURE_MODE;//圆环模式
 											startTimer(&timer1,1);											
 										break;	
 								case 10:	
@@ -173,6 +171,20 @@ void scan_uart(uint8_t *arr)
 										 flag_1h=flag_1h*60000;
 								     //flag_1h=2000;
 										break;	
+								case 12:
+										power_restore_policy_set(user_rx_buf[1]);
+										break;
+								case 13:
+										if(user_rx_buf[1] == 0x01U)
+											rf433_start_pairing();
+										else
+											rf433_cancel_pairing();
+										break;
+								case 14:
+										/* A5 guard prevents accidental clear. */
+										if(user_rx_buf[1] == 0xA5U)
+											rf433_clear_code();
+										break;
 								case 9:	
 
 										break;									

project/example/ble/ble_peripheral/app/src/usr_server.c

@@ -12,6 +12,9 @@
  ****************************************************************************************
  */
 #include "usr_server.h"
+#include "Mode.h"
+#include "PWM.h"
+#include "fmc_spi.h"
 #if (BLE_APP_PRESENT)
 
 uint8_t srv_user_lid                                = GATT_INVALID_USER_LID;
@@ -83,6 +86,143 @@ uint16_t srv_get_hdl_from_att_idx(uint8_t idx)
 }
 
 uint8_t send_flag=1;
+
+#define BLE_STATE_DIRTY_POWER       0x01U
+#define BLE_STATE_DIRTY_MODE        0x02U
+#define BLE_STATE_DIRTY_BRIGHTNESS  0x04U
+#define BLE_STATE_DIRTY_SPEED       0x08U
+#define BLE_STATE_DIRTY_TEMPERATURE 0x10U
+#define BLE_STATE_DIRTY_POWER_MODE  0x20U
+#define BLE_STATE_DIRTY_ALL         0x3FU
+
+static uint8_t ble_state_dirty = BLE_STATE_DIRTY_ALL;
+static uint8_t ble_last_power;
+static uint8_t ble_last_mode;
+static uint8_t ble_last_brightness;
+static uint8_t ble_last_speed;
+static uint8_t ble_last_temperature;
+static uint8_t ble_last_power_mode;
+static volatile uint8_t ble_remote_event_pending;
+static volatile uint8_t ble_remote_event_command;
+static volatile uint8_t ble_remote_event_status;
+static volatile uint8_t ble_remote_event_paired_count;
+
+static uint8_t ble_temperature_value(void)
+{
+    uint16_t warm = W_PWM > 100U ? 100U : W_PWM;
+    return (uint8_t)((warm * 255U + 50U) / 100U);
+}
+
+void ble_state_disconnect(void)
+{
+    custom_svc_tx_char_notify = DISABLE;
+    ble_remote_event_pending = 0U;
+    send_flag = 1U;
+    ble_state_dirty = BLE_STATE_DIRTY_ALL;
+}
+
+void ble_remote_event_notify(uint8_t command, uint8_t status,
+                             uint8_t paired_count)
+{
+    if(!custom_svc_tx_char_notify) return;
+
+    ble_remote_event_command = command;
+    ble_remote_event_status = status;
+    ble_remote_event_paired_count = paired_count;
+    ble_remote_event_pending = 1U;
+}
+
+void ble_state_sync_poll(void)
+{
+    uint8_t data[4] = {0U, 0U, 0U, 0U};
+    uint8_t value;
+    uint8_t sent_mask;
+    struct app_env_tag *app_env = get_app_env();
+
+    if(!app_env->slave_connected || !custom_svc_tx_char_notify) return;
+
+    if((deviceStatus == POWERON) != ble_last_power)
+        ble_state_dirty |= BLE_STATE_DIRTY_POWER;
+    if((uint8_t)(choose_mode_falsg + 1U) != ble_last_mode)
+        ble_state_dirty |= BLE_STATE_DIRTY_MODE;
+    if(Brightness != ble_last_brightness)
+        ble_state_dirty |= BLE_STATE_DIRTY_BRIGHTNESS;
+    if(Speed != ble_last_speed)
+        ble_state_dirty |= BLE_STATE_DIRTY_SPEED;
+    if(Mode == mode0 && ble_temperature_value() != ble_last_temperature)
+        ble_state_dirty |= BLE_STATE_DIRTY_TEMPERATURE;
+    if(power_restore_policy != ble_last_power_mode)
+        ble_state_dirty |= BLE_STATE_DIRTY_POWER_MODE;
+
+    if(!send_flag) return;
+
+    /*
+     * Remote pairing/clear acknowledgements have priority over periodic
+     * state synchronization so the APP receives operation results promptly.
+     */
+    if(ble_remote_event_pending)
+    {
+        data[0] = ble_remote_event_status;
+        data[1] = ble_remote_event_paired_count;
+        data[3] = ble_remote_event_command;
+        if(slave_send_data(data, sizeof(data),
+                           CUSTOM_SVC_TX_CHAR_VAL) == GATT_NO_ERROR)
+            ble_remote_event_pending = 0U;
+        return;
+    }
+
+    if(!ble_state_dirty) return;
+
+    if(ble_state_dirty & BLE_STATE_DIRTY_POWER)
+    {
+        value = deviceStatus == POWERON;
+        data[3] = 0x01U;
+        sent_mask = BLE_STATE_DIRTY_POWER;
+    }
+    else if(ble_state_dirty & BLE_STATE_DIRTY_MODE)
+    {
+        value = choose_mode_falsg + 1U;
+        data[3] = 0x02U;
+        sent_mask = BLE_STATE_DIRTY_MODE;
+    }
+    else if(ble_state_dirty & BLE_STATE_DIRTY_BRIGHTNESS)
+    {
+        value = Brightness;
+        data[3] = 0x04U;
+        sent_mask = BLE_STATE_DIRTY_BRIGHTNESS;
+    }
+    else if(ble_state_dirty & BLE_STATE_DIRTY_SPEED)
+    {
+        value = Speed;
+        data[3] = 0x05U;
+        sent_mask = BLE_STATE_DIRTY_SPEED;
+    }
+    else if(ble_state_dirty & BLE_STATE_DIRTY_TEMPERATURE)
+    {
+        value = ble_temperature_value();
+        data[3] = 0x06U;
+        sent_mask = BLE_STATE_DIRTY_TEMPERATURE;
+    }
+    else
+    {
+        value = power_restore_policy;
+        data[3] = 0x0CU;
+        sent_mask = BLE_STATE_DIRTY_POWER_MODE;
+    }
+
+    data[0] = value;
+    if(slave_send_data(data, sizeof(data), CUSTOM_SVC_TX_CHAR_VAL) == GATT_NO_ERROR)
+    {
+        if(sent_mask == BLE_STATE_DIRTY_POWER) ble_last_power = value;
+        else if(sent_mask == BLE_STATE_DIRTY_MODE) ble_last_mode = value;
+        else if(sent_mask == BLE_STATE_DIRTY_BRIGHTNESS) ble_last_brightness = value;
+        else if(sent_mask == BLE_STATE_DIRTY_SPEED) ble_last_speed = value;
+        else if(sent_mask == BLE_STATE_DIRTY_TEMPERATURE) ble_last_temperature = value;
+        else ble_last_power_mode = value;
+        ble_state_dirty &= (uint8_t)(~sent_mask);
+    }
+}
+
 // This function is called when GATT server user has initiated event send to
 // peer device or if an error occurs.
 __STATIC void custom_svc_cb_event_sent(uint8_t conidx, uint8_t user_lid,
@@ -137,11 +277,11 @@ __STATIC __RAM_CODE void custom_svc_cb_att_val_set(uint8_t conidx, uint8_t user_
 		
     if (hdl == srv_get_hdl_from_att_idx(CUSTOM_SVC_TX_CHAR_CFG)) {
         if ((co_buf_data(p_data)[0] == 0) && (co_buf_data(p_data)[1] == 0)) {
-            //custom_svc_tx_char_notify = DISABLE;
+            custom_svc_tx_char_notify = DISABLE;
         } else {
-							//custom_svc_tx_char_notify = ENABLE;
-           /// uint8_t data[]            = {0x12, 0x13, 0x14};
-           // slave_send_data(data, sizeof(data), CUSTOM_SVC_TX_CHAR_VAL);
+            custom_svc_tx_char_notify = ENABLE;
+            send_flag = 1U;
+            ble_state_dirty = BLE_STATE_DIRTY_ALL;
         }
     }
 	/*==========================================*/
@@ -185,6 +325,7 @@ uint8_t slave_send_data(uint8_t *data, uint8_t len, uint8_t att_idx)
                                         srv_get_hdl_from_att_idx(att_idx), len,
                                         data);
         if (status != GATT_NO_ERROR) {
+            send_flag=1;
             LOGI_ERR("gatt_srv_notify error 0x%x", status);
         }
     }

project/example/ble/ble_peripheral/app/src/usr_server.h

@@ -21,7 +21,7 @@
 #include "xc_gatt_server_api.h"
 
 #define CUSTOM_SVC_UUID                   0xFFF0
-#define CUSTOM_SVC_RX_CHAR_UUID           0xFFFC
+#define CUSTOM_SVC_RX_CHAR_UUID           0xFFE4
 #define CUSTOM_SVC_TX_CHAR_UUID           0xFFF4
 #define CUSTOM_SVC_RX_CHAR_VAL_MAX_LENGTH 120
 #define CUSTOM_SVC_TX_CHAR_VAL_MAX_LENGTH 120
@@ -47,4 +47,8 @@ extern uint8_t custom_svc_tx_char_notify;
 
 uint8_t custom_svc_add(void);
 uint8_t slave_send_data(uint8_t *data, uint8_t len, uint8_t att_idx);
+void ble_state_sync_poll(void);
+void ble_state_disconnect(void);
+void ble_remote_event_notify(uint8_t command, uint8_t status,
+                             uint8_t paired_count);
 #endif // _USR_SERVER_H_

project/example/ble/ble_peripheral/mdk/Linker/cpu_xip.scat

@@ -20,6 +20,7 @@ LOAD	0x1100E000
        *(ram_em)
     }
 	ScatterAssert((0x530077b0)+ImageLength(RW2) < 0x53008000)
+	ScatterAssert(ImageLength(EXE) <= 0x10000)
 	
 
 }

project/example/ble/ble_peripheral/mdk/Linker/cpu_xip_scan.scat

@@ -22,6 +22,7 @@ LOAD	0x11011000
        *(ram_em)
     }
 	ScatterAssert((0x530077b0)+ImageLength(RW2) < 0x53008000)
+	ScatterAssert(ImageLength(EXE) <= 0xD000)
 	
 
 }

project/example/ble/ble_peripheral/mdk/Listings/startup_xinc.lst

@@ -358,10 +358,10 @@ ARM Macro Assembler    Page 6
               000000FF 
               00000000 
 Command Line: --debug --xref --diag_suppress=9931 --cpu=Cortex-M0 --apcs=interw
-ork --depend=.\objects\startup_xinc.d -o.\objects\startup_xinc.o -IC:\keil5\ARM
-\CMSIS\5.9.0\Device\ARM\ARMCM0\Include --predefine="__UVISION_VERSION SETA 538"
- --predefine="ARMCM0 SETA 1" --list=.\listings\startup_xinc.lst ..\app\src\star
-tup_xinc.s
+ork --depend=.\objects\startup_xinc.d -o.\objects\startup_xinc.o -I"D:\Program 
+Files\Keil_v5\ARM\Packs\ARM\CMSIS\5.9.0\Device\ARM\ARMCM0\Include" --predefine=
+"__UVISION_VERSION SETA 538" --predefine="ARMCM0 SETA 1" --list=.\listings\star
+tup_xinc.lst ..\app\src\startup_xinc.s
 
 
 

project/example/ble/ble_peripheral/mdk/Objects/Xinc_ble_sdk.build_log.htm

@@ -5,65 +5,341 @@
 <h2>Tool Versions:</h2>
 IDE-Version: μVision V5.38.0.0
 Copyright (C) 2022 ARM Ltd and ARM Germany GmbH. All rights reserved.
-License Information: 11 2, 2, LIC=76F5U-SYBLY-EVY1R-KVDFR-ABNKT-H3E3R
+License Information: 1 850080437@qq.com, 1, LIC=NQQMA-13CNA-CXTU6-D7Z3Q-D9AMV-Y9G1D
  
 Tool Versions:
 Toolchain:       MDK-ARM Plus  Version: 5.38.0.0
-Toolchain Path:  C:\keil5\ARM\ARMCC\Bin
-C Compiler:      Armcc.exe V5.06 update 7 (build 960)
-Assembler:       Armasm.exe V5.06 update 7 (build 960)
-Linker/Locator:  ArmLink.exe V5.06 update 7 (build 960)
-Library Manager: ArmAr.exe V5.06 update 7 (build 960)
-Hex Converter:   FromElf.exe V5.06 update 7 (build 960)
+Toolchain Path:  D:\Program Files\Keil_v5\ARM\ARMCC\Bin
+C Compiler:      Armcc.exe V5.06 update 6 (build 750)
+Assembler:       Armasm.exe V5.06 update 6 (build 750)
+Linker/Locator:  ArmLink.exe V5.06 update 6 (build 750)
+Library Manager: ArmAr.exe V5.06 update 6 (build 750)
+Hex Converter:   FromElf.exe V5.06 update 6 (build 750)
 CPU DLL:         SARMCM3.DLL V5.38.0.0
 Dialog DLL:      DARMCM1.DLL V1.19.6.0
 Target DLL:      UL2CM3.DLL V1.164.8.0
 Dialog DLL:      TARMCM1.DLL V1.14.6.0
  
 <h2>Project:</h2>
-C:\Users\31158\Desktop\蓝牙礼盒\PWM31E\hpw32e(2线3线款)\hpw32e(2线3线款)\project\example\ble\ble_peripheral\mdk\ble_peripheral.uvprojx
-Project File Date:  04/09/2026
+D:\workplace\工作文件\程序\新向远XC6517蓝牙芯片\PWM32EPRO\project\example\ble\ble_peripheral\mdk\ble_peripheral.uvprojx
+Project File Date:  07/29/2026
 
 <h2>Output:</h2>
-*** Using Compiler 'V5.06 update 7 (build 960)', folder: 'C:\keil5\ARM\ARMCC\Bin'
+*** Using Compiler 'V5.06 update 6 (build 750)', folder: 'D:\Program Files\Keil_v5\ARM\ARMCC\Bin'
 Build target 'ble-sdk-xip_scan'
-Note: source file '..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.c' - object file renamed from '.\Objects\xc_drv_spi.o' to '.\Objects\xc_drv_spi_1.o'.
-Note: source file '..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.c' - object file renamed from '.\Objects\xc_drv_fmc_spi.o' to '.\Objects\xc_drv_fmc_spi_1.o'.
-Note: source file '..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.c' - object file renamed from '.\Objects\xc_drv_fmc_spi.o' to '.\Objects\xc_drv_fmc_spi_1.o'.
-Note: source file '..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.c' - object file renamed from '.\Objects\xc_drv_spi.o' to '.\Objects\xc_drv_spi_1.o'.
 Note: source file '..\app\src\uart.c' - object file renamed from '.\Objects\uart.o' to '.\Objects\uart_1.o'.
-compiling xc_drv_spi.c...
+compiling external_key.c...
+..\app\src\Mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\Mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\Mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\Mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\Mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\PWM.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\PWM.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\PWM.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\PWM.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\external_key.c: 15 warnings, 0 errors
+compiling timer.c...
+..\app\src\PWM.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\PWM.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\PWM.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\PWM.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\timer.c: 15 warnings, 0 errors
+compiling fmc_spi.c...
 ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h(230): warning:  #47-D: incompatible redefinition of macro "CUR_PAGE_NUM"  (declared at line 115 of "..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h")
   #define CUR_PAGE_NUM(addr)             (addr / FLASH_PAGE_SIZE)
 ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h(231): warning:  #47-D: incompatible redefinition of macro "CUR_START_PSR"  (declared at line 116 of "..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h")
   #define CUR_START_PSR(addr)            (addr % FLASH_PAGE_SIZE)
 ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h(237): warning:  #47-D: incompatible redefinition of macro "FMC_IDLE_STATUS"  (declared at line 78 of "..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h")
   #define FMC_IDLE_STATUS                ((uint32_t)0x01 << 31)
-..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.c: 3 warnings, 0 errors
-compiling xc_drv_fmc_spi.c...
-..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h(230): warning:  #47-D: incompatible redefinition of macro "CUR_PAGE_NUM"  (declared at line 115 of "..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h")
-  #define CUR_PAGE_NUM(addr)             (addr / FLASH_PAGE_SIZE)
-..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h(231): warning:  #47-D: incompatible redefinition of macro "CUR_START_PSR"  (declared at line 116 of "..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h")
-  #define CUR_START_PSR(addr)            (addr % FLASH_PAGE_SIZE)
-..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h(237): warning:  #47-D: incompatible redefinition of macro "FMC_IDLE_STATUS"  (declared at line 78 of "..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h")
-  #define FMC_IDLE_STATUS                ((uint32_t)0x01 << 31)
-..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.c: 3 warnings, 0 errors
+..\app\src\mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\PWM.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\PWM.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\PWM.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\PWM.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\fmc_spi.c(179): warning:  #177-D: variable "i"  was declared but never referenced
+       uint8_t i = 0;
+..\app\src\fmc_spi.c(234): warning:  #167-D: argument of type "uint8_t (*)[256]" is incompatible with parameter of type "uint8_t *"
+  			xc_fmc_spi_flash_read_page(0x1E000,&r_data, FLASH_PAGE_SIZE);
+..\app\src\fmc_spi.c: 20 warnings, 0 errors
+compiling uart.c...
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\pwm.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\pwm.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\pwm.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\pwm.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\uart.c(153): warning:  #223-D: function "temperature" declared implicitly
+  											temperature(user_rx_buf[1]);
+..\app\src\uart.c(90): warning:  #177-D: variable "uart_handle"  was declared but never referenced
+          uint8_t uart_handle = UART0_IDX;
+..\app\src\uart.c(211): warning:  #1-D: last line of file ends without a newline
+         
+..\app\src\uart.c: 18 warnings, 0 errors
+compiling arch_main.c...
+..\app\src\pwm.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\pwm.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\pwm.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\pwm.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\arch_main.c(163): warning:  #223-D: function "xc_fmc_spi_init_oprt" declared implicitly
+      xc_fmc_spi_init_oprt();
+..\app\src\arch_main.c(164): warning:  #223-D: function "xc_fmc_spi_flash_wake_up" declared implicitly
+      xc_fmc_spi_flash_wake_up();
+..\app\src\arch_main.c(166): warning:  #223-D: function "xc_fmc_spi_flash_rdid" declared implicitly
+      xc_fmc_spi_flash_rdid((uint8_t *)&mid);
+..\app\src\arch_main.c(171): warning:  #223-D: function "xc_fmc_spi_flash_ruid" declared implicitly
+      xc_fmc_spi_flash_ruid(ruid);
+..\app\src\arch_main.c(188): warning:  #223-D: function "xc_unique_identification_read" declared implicitly
+      if (false == xc_unique_identification_read(co_default_bdaddr.addr)) {
+..\app\src\arch_main.c(161): warning:  #177-D: variable "flash_size"  was declared but never referenced
+      uint32_t flash_size;
+..\app\src\arch_main.c(162): warning:  #177-D: variable "flash_type"  was declared but never referenced
+      uint16_t flash_type;
+..\app\src\arch_main.c(215): warning:  #144-D: a value of type "uint32_t *" cannot be used to initialize an entity of type "uint8_t *"
+      uint8_t *ptr = (uint32_t *)(0x10000800);
+..\app\src\arch_main.c(375): warning:  #188-D: enumerated type mixed with another type
+      wdt_cfg.ReloadValue = WDT_CLK_32K_RESET_MODE0_8192MS;
+..\app\src\arch_main.c(395): warning:  #223-D: function "xc_fmc_spi_init_oprt" declared implicitly
+  	  xc_fmc_spi_init_oprt( );
+..\app\src\arch_main.c(396): warning:  #223-D: function "xc_fmc_spi_flash_wake_up" declared implicitly
+      xc_fmc_spi_flash_wake_up();
+..\app\src\arch_main.c(463): warning:  #223-D: function "TaskProcess" declared implicitly
+       TaskProcess();
+..\app\src\arch_main.c: 27 warnings, 0 errors
+compiling timeslice.c...
+..\app\src\mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\pwm.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\pwm.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\pwm.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\pwm.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\timeslice.c: 15 warnings, 0 errors
+compiling Rf433.c...
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\pwm.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\pwm.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\pwm.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\pwm.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\Rf433.c(659): warning:  #223-D: function "temperature" declared implicitly
+  								temperature((uint8_t)(((uint16_t)(255U - res_data) * 255U + 119U) / 239U));
+..\app\src\Rf433.c(24): warning:  #177-D: variable "POWER_flag"  was declared but never referenced
+  static uint8_t POWER_flag;
+..\app\src\Rf433.c: 17 warnings, 0 errors
+compiling Mode.c...
+..\app\src\pwm.h(137): warning:  #1295-D: Deprecated declaration _PWM_INIT - give arg types
+  void _PWM_INIT();
+..\app\src\pwm.h(143): warning:  #1295-D: Deprecated declaration adc_Init - give arg types
+  void adc_Init();
+..\app\src\pwm.h(144): warning:  #1295-D: Deprecated declaration My_ADC_Get_Value - give arg types
+  void My_ADC_Get_Value();
+..\app\src\pwm.h(145): warning:  #1295-D: Deprecated declaration gpio_pullup_input_inter_test - give arg types
+  void gpio_pullup_input_inter_test();
+..\app\src\mode.h(43): warning:  #1295-D: Deprecated declaration choice_mode - give arg types
+  void choice_mode();
+..\app\src\mode.h(44): warning:  #1295-D: Deprecated declaration set_mode - give arg types
+  void set_mode();
+..\app\src\mode.h(45): warning:  #1295-D: Deprecated declaration Start_PWM - give arg types
+  void Start_PWM();
+..\app\src\mode.h(46): warning:  #1295-D: Deprecated declaration Stop_PWM - give arg types
+  void Stop_PWM();
+..\app\src\mode.h(47): warning:  #1295-D: Deprecated declaration Set_timing - give arg types
+  void Set_timing();
+..\app\src\RF433.h(185): warning:  #1295-D: Deprecated declaration rf433_receive - give arg types
+  void rf433_receive();
+..\app\src\RF433.h(186): warning:  #1295-D: Deprecated declaration rf433_gpio_init - give arg types
+  void rf433_gpio_init();
+..\app\src\RF433.h(187): warning:  #1295-D: Deprecated declaration scan_433 - give arg types
+  void scan_433();
+..\app\src\RF433.h(188): warning:  #1295-D: Deprecated declaration Lock_Pwm7xd - give arg types
+  void Lock_Pwm7xd();
+..\app\src\RF433.h(189): warning:  #1295-D: Deprecated declaration Delay_50us - give arg types
+  void Delay_50us();
+..\app\src\RF433.h(190): warning:  #1295-D: Deprecated declaration Encoder_key - give arg types
+  void Encoder_key();
+..\app\src\Mode.c: 15 warnings, 0 errors
 linking...
-.\Objects\Xinc_ble_sdk.axf: Warning: L6304W: Duplicate input file .\objects\xc_drv_fmc_spi_1.o ignored.
-.\Objects\Xinc_ble_sdk.axf: Warning: L6304W: Duplicate input file .\objects\xc_drv_spi_1.o ignored.
-.\Linker\cpu_xip_scan.scat(16): warning: L6329W: Pattern uread4.o(.text) only matches removed unused sections.
-Program Size: Code=25664 RO-data=1368 RW-data=2676 ZI-data=3700  
-Finished: 0 information, 3 warning and 0 error messages.
+Program Size: Code=32588 RO-data=2208 RW-data=2828 ZI-data=3856  
 FromELF: creating hex file...
 After Build - User command #1: fromelf --bin --output=app.bin .\Objects\Xinc_ble_sdk.axf
 After Build - User command #2: .\output_tool\ge_ota_scan.bat
-Size of file: 27312 bytes.
-all_size=27312
+Size of file: 35064 bytes.
+all_size=35064
 dual_xip
 Addr:13000
-            Size:0x6ab0
+            Size:0x88f8
             BAddr:0x40000
-            Acheck:0x34822540
+            Acheck:0xf227e680
             SoftVer:0x10
             RomVer:0x20
             LoadAddr:0x11013000
@@ -90,9 +366,8 @@ status2=1
 需要填充0个sector
 updata file success !
 已复制         1 个文件。
-系统找不到指定的路径。
-已复制         0 个文件。
-".\Objects\Xinc_ble_sdk.axf" - 0 Error(s), 9 Warning(s).
+已复制         1 个文件。
+".\Objects\Xinc_ble_sdk.axf" - 0 Error(s), 142 Warning(s).
 
 <h2>Software Packages used:</h2>
 
@@ -102,10 +377,10 @@ Package Vendor: ARM
                 CMSIS (Common Microcontroller Software Interface Standard)
 
 <h2>Collection of Component include folders:</h2>
-  C:/keil5/ARM/CMSIS/5.9.0/Device/ARM/ARMCM0/Include
+  D:/Program Files/Keil_v5/ARM/Packs/ARM/CMSIS/5.9.0/Device/ARM/ARMCM0/Include
 
 <h2>Collection of Component Files used:</h2>
-Build Time Elapsed:  00:00:15
+Build Time Elapsed:  00:00:08
 </pre>
 </body>
 </html>

project/example/ble/ble_peripheral/mdk/Objects/Xinc_ble_sdk.lnp

@@ -14,8 +14,6 @@
 "..\app\src\rom_symdefs.o"
 ".\objects\xc_drv_dma.o"
 ".\objects\xc_drv_spi_dma.o"
-".\objects\xc_drv_spi_1.o"
-".\objects\xc_drv_fmc_spi_1.o"
 ".\objects\xc_drv_pwm.o"
 ".\objects\rf_extrc.o"
 ".\objects\ringbuffer.o"
@@ -26,13 +24,13 @@
 ".\objects\xc_drv_uart.o"
 ".\objects\xc_drv_wdt.o"
 ".\objects\xc_drv_systick.o"
-".\objects\xc_drv_fmc_spi_1.o"
+".\objects\xc_drv_fmc_spi.o"
 ".\objects\xc_drv_calib.o"
 ".\objects\xc_drv_adc.o"
 ".\objects\xc_drv_pga.o"
 ".\objects\xc_drv_aotimer.o"
 ".\objects\xc_drv_rtc.o"
-".\objects\xc_drv_spi_1.o"
+".\objects\xc_drv_spi.o"
 ".\objects\xc_gap_api.o"
 ".\objects\xc_gatt_client_api.o"
 ".\objects\xc_gatt_server_api.o"
@@ -44,7 +42,11 @@
 ".\objects\rgblight.o"
 ".\objects\mode.o"
 ".\objects\rf433.o"
+".\objects\rf433_decoder.o"
 ".\objects\pwm.o"
+".\objects\bridge_pwm.o"
+".\objects\light_transition.o"
+".\objects\external_key.o"
 ".\objects\fmc_spi.o"
 --strict --scatter ".\Linker\cpu_xip_scan.scat"
 --feedback fb.txt --summary_stderr --info summarysizes --map --load_addr_map_info --xref --callgraph --symbols

project/example/ble/ble_peripheral/mdk/Objects/aes.d

@@ -1,7 +1,7 @@
 .\objects\aes.o: ..\app\src\aes.c
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\aes\api\aes.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\aes.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\aes.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -9,9 +9,9 @@
 .\objects\aes.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
 .\objects\aes.o: ..\app\api\rwapp_config.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
-.\objects\aes.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
-.\objects\aes.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
-.\objects\aes.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\aes.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\aes.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\aes.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
@@ -19,7 +19,7 @@
 .\objects\aes.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\aes.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\aes.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -59,7 +59,7 @@
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\aes.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\aes.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\aes.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\aes.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h

project/example/ble/ble_peripheral/mdk/Objects/app_batt.d

@@ -1,6 +1,6 @@
 .\objects\app_batt.o: ..\app\src\app_batt.c
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\app_batt.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\app_batt.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -8,13 +8,13 @@
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
 .\objects\app_batt.o: ..\app\api\rwapp_config.h
 .\objects\app_batt.o: ..\app\src\app_batt.h
-.\objects\app_batt.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\app_batt.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_task.h
-.\objects\app_batt.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\app_batt.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\app_batt.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\app_batt.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -54,7 +54,7 @@
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\app_batt.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\app_batt.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -64,7 +64,7 @@
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_adc.h
 .\objects\app_batt.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwm.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_msg.h
-.\objects\app_batt.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\app_batt.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\app_batt.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\ll\gnuarm\ll.h

project/example/ble/ble_peripheral/mdk/Objects/app_sec.d

@@ -1,6 +1,6 @@
 .\objects\app_sec.o: ..\app\src\app_sec.c
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\app_sec.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\app_sec.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -8,10 +8,10 @@
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
 .\objects\app_sec.o: ..\app\api\rwapp_config.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
-.\objects\app_sec.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
-.\objects\app_sec.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\app_sec.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\app_sec.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
-.\objects\app_sec.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\app_sec.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
@@ -19,7 +19,7 @@
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\app_sec.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\app_sec.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -59,7 +59,7 @@
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\app_sec.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\app_sec.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\app_sec.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\app_sec.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h

project/example/ble/ble_peripheral/mdk/Objects/app_task.d

@@ -1,6 +1,6 @@
 .\objects\app_task.o: ..\app\src\app_task.c
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\app_task.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\app_task.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -8,8 +8,8 @@
 .\objects\app_task.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
 .\objects\app_task.o: ..\app\api\rwapp_config.h
 .\objects\app_task.o: ..\app\src\app_sec.h
-.\objects\app_task.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
-.\objects\app_task.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\app_task.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\app_task.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\app_task.o: ..\app\api\app_task.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg.h
@@ -23,7 +23,7 @@
 .\objects\app_task.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\app_task.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\app_task.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -63,7 +63,7 @@
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\app_task.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\app_task.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -73,7 +73,7 @@
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_adc.h
 .\objects\app_task.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwm.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
-.\objects\app_task.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\app_task.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\app_task.o: ..\..\..\..\..\component\ble\modules\common\api\co_hci.h

project/example/ble/ble_peripheral/mdk/Objects/arch_main.d

@@ -1,6 +1,6 @@
 .\objects\arch_main.o: ..\app\src\arch_main.c
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\arch_main.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\arch_main.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -10,9 +10,9 @@
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwr.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\arch_main.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\arch_main.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
-.\objects\arch_main.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\arch_main.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\arch_main.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\arch_main.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -52,7 +52,7 @@
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\arch_main.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\arch_main.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -73,7 +73,7 @@
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gap.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
-.\objects\arch_main.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\arch_main.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\common\api\co_hci.h
@@ -129,9 +129,11 @@
 .\objects\arch_main.o: ..\..\..\..\..\component\ble\modules\rf\api\rf.h
 .\objects\arch_main.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\arch_main.o: ..\app\src\pwm.h
-.\objects\arch_main.o: C:\keil5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\arch_main.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
 .\objects\arch_main.o: ..\app\src\mode.h
 .\objects\arch_main.o: ..\app\src\RF433.h
+.\objects\arch_main.o: ..\app\src\rf433_decoder.h
+.\objects\arch_main.o: ..\app\src\external_key.h
 .\objects\arch_main.o: ..\app\src\rgblight.h
 .\objects\arch_main.o: ..\app\src\timer.h
 .\objects\arch_main.o: ..\app\src\fmc_spi.h

project/example/ble/ble_peripheral/mdk/Objects/bridge_pwm.d

@@ -0,0 +1,61 @@
+.\objects\bridge_pwm.o: ..\app\src\bridge_pwm.c
+.\objects\bridge_pwm.o: ..\app\src\pwm.h
+.\objects\bridge_pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\bridge_pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\bridge_pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\bridge_pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\bridge_pwm.o: ..\app\src\mode.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_gpio.h
+.\objects\bridge_pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_conf.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_cpr.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_offset.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_cprao.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_rf.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_adc.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_aotimer.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_dma.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_fmc.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_fmc_cache.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_gpio.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_i2c.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_qdec.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_pwm.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_pwm_comn.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_rtc.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_spi.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_timer.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_uart.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_wdt.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_pwm_timer.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_calib.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_clock.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_systick.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwr.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_gpio.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_aotimer.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_timer.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_rtc.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\ringbuffer.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
+.\objects\bridge_pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_i2c.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_sw_i2c.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_wdt.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_adc.h
+.\objects\bridge_pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwm.h
+.\objects\bridge_pwm.o: ..\app\src\xc_drv_pwm.h
+.\objects\bridge_pwm.o: ..\app\src\light_transition.h

project/example/ble/ble_peripheral/mdk/Objects/external_key.d

@@ -0,0 +1,63 @@
+.\objects\external_key.o: ..\app\src\external_key.c
+.\objects\external_key.o: ..\app\src\external_key.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_gpio.h
+.\objects\external_key.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\external_key.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
+.\objects\external_key.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\external_key.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_conf.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_cpr.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_offset.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_cprao.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_rf.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_adc.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_aotimer.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_dma.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_fmc.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_fmc_cache.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_gpio.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_i2c.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_qdec.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_pwm.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_pwm_comn.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_rtc.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_spi.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_timer.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_uart.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_wdt.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc_m0_register\xc_reg_pwm_timer.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_calib.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_clock.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_systick.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwr.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_gpio.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_aotimer.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_timer.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_rtc.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\ringbuffer.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
+.\objects\external_key.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\external_key.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_i2c.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_sw_i2c.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_wdt.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_adc.h
+.\objects\external_key.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_pwm.h
+.\objects\external_key.o: ..\app\src\Mode.h
+.\objects\external_key.o: ..\app\src\PWM.h
+.\objects\external_key.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\external_key.o: ..\app\src\RF433.h
+.\objects\external_key.o: ..\app\src\timer.h
+.\objects\external_key.o: ..\app\src\timeslice.h

project/example/ble/ble_peripheral/mdk/Objects/fmc_spi.d

@@ -1,12 +1,12 @@
 .\objects\fmc_spi.o: ..\app\src\fmc_spi.c
 .\objects\fmc_spi.o: ..\app\src\fmc_spi.h
-.\objects\fmc_spi.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\fmc_spi.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
-.\objects\fmc_spi.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\fmc_spi.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\fmc_spi.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\fmc_spi.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\fmc_spi.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\fmc_spi.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -46,7 +46,7 @@
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\fmc_spi.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\fmc_spi.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\fmc_spi.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -58,5 +58,6 @@
 .\objects\fmc_spi.o: ..\app\src\rgblight.h
 .\objects\fmc_spi.o: ..\app\src\mode.h
 .\objects\fmc_spi.o: ..\app\src\PWM.h
-.\objects\fmc_spi.o: C:\keil5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\fmc_spi.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
 .\objects\fmc_spi.o: ..\app\src\RF433.h
+.\objects\fmc_spi.o: ..\app\src\timeslice.h

project/example/ble/ble_peripheral/mdk/Objects/light_transition.d

@@ -0,0 +1,8 @@
+.\objects\light_transition.o: ..\app\src\light_transition.c
+.\objects\light_transition.o: ..\app\src\pwm.h
+.\objects\light_transition.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\light_transition.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\light_transition.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\light_transition.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\light_transition.o: ..\app\src\mode.h
+.\objects\light_transition.o: ..\app\src\light_transition.h

project/example/ble/ble_peripheral/mdk/Objects/mode.d

@@ -1,11 +1,11 @@
 .\objects\mode.o: ..\app\src\Mode.c
 .\objects\mode.o: ..\app\src\pwm.h
-.\objects\mode.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\mode.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
-.\objects\mode.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
-.\objects\mode.o: C:\keil5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\mode.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\mode.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\mode.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\mode.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
 .\objects\mode.o: ..\app\src\xc_drv_pwm.h
-.\objects\mode.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\mode.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
@@ -47,7 +47,7 @@
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\mode.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\mode.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\mode.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -81,7 +81,7 @@
 .\objects\mode.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gap.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
-.\objects\mode.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\mode.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\modules\common\api\co_hci.h
@@ -133,3 +133,4 @@
 .\objects\mode.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_db.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gap_api.h
 .\objects\mode.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapc_msg.h
+.\objects\mode.o: ..\app\src\light_transition.h

project/example/ble/ble_peripheral/mdk/Objects/nvds.d

@@ -1,6 +1,6 @@
 .\objects\nvds.o: ..\..\..\..\..\component\ble\modules\nvds\src\nvds.c
 .\objects\nvds.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\nvds.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\nvds.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\nvds.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\nvds.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\nvds.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h

project/example/ble/ble_peripheral/mdk/Objects/ota_flash_interface.d

@@ -1,18 +1,18 @@
 .\objects\ota_flash_interface.o: ..\app\src\ota_flash_interface.c
 .\objects\ota_flash_interface.o: ..\app\src\ota_flash_interface.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
-.\objects\ota_flash_interface.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\ota_flash_interface.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\ota_flash_interface.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\ota_flash_interface.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\ota_flash_interface.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\ota_flash_interface.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\rwble_hl_error.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
 .\objects\ota_flash_interface.o: ..\app\api\rwapp_config.h
-.\objects\ota_flash_interface.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\ota_flash_interface.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
@@ -55,7 +55,7 @@
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\ota_flash_interface.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\ota_flash_interface.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_i2c.h
@@ -70,7 +70,7 @@
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\plf\refip\src\driver\reg\reg_access.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
-.\objects\ota_flash_interface.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\ota_flash_interface.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
@@ -97,3 +97,5 @@
 .\objects\ota_flash_interface.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_trc.h
 .\objects\ota_flash_interface.o: ..\app\src\ota_protocol.h
 .\objects\ota_flash_interface.o: ..\app\src\fmc_spi.h
+.\objects\ota_flash_interface.o: ..\app\src\PWM.h
+.\objects\ota_flash_interface.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h

project/example/ble/ble_peripheral/mdk/Objects/ota_protocol.d

@@ -1,6 +1,6 @@
 .\objects\ota_protocol.o: ..\app\src\ota_protocol.c
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\ota_protocol.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\ota_protocol.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -9,11 +9,11 @@
 .\objects\ota_protocol.o: ..\app\api\rwapp_config.h
 .\objects\ota_protocol.o: ..\app\src\ota_flash_interface.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
-.\objects\ota_protocol.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\ota_protocol.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\ota_protocol.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\ota_protocol.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
 .\objects\ota_protocol.o: ..\app\src\ota_protocol.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
-.\objects\ota_protocol.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\ota_protocol.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
@@ -56,7 +56,7 @@
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\ota_protocol.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\ota_protocol.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_i2c.h
@@ -71,7 +71,7 @@
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\plf\refip\src\driver\reg\reg_access.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
-.\objects\ota_protocol.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\ota_protocol.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
 .\objects\ota_protocol.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h

project/example/ble/ble_peripheral/mdk/Objects/ota_server.d

@@ -1,6 +1,6 @@
 .\objects\ota_server.o: ..\app\src\ota_server.c
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\ota_server.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\ota_server.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -9,12 +9,12 @@
 .\objects\ota_server.o: ..\app\api\rwapp_config.h
 .\objects\ota_server.o: ..\app\src\ota_protocol.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
-.\objects\ota_server.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
-.\objects\ota_server.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\ota_server.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\ota_server.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\ota_server.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\ota_server.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -54,7 +54,7 @@
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\ota_server.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\ota_server.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\ota_server.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -70,7 +70,7 @@
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\plf\refip\src\driver\reg\reg_access.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
-.\objects\ota_server.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\ota_server.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
 .\objects\ota_server.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h

project/example/ble/ble_peripheral/mdk/Objects/pwm.d

@@ -1,11 +1,11 @@
 .\objects\pwm.o: ..\app\src\PWM.c
 .\objects\pwm.o: ..\app\src\pwm.h
-.\objects\pwm.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\pwm.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
-.\objects\pwm.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
-.\objects\pwm.o: C:\keil5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
 .\objects\pwm.o: ..\app\src\xc_drv_pwm.h
-.\objects\pwm.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
@@ -47,7 +47,7 @@
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\pwm.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\pwm.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\pwm.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\pwm.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h

project/example/ble/ble_peripheral/mdk/Objects/rf433.d

@@ -1,10 +1,10 @@
 .\objects\rf433.o: ..\app\src\Rf433.c
 .\objects\rf433.o: ..\app\src\RF433.h
-.\objects\rf433.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\rf433.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
-.\objects\rf433.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\rf433.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\rf433.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\rf433.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_gpio.h
-.\objects\rf433.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\rf433.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
@@ -46,7 +46,7 @@
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\rf433.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\rf433.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\rf433.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\rf433.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -58,5 +58,80 @@
 .\objects\rf433.o: ..\app\src\uart.h
 .\objects\rf433.o: ..\app\src\mode.h
 .\objects\rf433.o: ..\app\src\timer.h
+.\objects\rf433.o: ..\app\src\light_transition.h
 .\objects\rf433.o: ..\app\src\pwm.h
-.\objects\rf433.o: C:\keil5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\rf433.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\math.h
+.\objects\rf433.o: ..\app\src\rf433_decoder.h
+.\objects\rf433.o: ..\app\src\timeslice.h
+.\objects\rf433.o: ..\app\src\usr_server.h
+.\objects\rf433.o: ..\app\api\app_task.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\rwble_hl_error.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
+.\objects\rf433.o: ..\app\api\rwapp_config.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_swdiag.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\dbg\api\dbg_trc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gap\gapm\gapm_int.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapm_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_task.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gap.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
+.\objects\rf433.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_hci.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_error.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_list.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_task.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\ll\gnuarm\ll.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\arch.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\reg_intc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_intc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\driver\reg\reg_access.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\em\api\em_map.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_math.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_et.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\em_map_ble.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_llcp.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_cs.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_tx_desc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_rx_desc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_rx_cte_desc.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_wpal.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\build\ble-full\reg\fw\_reg_em_ble_ral.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_msg_int.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gatt_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\l2cap_msg.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\common\api\co_buf.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\modules\ke\api\ke_mem.h
+.\objects\rf433.o: ..\app\src\ota_server.h
+.\objects\rf433.o: ..\app\api\app_task.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gatt_server_api.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\src\gatt\gatt_db.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\api\xc_gap_api.h
+.\objects\rf433.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gapc_msg.h

project/example/ble/ble_peripheral/mdk/Objects/rf433_decoder.d

@@ -0,0 +1,5 @@
+.\objects\rf433_decoder.o: ..\app\src\rf433_decoder.c
+.\objects\rf433_decoder.o: ..\app\src\rf433_decoder.h
+.\objects\rf433_decoder.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\rf433_decoder.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\rf433_decoder.o: ..\app\src\rf433_decoder_port.h

project/example/ble/ble_peripheral/mdk/Objects/rf_extrc.d

@@ -1,6 +1,6 @@
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\rf\src\rf_extrc.c
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
-.\objects\rf_extrc.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\rf_extrc.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\ip\ble\ll\api\rwble_config.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\rwip\api\rwip_config.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwble_hl_config.h
@@ -8,13 +8,13 @@
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\ip\ble\hl\inc\rwprf_config.h
 .\objects\rf_extrc.o: ..\app\api\rwapp_config.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\common\api\co_math.h
-.\objects\rf_extrc.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
-.\objects\rf_extrc.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
-.\objects\rf_extrc.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\rf_extrc.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\rf_extrc.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\rf_extrc.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
-.\objects\rf_extrc.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\rf_extrc.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cm0.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmInstr.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\core_cmFunc.h
@@ -71,7 +71,7 @@
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\plf\refip\src\driver\reg\reg_access.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\common\api\co_utils.h
-.\objects\rf_extrc.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\rf_extrc.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt_defines.h
 .\objects\rf_extrc.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h

project/example/ble/ble_peripheral/mdk/Objects/rgblight.d

@@ -1,10 +1,10 @@
 .\objects\rgblight.o: ..\app\src\rgblight.c
 .\objects\rgblight.o: ..\app\src\uart.h
-.\objects\rgblight.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdio.h
-.\objects\rgblight.o: C:\keil5\ARM\ARMCC\Bin\..\include\string.h
-.\objects\rgblight.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdint.h
+.\objects\rgblight.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdio.h
+.\objects\rgblight.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\string.h
+.\objects\rgblight.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdint.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\RINGBUFFER.h
-.\objects\rgblight.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdbool.h
+.\objects\rgblight.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdbool.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc6xxx.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\CMSIS\Device\xc60xx.h
@@ -46,7 +46,7 @@
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_dma.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_spi_dma.h
-.\objects\rgblight.o: C:\keil5\ARM\ARMCC\Bin\..\include\stdlib.h
+.\objects\rgblight.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stdlib.h
 .\objects\rgblight.o: ..\..\..\..\..\component\ble\modules\flash\xc6xxx_fmc_spi.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_fmc_spi_dma.h
 .\objects\rgblight.o: ..\..\..\..\..\component\xc6xx_drivers\Drivers\xc_driver\xc_drv_uart_dma.h
@@ -76,7 +76,7 @@
 .\objects\rgblight.o: ..\..\..\..\..\component\ble\ip\ble\hl\api\gap.h
 .\objects\rgblight.o: ..\..\..\..\..\component\ble\plf\refip\src\arch\compiler\gnuarm\compiler.h
 .\objects\rgblight.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
-.\objects\rgblight.o: C:\keil5\ARM\ARMCC\Bin\..\include\stddef.h
+.\objects\rgblight.o: D:\Program Files\Keil_v5\ARM\ARMCC\Bin\..\include\stddef.h
 .\objects\rgblight.o: ..\..\..\..\..\component\ble\modules\common\api\co_lmp.h
 .\objects\rgblight.o: ..\..\..\..\..\component\ble\modules\common\api\co_bt.h
 .\objects\rgblight.o: ..\..\..\..\..\component\ble\modules\common\api\co_hci.h